Issue of Application for the Pre-Cracked Charpy Specimens to Estimate WWER-1000 RPV Metal Embrittlement

2016 ◽  
Author(s):  
Volodymyr M. Revka ◽  
Liudmyla I. Chyrko
Keyword(s):  
Fracture Toughness ◽  
Test Data ◽  
Charpy Impact ◽  
Pressure Vessels ◽  
Reference Temperature ◽  
Fracture Toughness Test ◽  
Toughness Test ◽  
Standard Specimens ◽  
High Level ◽  
Reactor Pressure

In this study the analysis of fracture toughness test data has been performed in terms of estimation of the proper T0 value for several WWER-1000 RPV materials in unirradiated condition. The surveillance test data for the standard and reconstituted specimens were included in the analysis. It was found that a reference temperature T0 for reconstituted specimens is 31°C higher on average in comparison to the standard specimens. The possible reason is a high level of the stress intensity factor Kmax during the cycle at the stage of completion of crack tip sharpening for standard specimens. Furthermore, the Charpy impact and fracture toughness test data for standard and reconstituted specimens have been compared considering the known relationship between the reference temperature T0 and the transition temperature T28J which corresponds to the Charpy energy level of 28 J. Another objective of this study was to compare the RPV metal embrittlement rate for the two reactor pressure vessels using surveillance test data from standard and reconstituted fracture toughness specimens. The analysis has shown that test data for the reconstituted specimens is consistent with the test data for the standard specimens with regard to the embrittlement rate.

Application of Master Curve Approach to Surveillance Test Data for WWER-1000 Reactor Pressure Vessels

2017 ◽  
Author(s):  
Volodymyr M. Revka ◽  
Liudmyla I. Chyrko
Keyword(s):  
Fracture Toughness ◽  
Weld Metal ◽  
Test Data ◽  
Master Curve ◽  
Pressure Vessels ◽  
Reference Temperature ◽  
Transition Curve ◽  
Surveillance Program ◽  
Data Set ◽  
Reactor Pressure

An important issue in the safety operation of WWER-1000 type reactor is a decrease in fracture toughness for reactor pressure vessel steels due to neutron irradiation. This effect for RPV metal is known as radiation embrittlement. The radiation induced temperature shift of the fracture toughness transition curve is considered as a measure of the embrittlement rate. The Charpy impact and fracture toughness specimens are included in the surveillance program for an assessment of changes in fracture toughness of RPV materials. The present analysis is based on a large data set which includes mostly experimental results for pre-cracked Charpy specimens from a WWER-1000 RPV surveillance program. A Master curve approach is applied to analyze the surveillance test data with respect to a shape of the fracture toughness transition curve and a scatter of KJC values. The RPV base and weld metal in unirradiated, thermally aged and irradiated conditions are considered in this study. The maximum shift in a reference temperature T0 due to irradiation is 107 degree Celsius. It is shown that the Master curve, 5 % and 95 % tolerance bounds describe adequately the temperature dependence and the statistical scatter of KJC values for WWER-1000 RPV steels both in unirradiated condition and after irradiation up to design as well as long term operation neutron fluence. Furthermore, a development of the Weibull plots for considered data sets is shown that the Weibull slope is close to the expected one of 4 on average. Finally, a comparison of the reference temperature T0 and a scatter of KJC values derived from the pre-cracked Charpy and 0,5T C(T) specimens of base and weld metal in unirradiated condition is done. The analysis has shown a significant discrepancy between the T0 values derived from the two different types of specimens for both RPV metals.

Evaluation of Fracture Toughness Test Data for Multilayer Dissimilar Joint Welds Using a Weibull Stress Model

2012 ◽  
pp. 357-376
Author(s):  
Yasuhito Takashima ◽  
Mitsuru Ohata ◽  
Masaru Seto ◽  
Yoshitomi Okazaki ◽  
Fumiyoshi Minami
Keyword(s):  
Fracture Toughness ◽  
Test Data ◽  
Dissimilar Joint ◽  
Fracture Toughness Test ◽  
Stress Model ◽  
Toughness Test ◽  
Weibull Stress

Fracture Toughness of Highly Irradiated Pressure Vessel Steels in the Upper Shelf Temperature

2006 ◽  
Author(s):  
Hiroshi Matsuzawa ◽  
Toru Osaki
Keyword(s):  
Fracture Toughness ◽  
Chemical Composition ◽  
Reference Material ◽  
Fast Neutron ◽  
Pressure Vessel ◽  
Charpy Impact ◽  
Pressure Vessels ◽  
Shelf Energy ◽  
Pressure Vessel Steels ◽  
Reactor Pressure

