Contact-layer method in adhesive mechanics: Adhesive strength during normal detachment

2010 ◽  
Vol 3 (3) ◽  
pp. 159-169 ◽  
Author(s):  
R. A. Turusov ◽  
L. I. Manevich
2010 ◽  
Vol 3 (1) ◽  
pp. 1-9 ◽  
Author(s):  
R. A. Turusov ◽  
L. I. Manevich

Vestnik MGSU ◽  
2016 ◽  
pp. 17-26 ◽  
Author(s):  
Vladimir Igorevich Andreev ◽  
Robert Alekseevich Turusov ◽  
Nikita Yur’evich Tsybin

The article deals with the solution for the stress-strain state of a multilayer composite beam with rectangular cross-section, which is bended by normally distributed load. The intermolecular interaction between layers is accomplished by the contact layer, in which the substances of adhesive and substrate are mixed. We consider the contact layer as a transversal anisotropic medium with such parameters that it can be represented as a set of short elastic rods, which are not connected to each other. For simplicity, we assume that the rods are normally oriented to the contact surface. The contact layer method allows us to solve the problem of determining the concentration of tangential stresses arising at the boundaries between the layers and the corner points, their changes, as well as to determine the physical properties of the contact layer basing on experimental data. Resolving the equations obtained in this article can be used for the solution of many problems of the theory of layered substances. These equations were derived from the fundamental laws of the theory of elasticity and generally accepted hypotheses of the theory of plates for the general case of the bending problem of a multilayer beam with any number of layers. The article deals with the example of the numerical solution of the problem of bending of a three-layer beam. On the basis of this solution the curves were obtained, which reflect the stress-strain state of one of the layers. All these curves have a narrow area of the edge effect. The edge effect is associated with a large gradient tangential stresses in the contact layer. The experimental data suggest that in this zone the destruction of the samples occurs. This fact allows us to say that the equations obtained in this article can be used to construct a theory of the strength layered beams under bending.


2017 ◽  
Vol 117 ◽  
pp. 00008 ◽  
Author(s):  
Vladimir Andreev ◽  
Robert Turusov ◽  
Nikita Tsybin
Keyword(s):  

Author(s):  
N. David Theodore ◽  
Andre Vantomme ◽  
Peter Crazier

Contact is typically made to source/drain regions of metal-oxide-semiconductor field-effect transistors (MOSFETs) by use of TiSi2 or CoSi2 layers followed by AI(Cu) metal lines. A silicide layer is used to reduce contact resistance. TiSi2 or CoSi2 are chosen for the contact layer because these silicides have low resistivities (~12-15 μΩ-cm for TiSi2 in the C54 phase, and ~10-15 μΩ-cm for CoSi2). CoSi2 has other desirable properties, such as being thermally stable up to >1000°C for surface layers and >1100°C for buried layers, and having a small lattice mismatch with silicon, -1.2% at room temperature. During CoSi2 growth, Co is the diffusing species. Electrode shorts and voids which can arise if Si is the diffusing species are therefore avoided. However, problems can arise due to silicide-Si interface roughness (leading to nonuniformity in film resistance) and thermal instability of the resistance upon further high temperature annealing. These problems can be avoided if the CoSi2 can be grown epitaxially on silicon.


Author(s):  
Minakhi Pujari ◽  
Joachim Frank

In single-particle analysis of macromolecule images with the electron microscope, variations of projections are often observed that can be attributed to the changes of the particle’s orientation on the specimen grid (“rocking”). In the multivariate statistical analysis (MSA) of such projections, a single factor is often found that expresses a large portion of these variations. Successful angle calibration of this “rocking factor” would mean that correct angles can be assigned to a large number of particles, thus facilitating three-dimensional reconstruction.In a study to explore angle calibration in factor space, we used 40S ribosomal subunits, which are known to rock around an axis approximately coincident with their long axis. We analyzed micrographs of a field of these particles, taken with 20° tilt and without tilt, using the standard methods of alignment and MSA. The specimen was prepared with the double carbon-layer method, using uranyl acetate for negative staining. In the MSA analysis, the untilted-particle projections were used as active, the tilted-particle projections as inactive objects. Upon tilting, those particles whose rocking axes are parallel to the tilt axis will change their appearance in the same way as under the influence of rocking. Therefore, each vector, in factor space, joining a tilted and untilted projection of the same particle can be regarded as a local 20-degree calibration bar.


2020 ◽  
Author(s):  
Soumi Haldar ◽  
Achintya Kumar Dutta

We have presented a multi-layer implementation of the equation of motion coupled-cluster method for the electron affinity, based on local and pair natural orbitals. The method gives consistent accuracy for both localized and delocalized anionic states. It results in many fold speedup in computational timing as compared to the canonical and DLPNO based implementation of the EA-EOM-CCSD method. We have also developed an explicit fragment-based approach which can lead to even higher speed-up with little loss in accuracy. The multi-layer method can be used to treat the environmental effect of both bonded and non-bonded nature on the electron attachment process in large molecules.<br>


Sign in / Sign up

Export Citation Format

Share Document