Volume Fraction Detection of Long Period Stacking Ordered Phases in Mg Alloys Based on Dual-Tree Complex Wavelet Packet Transform

2021 ◽  
Vol 57 (4) ◽  
pp. 281-290
Author(s):  
Xianghong Wang ◽  
Sheng Yang ◽  
Xiaojie Zhou ◽  
Hongwei Hu
2004 ◽  
Vol 17 (S1) ◽  
pp. 117-122 ◽  
Author(s):  
Zhou-min Xie ◽  
En-fu Wang ◽  
Guo-hong Zhang ◽  
Guo-cun Zhao ◽  
Xu-geng Chen

Metals ◽  
2019 ◽  
Vol 9 (2) ◽  
pp. 221 ◽  
Author(s):  
Gerardo Garces ◽  
Pablo Pérez ◽  
Rafael Barea ◽  
Judit Medina ◽  
Andreas Stark ◽  
...  

The evolution of the microstructure and mechanical properties during equal channel angular pressing processing has been studied in an extruded Mg-Gd-Y-Zn alloy containing long-period stacking ordered phases. After extrusion, the microstructure is characterized by the presence of long-period stacking ordered fibers elongated along the extrusion direction within the magnesium matrix. The grain structure is a mixture of randomly oriented dynamic recrystallized and coarse highly oriented non-dynamic recrystallized grains. Rare-earth atoms are in solid solution after extrusion at 400 °C and precipitation takes place during the thermal treatment at 200 °C. Precipitation of β’ prismatic plates and lamellar γ’ in the basal plane increases the tensile yield stress from 325 to 409 MPa. During equal channel angular pressing processing at 300 °C, the volume fraction of dynamic recrystallized grains continuously increases with the strain introduced during the equal channel angular pressing process. Precipitation of β phase is equally observed at grain boundaries of the ECAPed alloy. Dynamic recrystallized grain size decreases from 1.8 µm in the extruded material to 0.5 µm in the ECAPed alloy. Thermal treatment at 200 °C of ECAPed materials results in an increase of the yield stress up to 456 MPa, which is maintained up to 200 °C.


2011 ◽  
Vol 2011.60 (0) ◽  
pp. _257-1_-_257-2_
Author(s):  
Takeshi Kato ◽  
Zhong Zhang ◽  
Hiroshi Toda ◽  
Takashi Imamura ◽  
Tetsuo Miyake

2020 ◽  
Vol 2020 ◽  
pp. 1-18
Author(s):  
Wuqiang Liu ◽  
Xiaoqiang Yang ◽  
Shen Jinxing

The health condition of rolling bearings, as a widely used part in rotating machineries, directly influences the working efficiency of the equipment. Consequently, timely detection and judgment of the current working status of the bearing is the key to improving productivity. This paper proposes an integrated fault identification technology for rolling bearings, which contains two parts: the fault predetection and the fault recognition. In the part of fault predetection, the threshold based on amplitude-aware permutation entropy (AAPE) is defined to judge whether the bearing currently has a fault. If there is a fault in the bearing, the fault feature is adequately extracted using the feature extraction method combined with dual-tree complex wavelet packet transform (DTCWPT) and generalized composite multiscale amplitude-aware permutation entropy (GCMAAPE). Firstly, the method decomposes the fault vibration signal into a set of subband components through the DTCWPT with good time-frequency decomposing capability. Secondly, the GCMAAPE values of each subband component are computed to generate the initial candidate feature. Next, a low-dimensional feature sample is established using the t-distributed stochastic neighbor embedding (t-SNE) with good nonlinear dimensionality reduction performance to choose sensitive features from the initial high-dimensional features. Afterwards, the featured specimen representing fault information is fed into the deep belief network (DBN) model to judge the fault type. In the end, the superiority of the proposed solution is verified by analyzing the collected experimental data. Detection and classification experiments indicate that the proposed solution can not only accurately detect whether there is a fault but also effectively determine the fault type of the bearing. Besides, this solution can judge the different faults more accurately compared with other ordinary methods.


Author(s):  
TAKESHI KATO ◽  
ZHONG ZHANG ◽  
HIROSHI TODA ◽  
TAKASHI IMAMURA ◽  
TETSUO MIYAKE

In this paper, we propose a design method for directional selection in the two-dimensional complex wavelet packet transform (2D-CWPT). Current two-dimensional complex discrete wavelet transforms (2D-CDWT) can extract directional components from images, but the number of directions is small, and the directions and resolutions are fixed. Thus the current 2D-CDWTs are not flexible enough. In this study, we propose a new design method of the directional filters that can detect desirable direction components. Additionally flexible directional selection is achieved because the directional filters are added to the 2D-CWPT. Finally, the proposed method is applied to defect detection in semiconductor wafer circuits and an encouraging result is obtained.


Sign in / Sign up

Export Citation Format

Share Document