Nine Reactor Pressure Vessel (RPV) Steels and four RPV weld were irradiated up to 1.2 × 1024n/m2 fast neutron fluence (E>1MeV), and their fracture toughness and Charpy impact energy were measured. As chemical compositions, such as Cu, are known to affect the fracture toughness reduction due to neutron exposure, the above steels were fabricated by changing chemical composition widely to cover the chemical composition of the RPV materials of the operating Japanese nuclear power plants. 2.7 mm thick compact specimens were used to measure the upper shelf fracture toughness of highly irradiated materials, and their Charpy upper shelf energy was also measured. By correlating Charpy upper shelf energy to fracture toughness, the upper shelf fracture toughness evaluation formulae for highly irradiated reactor pressure vessel steels were developed. Both compact and V-notched Charpy impact specimens were irradiated in a test reactor. The fast neutron flux above 1MeV was about 5 × 1016n/(m2s). Charpy impact specimens made of Japanese PWR reference material containing 0.09w% Cu were irradiated simultaneously. The upper shelf energy of the reference material up to the medium fluence level showed little difference in the reduction of upper shelf energy to that which had been in the operating plant and which was irradiated to the same fluence. The developed correlation formulae have been adopted in the Japan Electric Association Code as new formulae to predict the fracture toughness in the upper shelf region of reactor pressure vessels. They will be applied to time limited ageing analysis of low upper shelf reactor pressure vessels in Japan, on a concrete technical basis in very high fluence regions.

Crack Arrest Test Results of Unirradiated and Irradiated German RPV Steels

2013 ◽  
Author(s):  
Florian Obermeier ◽  
Julia Barthelmes ◽  
Elisabeth Keim ◽  
Hieronymus Hein ◽  
Hilmar Schnabel ◽  
...  
Keyword(s):  
Fracture Toughness ◽  
Lower Bound ◽  
Pressure Vessel ◽  
Charpy Impact ◽  
Crack Arrest ◽  
Reactor Pressure Vessel ◽  
Test Method ◽  
Fracture Toughness Test ◽  
Test Results ◽  
Reactor Pressure

In the CARISMA[1] and CARINA[2] projects comprehensive tensile, Charpy-impact and fracture toughness tests were performed for unirradiated and irradiated original reactor pressure vessel (RPV) steel specimens from German pressurized water reactors (PWR) up to neutron fluences in the range of 60 operational years and beyond. In addition, crack arrest fracture toughness tests were performed to demonstrate the crack arrest behavior of the materials. To determine the crack arrest properties of ferritic steels, the designated test method according to ASTM E1221 [3] was used. However, in particular for irradiated reactor pressure vessel materials with higher irradiation embrittlement, the prescribed standard test specimen does not always provide adequate test results. During starter notch preparation annealing effects occurred in the heat affected zone (HAZ) of the brittle weld of the starter notch causing crack arrest in the HAZ after unstable crack initiation. Therefore a modified test method to perform crack arrest tests with so called duplex specimens was investigated. In this paper this modified method and the test results of five base and four weld metals with a fluence up to 4,69E+19 cm−2 (E >1 MeV) are discussed. The available test results show that the duplex specimen is an appropriate alternative to the standard compact crack arrest (CCA) specimen. The measured KIa fracture toughness data are enveloped by the “lower bound” of the ASME KIa-curve indexed with RTNDTj or TKIa but not all data are enveloped by indexing the “lower bound” curve with RTT0 like described in the ASME Code Case N-629 [4]. Furthermore correlations of the crack arrest test results with Charpy-impact and fracture toughness test results will be shown.

Correlations Between Charpy V-Notch Impact Energy and Fracture Toughness of Nuclear Reactor Pressure Vessel (RPV) Steels

2015 ◽  
Author(s):  
Meifang Yu ◽  
Zhen Luo ◽  
Y. J. Chao
Keyword(s):  
Fracture Toughness ◽  
Transition Region ◽  
Test Data ◽  
Impact Energy ◽  
Master Curve ◽  
Reference Temperature ◽  
Master Curve Method ◽  
Curve Method ◽  
Reactor Pressure ◽  
Actual Test

Both Charpy V-notch (CVN) impact energy and fracture toughness are parameters reflecting toughness of the material. Charpy tests are however easy to perform compared to standard fracture toughness tests, especially when the material is irradiated and quantity is limited. Correlations between the two parameters are therefore of great significance, especially for reactor pressure vessel (RPV) structural integrity assessment. In this paper, correlations between CVN impact energy and fracture toughness of three commonly used RPV steels, namely Chinese A508-3 steel, USA A533B steel, Euro 20MnMoNi55 steel, are investigated with two methods. One method applies a direct conversion using empirical formulas and the other adopts the Master Curve method. It is found that when the empirical formula is used, the difference between the predicted fracture toughness (from the CVN impact energy) and actual test data is relatively small in upper shelf, lower shelf and the bottom of transition region, while relatively large in other parts of the transition region. When the Master Curve method is adopted, whether the reference temperature T0 is estimated through temperature at 28J or 41J CVN impact energy, the predicted fracture toughness values of the three steels are consistent with actual test data. The reference temperature T0 is also estimated through the IGC-parameter correlation and through a combination of empirical formula and multi-temperature method. Both procedures show excellent agreement with test results. The mean value of T0 estimated from T28J, T41J, IGC-parameters and the combination method is denoted by TQ-ave and is then used as the final reference temperature T0 for the Master Curve determination. Accuracy of TQ-ave (and therefore the Master Curve method) is demonstrated by comparison with actual test data of the three RPV steels. It is concluded that Master Curve method provides a reliable procedure for predicting fracture toughness in the transition region utilizing limited CVN impact energy data from open literature.

