scholarly journals Influence of Oxidation Damages on Mechanical Properties of SiC/SiC Composite Using Domestic Hi-Nicalon Type SiC Fibers

Scanning ◽  
2020 ◽  
Vol 2020 ◽  
pp. 1-8
Author(s):  
Enze Jin ◽  
Denghao Ma ◽  
Zeshuai Yuan ◽  
Wenting Sun ◽  
Hao Wang ◽  
...  
Keyword(s):  
Tensile Strength ◽  
Tensile Modulus ◽  
Treatment Temperature ◽  
Matrix Interface ◽  
Oxidation Treatment ◽  
Pull Out ◽  
Special Surface ◽  
Higher Temperature ◽  
Fiber Matrix Interface ◽  
Fiber Matrix

Here, we show that when the oxidation treatment temperature exceeded 600°C, the tensile strength of SiC/SiC begins to decrease. Oxidation leads to the damages on the PyC fiber/matrix interface, which is replaced by SiO2 at higher temperature. The fracture mode converts from fiber pull-out to fiber-break as the fiber/matrix interface is filled with SiO2. Oxidation time also plays an important role in affecting the tensile strength of SiC/SiC. The tensile modulus decreases with temperature from RT to 800°C, then increases above 800°C due to the decomposition of remaining CSi x O y and crystallization of the SiC matrix. A special surface densification treatment performed in this study is confirmed to be an effective approach to reduce the oxidation damages and improve the tensile strength of SiC/SiC after oxidation.

scholarly journals Effect of Interface Coating on High Temperature Mechanical Properties of SiC–SiC Composite Using Domestic Hi–Nicalon Type SiC Fibers

Coatings ◽  
2020 ◽  
Vol 10 (5) ◽  
pp. 477 ◽  
Author(s):  
Enze Jin ◽  
Wenting Sun ◽  
Hongrui Liu ◽  
Kun Wu ◽  
Denghao Ma ◽  
...  
Keyword(s):  
Tensile Strength ◽  
High Temperature ◽  
Theoretical Analysis ◽  
Fracture Mode ◽  
Radial Stress ◽  
Matrix Interface ◽  
Preparation Temperature ◽  
Pull Out ◽  
Fiber Matrix Interface ◽  
Fiber Matrix

Here we show that when the temperature exceeded 1200 °C, the tensile strength drops sharply with change of fracture mode from fiber pull-out to fiber-break. Theoretical analysis indicates that the reduction of tensile strength and change of fracture mode is due to the variation of residual radial stress on the fiber–matrix interface coating. When the temperature exceeds the preparation temperature of the composites, the residual radial stress on the fiber–matrix interface coating changes from tensile to compressive, leading to the increase of the interface strength with increasing temperature. The fracture behavior of SiC–SiC composites changes from ductile to brittle when the strength of fiber–matrix interface coating exceeds the critical value. Theoretical analysis predicts that the high temperature tensile strength can increase with a decrease in fiber–matrix interface thickness, which is verified by experiments.

In situ determination of the fiber–matrix interface tensile strength

2015 ◽  
Vol 50 (5) ◽  
pp. 589-599 ◽  
Author(s):  
Kyle R Totten ◽  
Bender Kutub ◽  
Leif A Carlsson
Keyword(s):  
Tensile Strength ◽  
Matrix Interface ◽  
Fiber Matrix Interface ◽  
Fiber Matrix

The Effect of Thermal Aging on Tensile Strength of Three-Dimension and Five-Direction Braided Carbon Fiber/BMI Composites

2010 ◽  
Vol 150-151 ◽  
pp. 1139-1142
Author(s):  
Qi Wei Guo ◽  
Jia Lu Li ◽  
Guo Li Zhang ◽  
Ye Hong He ◽  
Ming Zhang ◽  
...  
Keyword(s):  
Tensile Strength ◽  
Carbon Fiber ◽  
Thermal Aging ◽  
Testing Machine ◽  
Tensile Load ◽  
Three Dimension ◽  
Matrix Interface ◽  
Fiber Matrix Interface ◽  
Fiber Matrix ◽  
Universal Material Testing Machine

This work aims at investigating the effect of thermal aging on tensile properties of three-dimension (3D) and five-direction braided carbon fiber/BMI resin composites prepared by resin transfer molding (RTM) process. The influence of high temperature on the tensile strength and the failure mechanisms of un-aged and aged composites were studied, respectively. As for the thermal aging condition, 180 for 24h was selected. The tensile strength of both un-aged and aged specimens were tested by SHIMADZU universal material testing machine at room temperature. The fracture modes of specimens were observed by scanning electron microscopy (SEM). It was found that the tensile load at break and tensile strength decreased after ageing. From the SEM views of the failed samples, the fracture surface presented hackles which were specific to the debonding of the interface between fibers and matrix. A lot of fibers were pulled-out in the aged state specimen. It can be confirmed that the failure occurred at the fiber/matrix interface and the fiber/matrix interface seemed to be weak in aged carbon fabrics reinforced BMI composites.

scholarly journals Surface roughness characterization of various ceramic fibers using AFM and low-voltage SEM

1994 ◽  
Vol 52 ◽  
pp. 1066-1067
Author(s):  
K. L. More ◽  
E. Lara-Curzio ◽  
R. A. Lowden
Keyword(s):  
Surface Roughness ◽  
Low Voltage ◽  
Interfacial Shear Stress ◽  
Fiber Surface ◽  
Interfacial Properties ◽  
Matrix Interface ◽  
Ceramic Fibers ◽  
Pull Out ◽  
Fiber Matrix Interface ◽  
Fiber Matrix

