Plate Shape Effect on the Performance of the Vertical Axis Auto Rotation Current Turbine (VAACT)

2014 ◽  
Author(s):  
Ali Bakhshandeh Rostami ◽  
Antonio Carlos Fernandes
Keyword(s):  
Flat Plate ◽  
High Efficiency ◽  
Vertical Axis ◽  
Speed Ratio ◽  
Shape Effect ◽  
Tip Speed Ratio ◽  
Upper Limit ◽  
Plate Shape ◽  
Uniform Current ◽  
Current Turbine

The present paper explores experimentally the performance of two types of hinged plates which rotate about vertical axis when submitted to uniform current. A flat plate configuration and also a flapped plate (say, S shape) configuration have been investigated. The Vertical axis Auto rotation Current Turbine (VAACT) is one degree of freedom system (free to rotate in yaw direction). It is shown that a high efficiency for S shape type can be obtained of the order of 30 percent while flat blade type reaches approximately to 7 percent. Upper limit of tip speed ratio for flat blade type has been expanded approximately 0.9 whereas S shape approaches 1.3.

Vertical Axis Current Turbine (VACT) and its Efficiency

2013 ◽  
Author(s):  
Antonio Carlos Fernandes ◽  
Ali Bakhshandeh Rostami ◽  
Lucas Gomes Canzian ◽  
Sina Mirzaei Sefat
Keyword(s):  
Angular Velocity ◽  
Flat Plate ◽  
Water Channel ◽  
Vertical Axis ◽  
Power Coefficient ◽  
Speed Ratio ◽  
Tip Speed Ratio ◽  
Circulating Water ◽  
Property Changes ◽  
Current Turbine

This study examines the efficiency of a vertical axis current turbine (VACT) according to various non-dimensional mass moments of inertia. The vertical axis current turbine of drag force type with flat plate-shaped blade is tested. From experiments in a circulating water channel the angular velocity, the power coefficient and tip speed ratio of the vertical axis current turbine are obtained. The property changes for various conditions give the relationships between efficiency-related parameters. The maximum power coefficients of experiments occur at the tip speed ratio of approximately 0.35∼0.40. From the experiments, turbine is found to give a 7% power coefficient which related to I* = 0.52.

scholarly journals Forced Motion CFD Simulation and Load Refinement Evaluation of Floating Vertical-Axis Tidal Current Turbines

2020 ◽  
Vol 27 (3) ◽  
pp. 40-49
Author(s):  
Wanchao Zhang ◽  
Yujie Zhou ◽  
Kai Wang ◽  
Xiaoguo Zhou
Keyword(s):  
Least Squares Method ◽  
Vertical Axis ◽  
Lateral Force ◽  
Hydrodynamic Performance ◽  
Speed Ratio ◽  
Time Varying ◽  
Pitching Motion ◽  
Tip Speed Ratio ◽  
Damping Coefficients ◽  
Current Turbine

AbstractSimulation of the hydrodynamic performance of a floating current turbine in a combined wave and flow environment is important. In this paper, ANSYS-CFX software is used to analyse the hydrodynamic performance of a vertical-axis turbine with various influence factors such as tip speed ratio, pitching frequency and amplitude. Time-varying curves for thrust and lateral forces are fitted with the least squares method; the added mass and damping coefficients are refined to analyse the influence of the former factors. The simulation results demonstrate that, compared with non-pitching and rotating turbines under constant inflow, the time-varying load of rotating turbines with pitching exhibits an additional fluctuation. The pitching motion of the turbine has a positive effect on the power output. The fluctuation amplitudes of thrust and lateral force envelope curves have a positive correlation with the frequency and amplitude of the pitching motion and tip speed ratio, which is harmful to the turbine’s structural strength. The mean values of the forces are slightly affected by pitching frequencies and amplitudes, but positively proportional to the tip speed ratio of the turbine. Based upon the least squares method, the thrust and lateral force coefficients can be divided into three components, uniform load coefficient, added mass and damping coefficients, the middle one being significantly smaller than the other two. Damping force plays a more important role in the fluctuation of loads induced by pitching motion. These results can facilitate study of the motion response of floating vertical-axis tidal current turbine systems in waves.

