Recovery of Small-Strain Stiffness Following Blast-Induced Liquefaction Based on Shear Wave Velocity Measurements

2020 ◽  
Author(s):  
Siavash Mahvelati ◽  
Joseph Thomas Coe ◽  
Armin W. Stuedlein ◽  
Philip Asabere ◽  
Tygh Gianella ◽  
...  
Keyword(s):  
South Carolina ◽  
Shear Wave ◽  
Wave Velocity ◽  
Shear Wave Velocity ◽  
Small Strain ◽  
Rate Variation ◽  
Time Rate ◽  
Small Strain Stiffness ◽  
Soil Fabric

Changes in soil fabric following liquefaction have been studied using various in-situ methods, and often return inconclusive or conflicting observations. The time-rate variation of stiffness, when observed, is usually not evaluated over significant periods of time, limiting investigations about aging in post-liquefaction regain of stiffness. Even more uncommon is the application of geophysical techniques to evaluate changes in shear wave velocity (VS) as a proxy for small-strain stiffness. This study uses controlled blasting to examine long-term post-liquefaction regain of stiffness following multiple blast events. The Multichannel Analysis of Surface Waves (MASW) technique was used to observe changes in VS of aged deposits at a test site in South Carolina. Blast-induced liquefaction of the target liquefiable layer resulted in significant reduction to its initial small-strain stiffness owing to the destruction of the aged soil fabric. The time-rate variation in VS indicated that the initial small-strain stiffness was not re-established over many months following liquefaction. Following a second blast event, the small-strain stiffness reduced again, but recovered more quickly, similar to previously reported observations of young sand deposits. This study provides a significant basis for interpreting in-situ body and surface wave measurements of aged and young sand deposits densified using blast liquefaction.

scholarly journals In situ shear wave velocity from multichannel analysis of surface waves (MASW) tests at eight Norwegian research sites

2007 ◽  
Vol 44 (5) ◽  
pp. 533-544 ◽  
Author(s):  
Michael Long ◽  
Shane Donohue
Keyword(s):  
Surface Waves ◽  
Shear Wave ◽  
Wave Velocity ◽  
Shear Wave Velocity ◽  
Small Strain ◽  
Soft Clays ◽  
Small Strain Stiffness ◽  
Wave Measurements ◽  
Multichannel Analysis

The multichannel analysis of surface waves (MASW) technique, which is used to determine shear wave velocity (Vs) and hence small strain stiffness (Gmax), has recently generated considerable interest in the geophysics community. This is because of the ease of carrying out the test and analysis of the data. The objective of this work was to assess the repeatability, accuracy, and reliability of MASW surface wave measurements for use in engineering studies. Tests were carried out at eight well-characterized Norwegian clay, silt, and sand research sites where Vs had already been assessed using independent means. As well as being easy and quick to use, the MASW technique gave consistent and repeatable results, and the MASW Vs profiles for the clay sites were similar to those obtained from other techniques. Reasonable results were also obtained for the silt and sand sites, with the best result being obtained for the finer silt. This work also confirms that MASW Vs clay profiles are comparable to those obtained by correlation with cone penetration test (CPT) data. For these sites there also seems to be a good correlation between normalized small strain shear modulus and in situ void ratio or water content, and the data fit well with published correlations for clays.Key words: soft clays, silts, sands, small strain stiffness, shear wave velocity.

Small-Strain Stiffness, Shear-Wave Velocity, and Soil Compressibility

2014 ◽  
Vol 140 (10) ◽  
pp. 06014011 ◽  
Author(s):  
Minsu Cha ◽  
J. Carlos Santamarina ◽  
Hak-Sung Kim ◽  
Gye-Chun Cho
Keyword(s):  
Shear Wave ◽  
Wave Velocity ◽  
Shear Wave Velocity ◽  
Small Strain ◽  
Small Strain Stiffness ◽  
Soil Compressibility

scholarly journals Small strain stiffness in overconsolidated Pliocene clays

2013 ◽  
Vol 45 (2) ◽  
pp. 169-181 ◽  
Author(s):  
Katarzyna Markowska-Lech ◽  
Mariusz Lech ◽  
Marek Bajda ◽  
Alojzy Szymański
Keyword(s):  
Shear Modulus ◽  
Shear Wave ◽  
Wave Velocity ◽  
Shear Wave Velocity ◽  
Cohesive Soil ◽  
Small Strain ◽  
Soil Parameters ◽  
Small Strain Stiffness ◽  
Triaxial Apparatus ◽  
Triaxial Cell

