scholarly journals Numerical Simulation and Shear Capacity Study of a New Double-Steel-Plate Shear Wall

2021 ◽  
Vol 2021 ◽  
pp. 1-14
Author(s):  
Xiaomeng Zhang ◽  
Qingying Ren ◽  
Jiaqi Wang ◽  
Ziao Liu ◽  
Xiao Yang
Keyword(s):  
Finite Element ◽  
Goodness Of Fit ◽  
Steel Plate ◽  
Shear Wall ◽  
Shear Capacity ◽  
Practical Calculation ◽  
Test Results ◽  
Element Analysis ◽  
Steel Plate Shear Wall ◽  
Finite Element Software

This paper presents a new type of double-steel-plate shear wall. Through the finite element software, the stress and plastic strain of steel plate and concrete in different loading stages of the wall are analyzed, the mechanical properties and failure rules of the wall are revealed, and the failure mechanism of the wall is obtained. The comparison with the test results verifies the correctness of the finite element analysis. Through nonlinear finite element parameterization analysis, the composition of shear capacity of each composite wall is obtained. Based on the superposition theory, practical calculation formula of its shear capacity is given, and through a comparative analysis with simulation test results, the goodness-of-fit is satisfying.

scholarly journals Seismic Behavior of a Novel Buckling-Restrained Steel Plate Shear Wall

2021 ◽  
Vol 2021 ◽  
pp. 1-21 ◽  
Author(s):  
Yang Li ◽  
Xiaofeng Zhao ◽  
Ping Tan ◽  
Fulin Zhou ◽  
Jin Jiang
Keyword(s):  
Finite Element ◽  
Energy Dissipation ◽  
Finite Element Model ◽  
Steel Plate ◽  
Element Model ◽  
Shear Wall ◽  
Concrete Slabs ◽  
Test Results ◽  
Steel Plate Shear Wall ◽  
Hysteretic Characteristics

In this study, in a novel buckling-restrained steel plate shear wall (BRSPSW) with out-of-plane deformation spaces, angle steel stiffeners have been installed so as to create gaps between the steel plate and the covering concrete slabs. A finite element model has been developed to analyse the effect of the gap. According to the finite element results, seismic performance of this novel BRSPSW has been tested under cyclic loading at the scale ratio of 1/3. The failure pattern, hysteretic characteristics, skeleton curve, equivalent stiffness, ductility, and energy dissipation have all been systematically analysed. A stiffened steel plate shear wall (SPSW) has also been tested in order to determine the differences between these two steel shear walls in load-carrying capability and the function and significance of the gap. The test results show that the novel BRSPSW does not only significantly enhance the ultimate bearing capacity, stiffness, ductility, and accumulated energy dissipation of the SPSW but also keep the steel plate basically intact at the end of the test. This can be attributed to the existence of the gaps between the infilled steel plate and the covering concrete slabs. The hysteretic characteristics and the strength and deformation characteristics of this novel BRSPSW have been simulated by using the finite element model, and the test results are in good agreement with the finite element results. Hence, the BRSPSW is an excellent steel plate shear wall to be used in high rise structure to resist horizontal loadings.

scholarly journals Experimental Research and Finite Element Analysis on Mechanical Property of SFRC T-Beam

2017 ◽  
Vol 2017 ◽  
pp. 1-8 ◽  
Author(s):  
Min Sun ◽  
Jiapeng Zhu ◽  
Ning Li ◽  
C. C. Fu
Keyword(s):  
Mechanical Property ◽  
Finite Element ◽  
Shear Capacity ◽  
Steel Fibers ◽  
Test Results ◽  
Element Analysis ◽  
Ansys Simulation ◽  
Finite Element Software ◽  
Ultimate Shear Capacity ◽  
T Beam