Numerical Research on the Characteristics of Lift-Drag Type Vertical Axis Wind Turbine

2012 ◽  
Vol 189 ◽  
pp. 448-452
Author(s):  
Yan Jun Chen ◽  
Guo Qing Wu ◽  
Yang Cao ◽  
Dian Gui Huang ◽  
Qin Wang ◽  
...  
Keyword(s):  
Wind Turbine ◽  
Vertical Axis ◽  
Chord Length ◽  
Power Coefficient ◽  
Speed Ratio ◽  
Vertical Axis Wind Turbine ◽  
Tip Speed Ratio ◽  
Middle Range ◽  
Parabolic Form ◽  
Cfd Method

Numerical studies are conducted to research the performance of a kind of lift-drag type vertical axis wind turbine (VAWT) affected by solidity with the CFD method. Moving mesh technique is used to construct the model. The Spalart-Allmaras one equation turbulent model and the implicit coupled algorithm based on pressure are selected to solve the transient equations. In this research, how the tip speed ratio and the solidity of blade affect the power coefficient (Cp) of the small H-VAWT is analyzed. The results indicate that Cp curves exhibit approximate parabolic form with its maximum in the middle range of tip speed ratio. The two-blade wind turbine has the lowest Cp while the three-blade one is more powerful and the four-blade one brings the highest power. With the certain number of blades, there is a best chord length, and too long or too short chord length may reduce the Cp.

scholarly journals Implementation of Control System for Hydrokinetic Energy Converter

2013 ◽  
Vol 2013 ◽  
pp. 1-10 ◽  
Author(s):  
Katarina Yuen ◽  
Senad Apelfröjd ◽  
Mats Leijon
Keyword(s):  
Control System ◽  
Laboratory Tests ◽  
Vertical Axis ◽  
Load Control ◽  
Speed Ratio ◽  
Energy Converter ◽  
Hydrokinetic Energy ◽  
Tip Speed Ratio ◽  
The Town ◽  
Design Construction

At Uppsala University, a research group is investigating a system for converting the power in freely flowing water using a vertical-axis turbine directly connected to a permanent magnet generator. An experimental setup comprising a turbine, a generator, and a control system has been constructed and will be deployed in the Dalälven river in the town of Söderfors in Sweden. The design, construction, simulations, and laboratory tests of the control system are presented in this paper. The control system includes a startup sequence for the turbine and load control. These functions have performed satisfactorily in laboratory tests. Simulations of the system show that the power output is not maximized at the same tip-speed ratio as that which maximizes the turbine power capture.

scholarly journals Kontrol Angle of Attack untuk Optimasi Daya padaVertical Axis Wind Turbine Tipe Darrieus

2020 ◽  
Vol 8 (3) ◽  
pp. 492
Author(s):  
WAHYU AULIA NURWICAKSANA ◽  
BUDHY SETIAWAN ◽  
IKA NOER SYAMSIANA ◽  
SEPTYANA RISKITASARI
Keyword(s):  
Wind Turbine ◽  
Angle Of Attack ◽  
Vertical Axis ◽  
Speed Ratio ◽  
Trial And Error ◽  
Proportional Integral Derivative ◽  
Vertical Axis Wind Turbine ◽  
Average Efficiency ◽  
Proportional Integral ◽  
Tip Speed Ratio

ABSTRAKVAWT (Vertical Axis Wind Turbine) tipe Darrieus NACA0015 merupakan salah satu model dari turbin angin yang bekerja dengan menggunakan angin sebagai sumber penggerak. Namun dari hasil pengamatan, kecepatan angin yang ada tidak konstan setiap saat. Sehingga dari permasalahan ini perlu suatu kontrol yaitu dengan mengendalikan sudut kerja blade VAWT yang dikenal dengan kontrol angle of attack (AoA). Prinsip kerja kontrol AoA yaitu sudut blade diatur agar VAWT bekerja secara optimum dan dapat meningkatkan efisiensi. Metode kontrol AoA menggunakan PID (Proportional–Integral–Derivative) dengan memberikan nilai trial and error pada Kp, Ki, Kd. VAWT ini menggunakan konstanta TSR (Tip Speed Ratio) yaitu 4. Hasil dari penelitian ini yaitu daya yang dihasilkan VAWT dengan kontrol AoA mendapatkan rata-rata efisiensi sebesar 5.16%, sedangkan VAWT tanpa kontrol mendapatkan efisiensi sebesar 3.49%. Sehingga dapat disimpulkan bahwa dengan kontrol AoA, rata-rata efisiensi dayanya naik sebesar 1.67% dari yang tanpa kontrol.Kata Kunci: Kontrol Angle of Attack (AoA), VAWT, TSR, Efisiensi ABSTRACTVAWT (Vertical Axis Wind Turbine) type Darrieus NACA0015 is one model of a wind turbine that works by using wind as a source of propulsion. Conditions from observations, wind speeds that are not constant every time. So from this problem needs control VAWT by controlling the working angle of the VAWT blade is the angle of attack control (AoA). The principle AoA control is that the blade angle adjusted so that the VAWT works optimally and can improve the efficiency. AoA control method uses PID (Proportional-Integral-Derivative) by providing trial and error values for Kp, Ki, Kd. VAWT uses TSR (Tip Speed Ratio) constant which is 4. The results of this research, VAWT with AoA control get an average efficiency of 5.16%, while without control gets an average efficiency of 3.49%. So it can be concluded that with AoA control, the average power efficiency increases by 1.67% from those without control.Keywords: Angle of Attack (AoA) Control, VAWT, TSR, Efficiency