Abstract Small strain stiffness in overconsolidated Pliocene clays. A huge development of technical infrastructure, including the construction of many high-rise buildings, roads, railroads and extension of subway lines, took place over the recent years in Poland. Therefore, numerous planned investment projects require geotechnical data documenting the variation of soil parameters found in the subsoil. The shear wave velocity is one of the most important input parameters to represent the stiffness of the soil deposits. This paper focuses on the methods and devices using measurements of the shear wave velocity to estimate the initial shear modulus in cohesive soil. It is preferable to measure VS by in situ wave propagation tests, however it is often economically not feasible in all regions of Poland. Hence, a reliable correlation between shear wave velocity and parameters measured in triaxial cell or static penetration parameters would be a considerable advantage. This study shows results obtained from the bender elements tests and field techniques - seismic cone penetration test and seismic flat dilatometer, performed on overconsolidated cohesive soils in Warsaw. On the basis of the test results possible correlations between shear wave velocity (initial shear modulus), mean effective stress and void ratio are considered and four original empirical relationships are proposed. Moreover, the proposed formulas by two different techniques using triaxial apparatus and also RCPT cone were examined. The proposed formulas show a reasonable agreement with direct shear wave velocity profiles for clays and might be incorporated into routine laboratory and field practice

Time-Rate Variation of the Shear Wave Velocity (Site Stiffness) Following Blast-Induced Liquefaction

2016 ◽  
Author(s):  
Siavash Mahvelati ◽  
Joseph T. Coe ◽  
Armin W. Stuedlein ◽  
Philip Asabere ◽  
Tygh N. Gianella
Keyword(s):  
Shear Wave ◽  
Wave Velocity ◽  
Shear Wave Velocity ◽  
Rate Variation ◽  
Time Rate

Soil Liquefaction Evaluation of Offshore Site Based on In Situ Shear Wave Velocity Measurements

2013 ◽  
Vol 405-408 ◽  
pp. 470-473
Author(s):  
Sheng Jie Di ◽  
Ming Yuan Wang ◽  
Zhi Gang Shan ◽  
Hai Bo Jia
Keyword(s):  
Shear Wave ◽  
Wave Velocity ◽  
Shear Wave Velocity ◽  
Wind Farm ◽  
Soil Liquefaction ◽  
Offshore Wind ◽  
Velocity Measurements ◽  
Liquefaction Resistance ◽  
Liquefaction Potential

A procedure for evaluating liquefaction resistance of soils based on the shear wave velocity measurements is outlined in the paper. The procedure follows the general formal of the Seed-Idriss simplified procedure. In addition, it was developed following suggestions from industry, researchers, and practitioners. The procedure correctly predicts moderate to high liquefaction potential for over 95% of the liquefaction case histories. The case study for the site of offshore wind farm in Jiangsu province is provided to illustrate the application of the proposed procedure. The feature of the soils and the shear wave velocity in-situ tested in site are discussed and the liquefaction potential of the layer is evaluated. The application shows that the layers of the non-cohesive soils in the depths 3-11m may be liquefiable according to the procedure.

scholarly journals CHARACTERIZING A TROPICAL SOIL VIA SEISMIC IN SITU TESTS

2019 ◽  
Vol 37 (3) ◽  
pp. 263
Author(s):  
Breno Padovezi Rocha ◽  
Heraldo Luiz Giacheti
Keyword(s):  
Shear Modulus ◽  
Shear Wave ◽  
Wave Velocity ◽  
Shear Wave Velocity ◽  
Soil Profile ◽  
Site Investigation ◽  
Tropical Soil ◽  
Engineering Properties ◽  
Foundation Engineering