The effect of interfacial properties in fiber-reinforced ceramic matrix composites is critical to the overall mechanical behavior of the composite material. The creation of a relatively weak fiber/matrix interface allows for the beneficial actions of debonding and fiber pull-out to occur, thus improving the fracture toughness and, in many cases, the ultimate strength of the composite. To date, the best room temperature interfacial properties have been achieved by coating the fibers with either carbon or boron nitride. There are several factors which contribute to the interfacial properties of a composite, including the residual stress (clamping stress) present at the fiber/matrix interface, which is a result of differences in thermal expansion, and the fiber surface roughness. In this study, the surfaces of several ceramic fibers have been characterized qualitatively using a Hitachi S-4500 FEG SEM operated at low voltages and quantitatively using a Topometrix atomic force microscope (AFM). This study is part of an overall program relating fiber surface roughness to the interfacial shear stress.

Development of an Adhesion Test for Characterizing the Interface Fiber/Polymer Matrix

2012 ◽  
Vol 498 ◽  
pp. 210-218 ◽  
Author(s):  
Bouchra Hassoune-Rhabbour ◽  
Laurence Poussines ◽  
Valérie Nassiet
Keyword(s):  
Polymer Matrix ◽  
Composite Fiber ◽  
Matrix Interface ◽  
Pull Out ◽  
Structures And Properties ◽  
The Matrix ◽  
Fiber Matrix Interface ◽  
Fiber Matrix ◽  
Relationship Structures ◽  
The Relationship

There are several models on the relationship structures and properties of the composite fiber / matrix interface [1]. Including literature proposes the development of micromechanical tests suitable for assessing the shear strength of the interface fiber / polymer matrix. The first test which allowed to characterize the fiber / matrix interface is the pull-out test developed by Broutman [2]. It consists in extracting the fiber from the matrix that can be in block form, gout or disk of resin. To reduce the variation in results due to the geometries used, it was agreed to use a drop of resin with small dimensions. The test is to characterize the fiber / matrix interface of natural thermosetting or thermoplastic by determining the shear stress.

The Influence of Heat Treatment upon Fiber Pull-Out in a Ceramic Composite

1988 ◽  
Vol 120 ◽  
Author(s):  
M. D. Thouless ◽  
O. Sbaizero ◽  
E. Bischoff ◽  
E. Y. Luh
Keyword(s):  
Ceramic Composite ◽  
Ceramic Matrix Composites ◽  
Matrix Composites ◽  
Matrix Interface ◽  
Shear Lag ◽  
Weibull Statistics ◽  
Pull Out ◽  
Fiber Matrix Interface ◽  
Fiber Matrix

AbstractThe toughness of ceramic-matrix composites is strongly influenced by fiber pull-out. The extent of the pull-out depends upon the properties of the fiber and the fiber/matrix interface. Samples of a SiC/LAS composite were subjected to different heat treatments in order to systematically vary these properties. The predicted distribution of the fiber pull-out lengths was calculated by combining a shear lag analysis with Weibull statistics for the fiber strengths. Comparison of the analysis with experiments and microstructural observations contribute to an understanding of the role of the fiber/matrix interface upon the mechanical properties.

Effects of Seawater Immersion on Mechanical Properties of CFRP Composites

2013 ◽  
Vol 785-786 ◽  
pp. 209-213
Author(s):  
Qi Zhong Huang ◽  
Zhao Hui Hu
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Carbon Fiber ◽  
Water Absorption ◽  
Flexural Modulus ◽  
Tensile Modulus ◽  
Resin Matrix ◽  
Matrix Composites ◽  
Matrix Interface ◽  
Fiber Matrix Interface

Water absorption behavior and mechanical properties variation of the carbon fiber reinforced epoxy matrix composites (CFRP) immersed into artificial seawater were investigated by experiments. The rate of water absorption of the composite specimens is gradually reducing as the duality of immersion increasing. Due to the reversible and irreversible changes in the resin matrix and the failure of the fiber/matrix interface, the tensile strength, the flexural strength, and the ILSS of the composite specimens after 70 days immersion decreased 9.3%, 13%, and 17% respectively. And the tensile modulus and the flexural modulus the specimens after desorption were 83% and 70% of the original state, respectively

Nondestructive Characterization of Fiber-Matrix Adhesion in Composites by Vibration Damping

1995 ◽  
Vol 385 ◽  
Author(s):  
Weiqun Gu ◽  
Guo-Quan Lu ◽  
H. Felix Wu ◽  
Stephen L. Kampe ◽  
P. Ross Lichtenstein ◽  
...  
Keyword(s):  
Tensile Strength ◽  
Glass Fiber ◽  
Fiber Surface ◽  
Vibration Damping ◽  
Matrix Interface ◽  
Fiber Reinforced ◽  
Transverse Tensile ◽  
Fiber Matrix Interface ◽  
Fiber Matrix ◽  
Transverse Tensile Strength

ABSTRACTAdhesion at fiber-matrix interface in fiber-reinforced composites plays an important role in controlling the mechanical properties and overall performance of composites. Among the many available tests applicable to the composite interfaces, vibration damping technique has the advantages of being nondestructive as well as highly sensitive. We set up an optical system to measure the damping tangent delta of a cantilever beam, and correlated the damping data in glass-fiber reinforced epoxy-resin composites with transverse tensile strength which is also a qualitative measurement of adhesion at fiber-matrix interface. Four different composite systems containing three different glass-fiber surface treatments were tested and compared. Our experimental results showed an inverse relationship between damping contributed by the interface and composite transverse tensile strength.

Sign in / Sign up

Export Citation Format

Share Document