scholarly journals Point Load Test of Half-Cylinder Core Using the Numerical Model and Laboratory Tests: Size Suggestion and Correlation with Cylinder Core

2018 ◽  
Vol 2018 ◽  
pp. 1-11 ◽  
Author(s):  
Fengyu Ren ◽  
Huan Liu ◽  
Rongxing He ◽  
Guanghui Li ◽  
Yang Liu
Keyword(s):  
Numerical Model ◽  
Laboratory Tests ◽  
Failure Load ◽  
Field Tests ◽  
Point Load ◽  
Diameter Ratio ◽  
Load Test ◽  
Index Test ◽  
Point Load Test ◽  
Calculation Procedures

The point load test (PLT) is intended as an index test for rock strength classification or estimations of other strength parameters because it is economical and simple to conduct in the laboratory and in field tests. In the literature, calculation procedures for cylinder cores, blocks, or irregular lumps can be found, but no study has researched such procedures for half-cylinder cores. This paper presents the numerical model and laboratory tests for half-cylinder and cylinder specimens. The results for half-cylinder and cylinder specimens are then presented, analysed, and discussed. A correlation of failure load between half-cylinder and cylinder specimens is established with a suitable size suggestion and correction factor. It is found that the failure load becomes stable when half-cylinder specimens have a length/diameter ratio higher than 0.9. In addition, the results show that the point load strength index (PLSI) of half-cylinder cores can be calculated using the calculation procedures for diametral testing on cylinder cores, and it is necessary to satisfy the conditions that the length/diameter ratio be higher than 0.9 and the failure load be multiplied by 0.8.

scholarly journals Characterization of rock material by point load strength index test and direct cut

Minerva ◽  
2021 ◽  
Vol 2 (4) ◽  
pp. 11-22
Author(s):  
Ernesto Patricio Feijoo Calle ◽  
Paúl Andrés Almache Rodríguez
Keyword(s):  
Point Load ◽  
Strength Test ◽  
Load Test ◽  
Index Test ◽  
Strength Index ◽  
Point Load Strength ◽  
Point Load Strength Index ◽  
Point Load Test ◽  
Engineering Sciences ◽  
Cutting Point