Research on mechanical property of SFRC was done through experiments of two SFRC T-beams and one concrete T-beam, while the influences of different volume fractions of steel fibers on integral rigidity, ultimate shear capacity, and the crack distribution characteristics were analyzed. ANSYS finite element software was used to simulate the tests and it was found that there was good conformation between the results of ANSYS simulation and tests. The test results and finite element software simulation both showed that the incorporation of steel fibers in the concrete can increase the integral rigidity and ultimate shear capacity, while partially reducing the propagation of cracks effectively. It was also proved that it is reliable to simulate SFRC T-beam by ANSYS software.

scholarly journals Effect of Corrugation Angle and Direction on the Performance of Corrugated Steel Plate Shear Walls

2018 ◽  
Vol 4 (11) ◽  
pp. 2667
Author(s):  
Hayder Fadhil ◽  
Amer Ibrahim ◽  
Mohammed Mahmood
Keyword(s):  
Steel Plate ◽  
Low Cost ◽  
Shear Walls ◽  
High Strength ◽  
Shear Wall ◽  
Initial Stiffness ◽  
Construction Time ◽  
Element Analysis ◽  
Steel Plate Shear Wall ◽  
Steel Shear Wall

Corrugated steel plate shear wall (CSPSW) is one of the lateral resistance systems which consists mainly of steel frame (beam and column) with vertical or horizontal corrugated steel plate connected to the frame by weld, bolts or both. This type of steel shear wall characterized by low cost and short construction time with high strength, ductility, initial stiffness and excellent ability to dissipate energy. The aim of this paper is to evaluate the effect of corrugation angle and its direction on the performance of CSPSW under cyclic loading. The Finite element analysis was employed to achieve the research aim. The FE models were validated with experimental data available in the literature. Results reveal that the corrugation angle has a clear influence on initial stiffness, strength, ductility, and energy dissipation of CSPSW. The optimum performance of CSPSW can be obtained with angles of 30o for CSPSW with vertical corrugation and 20o for CSPSW with horizontal corrugation. The use of CSPSW with vertical corrugation provides higher strength, stiffness, and ductility compared to CSPSW with horizontal corrugation. Therefore, it is recommended to use CSPSW with vertical corrugation.

An innovative system of coupled steel plate shear wall with pin FUSE in link beam: Cyclic behavior and energy dissipation

2021 ◽  
pp. 136943322110542
Author(s):  
Mahdi Usefvand ◽  
Ahmad Maleki ◽  
Babak Alinejad
Keyword(s):  
Finite Element Method ◽  
Finite Element ◽  
Energy Dissipation ◽  
Steel Plate ◽  
Shear Walls ◽  
Shear Wall ◽  
High Ductility ◽  
The Finite Element Method ◽  
Steel Plate Shear Walls ◽  
Steel Plate Shear Wall

Coupled steel plate shear wall (C-SPSW) is one of the resisting systems with high ductility and energy absorption capacity. Energy dissipation in the C-SPSW system is accomplished by the bending and shear behavior of the link beams and SPSW. Energy dissipation and floor displacement control occur through link beams at low seismic levels, easily replaced after an earthquake. In this study, an innovative coupled steel plate shear wall with a yielding FUSE is presented. The system uses a high-ductility FUSE pin element instead of a link beam, which has good replaceability after the earthquake. In this study, four models of coupled steel plate shear walls were investigated with I-shaped link beam, I-shaped link beam with reduced beam section (RBS), box-link beam with RBS, and FUSE pin element under cyclic loading. The finite element method was used through ABAQUS software to develop the C-SPSW models. Two test specimens of coupled steel plate shear walls were validated to verify the finite element method results. Comparative results of the hysteresis curves obtained from the finite element analysis with the experimental curves indicated that the finite element model offered a good prediction of the hysteresis behavior of C-SPSW. It is demonstrated in this study that the FUSE pin can improve and increase the strength and energy dissipation of a C-SPSW system by 19% and 20%, respectively.