ABSTRACT. The shear wave velocity (Vs) is an important geotechnical parameter to be used in dynamic problems (e.g. earthquakes and vibration problems) as well as in static deformation analysis such as excavations and foundation engineering design. There are several in situ seismic tests to determine Vs such as the crosshole and the downhole techniques, as well as hybrid tests (e.g. seismic dilatometer – SDMT). This paper presents crosshole, downhole and SDMT tests carried out in a typical tropical soil profile from Brazil. Advantages and limitations regarding the test procedures and interpretation are briefly presented and differences observed among Vs determined by these techniques are discussed. Shear wave velocities (Vs) estimated from the crosshole, downhole and SDMT tests ranging from 194 to 370 m/s. The shear wave velocity suggests that the experimental site could be divided into two strata, which are in agreement with soil profile description. The maximum shear modulus (G0) calculated from the Vs by theory of elasticity can be used to show the investigated tropical soil is a typical unusual geomaterial. This article also emphasizes that the SDMT is a useful test for site investigation since it allows a great means for profiling geostratigraphy and soil engineering properties during routine site investigation as well as for dynamics problems. Keywords: shear wave velocity, maximum shear modulus, crosshole, downhole, SDMT.RESUMO. A velocidade de onda cisalhante (Vs) é um parâmetro geotécnico empregado em análises dinâmicas (terremotos e problemas de vibração), bem como em análises estáticas (escavações e projeto de fundações). Existem vários ensaios sísmicos de campo para a determinação de Vs, entre eles as técnicas crosshole e downhole, e os ensaios híbridos (por exemplo, dilatômetro sísmico – SDMT). Este artigo apresenta os ensaios crosshole, downhole e SDMT realizados em um perfil típico de solo tropical do Brasil, as vantagens e limitações dos procedimentos de ensaio e de interpretação são brevemente apresentadas, e as diferenças observadas entre os valores de Vs determinados pelas diferentes técnicas são discutidas. Os perfis de Vs determinados pelas diferentes técnicas variaram de 194 a 370 m/s. A velocidade da onda cisalhante sugere que o campo experimental investigado pode ser dividido em dois horizontes, os quais estão de acordo com a descrição do perfil do solo estudado. O módulo de cisalhamento máximo (G0), calculado a partir de Vs pela teoria da elasticidade, pode ser utilizado para demonstrar o comportamento não convencional do solo investigado. Este artigo também enfatiza que o SDMT é um ensaio geotécnico útil para a investigação geotécnica do subsolo, uma vez que permite a definição do perfil estratigráfico e a estimativa de parâmetros estáticos e dinâmicos de um projeto.Palavras-chave: velocidade de onda cisalhante, módulo de cisalhamento máximo, crosshole, downhole, SDMT.

Critical Insights in Laboratory Shear Wave Velocity Correlations of Clays

2021 ◽  
Author(s):  
Dania Elbeggo ◽  
Yannic Ethier ◽  
Jean-Sébastien Dubé ◽  
Mourad Karray
Keyword(s):  
Shear Wave ◽  
Wave Velocity ◽  
Shear Wave Velocity ◽  
Earth Pressure ◽  
Dynamic Parameter ◽  
Clay Deposits ◽  
Sample Disturbance ◽  
P Rat

Shear wave velocity is an important mechanical/dynamic parameter allowing the characterization of a soil in the elastic range (γ < 0.001 %). Thirty five existing laboratory correlations of small strains shear modulus or shear wave velocity were examined in this study and are grouped into different general forms based on their geotechnical properties. A database of 11 eastern Canadian clay deposits was selected and used for the critical insights. The effect of the coefficient of earth pressure at rest was also examined. A range of variation for each general form of correlation was determined to take the plasticity index and void ratio values of investigated sites into account. The analysis shows a significant scatter in normalized shear wave velocity values predicted by existing correlations and raises questions on the applicability of these correlations, especially for eastern Canadian clays. New correlations are proposed for Champlain clays based on laboratory measurement of shear wave velocity using the piezoelectric ring actuator technique, P-RAT, incorporated in consolidation cells. An analysis of P-RAT results reveals the sample disturbance effect and suggests an approach to correct the effect of disturbance on laboratory shear wave velocity measurements. The applicability of the proposed correlations, including the disturbance correction, is validated by comparison with in situ measurements using multi-modal analysis of surface waves (MMASW).

In Situ Shear-Wave Velocity Assessment at the Delaney Park Downhole Array, Anchorage, Alaska

2020 ◽  
Vol 91 (6) ◽  
pp. 3381-3390
Author(s):  
Hai-Yun Wang ◽  
Wei-Ping Jiang
Keyword(s):  
Shear Wave ◽  
Wave Velocity ◽  
Shear Wave Velocity ◽  
Great Influence ◽  
Standard Penetration Test ◽  
Weak Anisotropy ◽  
Near Surface ◽  
Motion Data ◽  
Downhole Array

Abstract The shear-wave velocity (VS) in soil is an important parameter to characterize dynamic soil properties. The Delaney Park downhole array was deployed in 2003 without measuring the shear- and compression-wave velocity (VS and VP) profiles. Thornley et al. (2019) measured the VS and VP profiles using the downhole method after the sensor was removed from the 61 m borehole with casing in the array. However, the waves propagating along the casing wall may have a great influence on the recognition of the first arrival of waves propagating in the soil. Using horizontal and vertical components of weak-motion data of eight local earthquakes recorded by the array, in situ VS and VP profiles were assessed by the seismic interferometry based on deconvolution, respectively. The results are as follows. The VS and VP profiles computed by this study and measured by Thornley et al. (2019) are in relatively good agreement at a depth of 10–45 m and at a depth of 30–45 m, respectively, and in very poor agreement at other depths. The average VS profiles computed by this study are more consistent with the derived VS from the standard penetration test data at the site with slower near-surface velocities relative to the downhole logging analysis. There are strong anisotropy in the strata below 45 m and weak anisotropy with various degrees at various depths in the strata above 45 m.

Sign in / Sign up

Export Citation Format

Share Document