The objective of this work is to establish a relationship between the cutting time in rocks, determining a speed and the point load strength index test, Is (50), to characterize the rock in terms of resistance and avoid sending samples to laboratories. As a first stage, on andesite samples, 5 x 5 x 10 cm test tubes were made. After the elaboration they were subjected to cutting, using an electric floor cutter and the time was evaluated. This cut was made in a transversal way and two parts were obtained, one of them with dimensions 5 x 5 x 5 cm, approximately. In a third stage, the point load strength test was carried out in a press built for this purpose. Finally, the cutting speeds were correlated with the point load test values and only when rock samples do not pigeonhole on the proposed relationship, send them to the laboratory. Keywords: Mining fortification, uniaxial compressive strength, rock cutting, point load strength test index. References [1]P. Feijoo, R. Aucay, D. Ordoñez, "Aplicación del esclerómetro para la determinación de resistencia a compresión de rocas", presentado en el IV Congreso Internacional de Minería y Metalúrgia (MINEMETAL), Varadero, Cuba, 2018. [2]P. Feijoo y M. Román, «Correlación entre la Deformación y la Resistencia a la Compresión de rocas», uct, vol. 23, n.º 91, p. 6, may. 2019. [3]P. Feijoo, A. Bravo, N. Escandón, "Aplicación “UDAFORMIN” para la determinación del tipo de fortificación minera", presentado en el XII Congreso Iberoamericano de Computación para el Desarrollo (COMPDES), San Salvador, El Salvador, 2019. [4]P. Feijoo y C. Iñiguez, «Corte en las Rocas y su Relación con la Resistencia a Comprensión Simple», RISTI, n.º E 30, p. 59-67, jun. 2020. [5]P. Feijoo y J. Padrón, «La Resistividad de Rocas y su Relación con la Resistencia a Comprensión Simple en Mina», UCT, vol. 24, n.º 99, pp. 61-67, abr. 2020. [6]M. González. El terreno. Ediciones UPC. Barcelona. España, 2001. [7]E. Besoain. Mineralogía de Suelos. Turrialba: Instituto Interamericano de Ciencias Agrícolas de la OEA, 1970. [8]P. Feijoo, A. Flores, B. Feijoo, "The Concept of the Granulometric Area and Its Relation with the Resistance to the Simple Compression of Rocks", presentado en la 7th International Engineering, Sciences and Technology Conference (IESTEC), Panamá, Panamá, 2019, pp. 52-56, doi: 10.1109/IESTEC46403.2019.00018. [9]F. Blyth. Geología para Ingenieros. Cecsa. México D. F. México, 2003. [10] E. Tarbuck & F. Lutgens. Ciencias de la Tierra: Una introducción a la Geología Física. Pearson. Madrid. España, 2005. [11]L. Suarez del Rio, A. Rodríguez, L. Calleja, V. Ruiz de Argandoña, «El corte de rocas ornamentales con discos diamantados: influencia de los factores propios del sistema de corte», CSIC, vol. 48, n.º 250, pp. 53-59, abr-mayjun 1998. [12]Universidad Politécnica de Madrid. Explotaciones de Roca Ornamental. Diseño de explotaciones y selección de maquinaria y equipos. UPM. Madrid. España, 2007. [13]Catalog, Covington, (2019). LAPIDARY & GLASS MACHINERY, USA. Retrieved from https://covington-engineering.com/content/pdf/Covington-Catalog.pdf. [14]D. Burbano, T. García, «Estimación empírica de la resistencia a compresión simple a partir del ensayo de carga puntual en rocas anisótropas (esquistos y pizarras)», FIGEMPA, vol.1, n.º 2, pp. 13-16, dic. 2016. [15]P. Ramírez, L. de la Cuadra, R. Lain, E. Grigalbo. Mecánica de rocas aplicada a la minería metálica subterránea. Instituto Geológico Minero. Madrid. España, 1984. [16]P. Cordero, "Manual de prácticas de laboratorio de Mecánica de Rocas (Parte I)" tesis, Universidad Nacional Autónoma de México, México D.F., México, 2019. [17]L. González de Vallejo, M. Ferrer. Manual de campo para la descripción y caracterización de macizos rocosos en afloramientos. Instituto Geológico y Minero de España. Madrid. España, 2007. [18]P. Pohjanpera, T. Wanne, E., Johansson. Point Load Test Results From Olkiluoto Area Borehole Cores. Posiva. Finlandia, 2005. [19]P. Ramírez, L. Alejano. Mecánica de rocas: fundamentos e ingeniería de taludes. Universidad Politécnica de Madrid. Madrid. España, 2004. [20]M. Navarrete, W. Martínez, E. Alonso, C. Lara, A. Bedolla, H. Chávez, D. Delgado, J. Arteaga. «Caracterización de propiedades físico-mecánicas de rocas ígneas utilizadas en obras de infraestructura», ALCONPANT, vol. 3, n.º 2, pp. 133-143, ago. 2013. [21]P. Feijoo, "Manual de mecánica de rocas y estabilidad de túneles y taludes" tesis, Universidad del Azuay, Cuenca, Ecuador, 1997.    

Analysis of point load test as a method for preliminary geotechnical classification of rocks

1973 ◽  
Vol 7 (1) ◽  
pp. 37-52 ◽  
Author(s):  
Guidicini G. ◽  
C. M. Nieble ◽  
A. T. Cornides
Keyword(s):  
Point Load ◽  
Load Test ◽  
Point Load Test

A New, Highly Portable Point Load Test Device for Extreme Field Areas

2007 ◽  
Vol 13 (1) ◽  
pp. 69-73 ◽  
Author(s):  
S. D. BOWMAN ◽  
R. J. WATTERS
Keyword(s):  
Point Load ◽  
Load Test ◽  
Test Device ◽  
Point Load Test

Using the Point Load Test to Analyze the Strength Anisotropy of Quartz Mica Schist Along an Exploration Adit

2015 ◽  
Vol 49 (5) ◽  
pp. 1967-1975 ◽  
Author(s):  
Xiao-Ping Zhang ◽  
Shunchuan Wu ◽  
Lekan Olatayo Afolagboye ◽  
Sijing Wang ◽  
Gengyou Han
Keyword(s):  
Point Load ◽  
Load Test ◽  
Strength Anisotropy ◽  
Mica Schist ◽  
Point Load Test

A Interpretação dos Resultados do Point-Load Test - Mineração Serra Grande - AngloGold Ashanti

2016 ◽  
Author(s):  
Davi Newton Pinheiro da Costa Gomes
Keyword(s):  
Point Load ◽  
Load Test ◽  
Point Load Test
Sign in / Sign up

Export Citation Format

Share Document