scholarly journals Connection of infill panels in steel plate shear walls

1999 ◽  
Vol 26 (5) ◽  
pp. 549-563 ◽  
Author(s):  
A Schumacher ◽  
G Y Grondin ◽  
G L Kulak
Keyword(s):  
Finite Element ◽  
Cyclic Loading ◽  
Steel Plate ◽  
Shear Walls ◽  
Element Model ◽  
Shear Wall ◽  
Experimental Program ◽  
Steel Plate Shear Wall ◽  
Infill Panels ◽  
Welded Connection

The behaviour under cyclic loading of unstiffened steel plate shear wall panels at their connection to the bounding beams and columns was investigated on full-size panel corner details. Four different infill panel connection details were tested to examine and compare their response to quasi-static cyclic loading. The load versus displacement response of the details showed gradual and stable deterioration at higher loads. The formation of tears in the connection details did not result in a loss of load-carrying capacity. In addition to the experimental program, a finite element model was developed to model the behaviour of one of the infill plate corner connection specimens. Results from the analysis showed that the finite element method can be used to obtain the load versus displacement behaviour of an infill panel-to-boundary member arrangement.Key words: cyclic loading, hysteresis, shear wall, steel, welded connection.

Parametric analysis and calculation method for bending and shear capacities of innovative composite shear walls

2016 ◽  
Vol 20 (7) ◽  
pp. 1046-1058 ◽  
Author(s):  
ZH Chen ◽  
YT Jiang ◽  
XM Zhang ◽  
QY Yang ◽  
WB Li
Keyword(s):  
Finite Element ◽  
Parametric Analysis ◽  
Shear Wall ◽  
Shear Capacity ◽  
Statistical Regression ◽  
Structural Wall ◽  
Shear Span ◽  
Finite Element Software ◽  
Composite Shear Wall ◽  
Composite Shear

The bundled lipped channel-concrete composite wall is an innovative structural wall. This wall has a series of advantages, such as convenient construction and high bearing capacity. Seven full-scaled specimens were tested and subjected to cyclic lateral loads. ABAQUS, which is a finite-element software, was used to simulate the test process. Hysteretic curves and skeleton curves were obtained. This process proved that the simulation effect of finite element was good. A parametric analysis was conducted on this composite shear wall to determine the effect of the wall under different parameters, such as the axial load ratio, the shear span ratio, and the intensity of steel and concrete. The formula for the bending capacity of normal section was deduced. The failure mode and factors that affect the shear capacity of the composite shear wall at a low shear span ratio were analyzed to obtain the composition of the shear capacity. Based on the superposition theory and statistical regression, the formula for the shear capacity of the inclined section was obtained.

ANALYTICAL AND EXPERIMENTAL STUDIES ON 400 kV S/C PORTAL-TYPE GUYED TOWERS

2009 ◽  
Vol 09 (01) ◽  
pp. 85-106
Author(s):  
N. PRASAD RAO ◽  
S. J. MOHAN ◽  
R. P. ROKADE ◽  
R. BALA GOPAL
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Experimental Studies ◽  
Ground Level ◽  
Test Results ◽  
Element Analysis ◽  
Finite Element Software ◽  
The Finite Element Analysis ◽  
Guyed Towers ◽  
Analytical Behavior

The experimental and analytical behavior of 400 kV S/C portal-type guyed towers under different loading conditions is presented. The portal-type tower essentially consists of two masts extending outward in the transverse direction from the beam level to the ground. In addition, two sets of guys connected at the ground level project outward along the longitudinal axes and converge in the transverse axes. The experimental behavior of the guyed tower is compared with the results of finite element analysis. The 400 kV portal-type guyed towers with III and IVI type insulator strings are analyzed using finite element software. Full scale tower test results are verified through comparison with the results of the finite element analysis. The initial prestress in the guys is allowed to vary from 5% to 15% in the finite element modeling. The effect of prestress variation of the guys on the tower behavior is also studied.

Sign in / Sign up

Export Citation Format

Share Document