Optimization of a Vertical Axis Micro Wind Turbine for Low Tip Speed Ratio Operation

2012 ◽  
Author(s):  
Akshay Pendharkar ◽  
Ryan McGowan ◽  
Kevin Morillas ◽  
Mark Pinder ◽  
Narayanan Komerath
Keyword(s):  
Wind Turbine ◽  
Vertical Axis ◽  
Speed Ratio ◽  
Tip Speed Ratio

Savonius Wind Turbine Performances on Wind Concentrator

2017 ◽  
Vol 8 (1) ◽  
pp. 376
Author(s):  
Dygku. Asmanissa Awg. Osman ◽  
Norzanah Rosmin ◽  
Nor Shahida Hasan ◽  
Baharruddin Ishak ◽  
Aede Hatib Mustaamal@Jamal ◽  
...  
Keyword(s):  
Wind Turbine ◽  
Electrical Power ◽  
Vertical Axis ◽  
Angular Speed ◽  
Speed Ratio ◽  
Vertical Axis Wind Turbine ◽  
Air Compressor ◽  
Tip Speed Ratio ◽  
Savonius Wind Turbine ◽  
Air Streams

The air streams from the outlet of an air compressor can be used to generate electricity. For instance, if a micro-sized Vertical-Axis Wind-Turbine (VAWT) is installed towards the airflow, some amount of electricity can be generated before being stored in a battery bank. The research’s objectives are to design, fabricate and analyze the performance of Helical Savonius VAWT blade rotors, which is tested with and without using a wind concentrator. The Helical Savonius VAWT is tested at 0 cm without the concentrator, whereas the blade rotor is tested at concave-blade position when using the concentrator. The blade and the wind concentrator designs were based on the dimensions and the constant airflow of the air compressor. The findings suggested that the blade produced its best performance when tested using wind concentrator at concave-blade position in terms of angular speed (<em>ω</em>), tip speed ratio (<em>TSR</em>) and the generated electrical power (<em>P</em><em><sub>E</sub></em>). The findings concluded that the addition of wind concentrator increases the airflow which then provided better performances on the blades.

Numerical evaluation of optimum tip speed ratio for darrieus type vertical axis wind turbine

2020 ◽  
Vol 33 ◽  
pp. 4719-4722
Author(s):  
E. Leelakrishnan ◽  
M. Sunil Kumar ◽  
S. David Selvaraj ◽  
N. Sundara Vignesh ◽  
T.S. Abhesheka Raja
Keyword(s):  
Wind Turbine ◽  
Numerical Evaluation ◽  
Vertical Axis ◽  
Speed Ratio ◽  
Vertical Axis Wind Turbine ◽  
Tip Speed Ratio

An Experimental Study of the Aerodynamics and Performance of a Vertical Axis Wind Turbine in a Confined and Unconfined Environment

2015 ◽  
Vol 137 (5) ◽  
Author(s):  
Vincenzo Dossena ◽  
Giacomo Persico ◽  
Berardo Paradiso ◽  
Lorenzo Battisti ◽  
Sergio Dell'Anna ◽  
...  
Keyword(s):  
Experimental Study ◽  
Wind Tunnel ◽  
Wind Turbine ◽  
Vertical Axis ◽  
Tip Vortex ◽  
Speed Ratio ◽  
Vertical Axis Wind Turbine ◽  
Tip Speed Ratio ◽  
And Performance ◽  
Power Curves

This paper presents the results of a wide experimental study on an H-type vertical axis wind turbine (VAWT) carried out at the Politecnico di Milano. The experiments were carried out in a large-scale wind tunnel, where wind turbines for microgeneration can be tested in real-scale conditions. Integral torque and thrust measurements were performed, as well as detailed aerodynamic measurements to characterize the flow field generated by the turbine downstream of the rotor. The machine was tested in both a confined (closed chamber) and unconfined (open chamber) environment, to highlight the effect of wind tunnel blockage on the aerodynamics and performance of the VAWT under investigation. The experimental results, compared with the blockage correlations presently available, suggest that specific correction models should be developed for VAWTs. The experimental thrust and power curves of the turbine, derived from integral measurements, exhibit the expected trends with a peak power coefficient of about 0.28 at tip-speed ratio equal to 2.5. Flow measurements, performed in three conditions for tip speed ratio equal to 1.5, 2.5, and 3.5, show the fully three-dimensional character of the wake, especially in the tip region where a nonsymmetrical wake and tip vortex are found. The unsteady evolution of the velocity and turbulence fields further highlights the effect of aerodynamic loading on the wake unsteadiness, showing the time-dependent nature of the tip vortex and the onset of dynamic stall for tip speed ratio lower than 2.

Sign in / Sign up

Export Citation Format

Share Document