Weld Material Investigations of a WWER-440 Reactor Pressure Vessel: Results From the First Trepan Taken From the Former Greifswald NPP

2009 ◽  
Vol 131 (2) ◽  
Author(s):  
Udo Rindelhardt ◽  
Hans-Werner Viehrig ◽  
Joerg Konheiser ◽  
Jan Schuhknecht
Keyword(s):  
Fracture Toughness ◽  
Pressure Vessel ◽  
Pressure Vessels ◽  
Reactor Pressure Vessel ◽  
Reference Temperature ◽  
Monte Carlo Code ◽  
Data Set ◽  
Integrity Assessment ◽  
Inner Surface ◽  
Reactor Pressure

Between 1973 and 1990 four units of the Russian nuclear power plants type WWER-440/230 were operated in Greifswald (former East Germany). Material probes from the pressure vessels were gained in the frame of the ongoing decommissioning procedure. The investigations of this material started with material from the circumferential core weld of unit 1. First, this paper presents results of the reactor pressure vessel (RPV) fluence calculations depending on different loading schemes and on the axial weld position based on the Monte Carlo code TRAMO. The results show that the use of the dummy assemblies reduces the flux by a factor of 2–5 depending on the azimuthal position. The circumferential core weld (SN0.1.4) received a fluence of 2.4×1019 neutrons/cm2 at the inner surface; it decreases to 0.8×1019 neutrons/cm2 at the outer surface. The material investigations were done using a trepan from the circumferential core weld. The reference temperature T0 was calculated with the measured fracture toughness values, KJc, at brittle failure of the specimen. The KJc values show a remarkable scatter. The highest T0 was about 50°C at a distance of 22 mm from the inner surface of the weld. The Charpy transition temperature TT41J estimated with results of subsized specimens after the recovery annealing was confirmed by the testing of standard Charpy V-notch specimens. The VERLIFE procedure prepared for the integrity assessment of WWER RPV was applied on the measured results. The VERLIFE lower bound curve indexed with the Structural Integrity Assessment Procedures for European Industry (SINTAP) reference temperature, RTT0SINTAP, envelops the KJc values. Therefore for a conservative integrity assessment the fracture toughness curve indexed with a RT representing the brittle fraction of a data set of measured KJc values has to be applied.

Applicability of Miniature C(T) Specimen to Evaluation of Fracture Toughness for Reactor Pressure Vessel Steel

2013 ◽  
Author(s):  
Kentaro Yoshimoto ◽  
Takatoshi Hirota ◽  
Hiroyuki Sakamoto ◽  
Takuji Sugihara ◽  
Shohei Sakaguchi ◽  
...  
Keyword(s):  
Fracture Toughness ◽  
Evaluation Method ◽  
Pressure Vessels ◽  
Charpy Specimen ◽  
Pressure Vessel Steel ◽  
Fracture Toughness Test ◽  
Irradiation Embrittlement ◽  
Vessel Steel ◽  
Reactor Pressure Vessel Steel ◽  
Reactor Pressure

Irradiation embrittlement of Japanese reactor pressure vessels (RPV) is usually monitored by conducting tests on irradiated RPV material according to surveillance test program. Although fracture toughness specimens are contained in Japanese PWR surveillance capsule, the number of specimens is limited due to capacity of capsule. In order to evaluate lower bound of fracture toughness considering its scatter with higher reliability, it is expected to obtain additional fracture toughness data using remaining broken specimens of irradiated materials. One of solutions to this problem is specimen reconstitution technique. However, it is difficult to make numbers of specimens by reconstitution because of need for specific equipments and time-consuming machining operations. As an alternative method, fracture toughness test using miniature C(T) specimens with dimension of 4×10×10mm, which can be taken from broken halves of Charpy specimen, is proposed and the studies to verify the reliability and robustness of evaluation method have been conducted in the Japanese round robin program since 2010. In this study, fracture toughness tests were performed on Japanese SA 533 Gr.B Cl.1 steel using miniature C(T) specimens and the effect of specimen size on reference temperature T0 was studied by the Master Curve approach. In addition, the issues related to application to irradiated materials were discussed.

Sign in / Sign up

Export Citation Format

Share Document