Bond Integrity of Titanium Surface to Resin Cement After Conditioning with Different Photobiomodulataion Therapy (PBT)

2021 ◽  
Vol 11 (5) ◽  
pp. 970-975
Author(s):  
Khold Al Ahdal ◽  
Laila Al Deeb ◽  
Mohammed S. Bin-Shuwaish ◽  
Rana S. Al-Hamdan ◽  
Modhi Al Deeb ◽  
...  
Keyword(s):  
Titanium Alloy ◽  
Testing Machine ◽  
Resin Cement ◽  
Control Group ◽  
Sem Images ◽  
Group 4 ◽  
Modes Of Failure ◽  
Group 5 ◽  
Group 2 ◽  
Group 1

The aim of the present study was to evaluate the efficacy of interfacial bonding between resin cement and titanium alloy conditioned with different Photobiomodulataion Therapy (PBT) in comparison with conventional regimes. Seventy-five samples of titanium bar were segmented polished; and based on conditioning regime divided into five groups (15 each specimens). Group 1: No treatment (control), Group 2: Sand blasting with 120 µm Al2O3, Group 3: Er,Cr:YSGG (ECL), Group 4: Er:YAG laser (EYL), Group 5: Nd:YAG laser (NYL). After different conditioning regimes, resin cement was mixed and applied. All specimens were thermocycled for 500 cycles and positioned on universal testing machine for shear bond strength testing. Modes of failure was assessed by a single examiner using stereomicroscope at 40× magnification. Three pairs of specimens in each group were sputter coated and scanning electron microscope (SEM) images were taken at 1000× magnification using 20 Kv. The highest SBS values were observed in group 2 (14.25±2.29 MPa) and the lowest bond values were displayed in group 1 (6.98 ±0.59 MPa). Titanium alloy abutments conditioned with different laser prototypes ECL (11.22±1.40 MPa), EYL (9.29±1.22 MPa) and NYL (9.12 ±1.84 MPa) exhibited comparable SBS (p > 0.05). Adhesive failures were primarily dominant among all experimental groups. Photo-biomodulation in the form of ECL lasers has the potential to be used as a supplement to sandblasting procedure in conditioning of cement retained titanium alloy implant abutments.

scholarly journals Shear bond strength of brackets to demineralize enamel after different pretreatment methods

2011 ◽  
Vol 82 (1) ◽  
pp. 56-61 ◽  
Author(s):  
Rengin Attin ◽  
Bogna Stawarczyk ◽  
Defne Keçik ◽  
Michael Knösel ◽  
Dirk Wiechmann ◽  
...  
Keyword(s):  
Bond Strength ◽  
Shear Bond Strength ◽  
Testing Machine ◽  
Resin Cement ◽  
The Other ◽  
Control Group ◽  
Demineralized Enamel ◽  
Group 5 ◽  
Group 2 ◽  
Group 1

Abstract Objective: To compare the influence of demineralized and variously pretreated demineralized enamel on the shear bond strength of orthodontic brackets. Materials and Methods: Sixty bovine enamel specimens were allocated to five groups (n  =  12). Specimens of group 1 were not demineralized and were not pretreated, but served as controls. The other specimens were demineralized to form artificial carious lesions. Samples from group 2 were only demineralized and were kept untreated in artificial saliva. The other samples were pretreated with highly concentrated fluoride preparations (group 3: Elmex Gelee, 1.23% F; group 4: Clinpro White Varnish, 2.23% F) or with an infiltrating resin (group 5: Icon). After respective pretreatments, brackets were adhesively fixed on all specimens with an adhesive system after etching with 35% phosphoric acid and application of a primer and bracket resin cement (Transbond XT). Bracket shear bond strength was evaluated with a universal testing machine. Statistical analysis was performed by one-way analysis of variance followed by a post-hoc Scheffé test. Results: Shear bond strength in control group 1 was statistically significantly greater compared with that in all other groups. Application of the infiltrating resin Icon (group 5) as pretreatment resulted in statistically significantly greater bond strength as compared with pretreatments with fluoride compounds (groups 3 and 4) and treatment provided without pretreatment (group 2). Groups 2, 3, and 4 did not significantly differ from each other. Conclusion: Pretreatment with the infiltrating resin is a beneficial approach to increasing the shear bond strength of brackets to demineralized enamel.

scholarly journals Zingerone Ameliorates Hepatotoxicity

2020 ◽  
Vol 11 (1) ◽  
pp. 280-284 ◽  
Author(s):  
Julietpoornamathy J ◽  
Parameswari C.S.
Keyword(s):  
The Body ◽  
Control Group ◽  
Medical Sciences ◽  
Toxic Compounds ◽  
Group 4 ◽  
Group 3 ◽  
Group 5 ◽  
Group 2 ◽  
Insight Into ◽  
Group 1

In medical sciences, toxicity is an area wherein extensive studies have been carried to improve the diseases as well as to prevent. So, there is a high requirement for novel and improved alternative therapeutic strategies to manage diseases. The liver is the largest gland in the body, which executes several important mechanisms; it stores minerals and vitamins and releases them in periods of need. The main aim of this study was to give a closer insight into potent non- toxic compounds that is capable of modifying the responses. Animals were divided into five equal groups viz control (Group 1), administered with food and water ad libitum, (Group 2) administered with olive oil, (Group 3) administered with zingerone, (Group 4) administered with concanavalin A, (Group 5) administered with cyclosporine A followed by zingerone. Our results revealed significant changes in liver marker enzymes and liver histology of zingerone treated rats when compared to control rats.  A corollary, zingerone has no toxic effect on hepatocytes and was found to be safe at a dose of 10mg/kg b wt and also ameliorates hepatotoxicity.

scholarly journals Effect of Different Neutralizing Agents on Feldspathic Porcelain Etched by Hydrofluoric Acid

2019 ◽  
Vol 13 (01) ◽  
pp. 075-081 ◽  
Author(s):  
Tool Sriamporn ◽  
Ploypim Kraisintu ◽  
Lily Pachanin See ◽  
Somporn Swasdison ◽  
Awiruth Klaisiri ◽  
...  
Keyword(s):  
Bond Strength ◽  
Shear Bond Strength ◽  
Testing Machine ◽  
Control Group ◽  
Sem Images ◽  
Carbonate Group ◽  
Aging Conditions ◽  
Feldspathic Porcelain ◽  
Group 5 ◽  
Group 2

Abstract Objective The aim of this study was to evaluate the effect of neutralizing agents on the shear bond strength of hydrofluoric (HF)–etched porcelain in nonaging and aging conditions. Subjects and Methods One hundred and twenty feldspathic porcelain specimens were prepared and divided into six groups to undergo different surface conditioning methods—group 1: control; group 2: HF; group 3: HF + calcium hydroxide; group 4: HF + calcium carbonate; group 5: HF + calcium gluconate; and group 6: HF + ultrasonic. All samples were immersed in 37°C distilled water for 24 h. Half of the samples were thermocycled in water for 5,000 cycles. The shear bond strength test was performed using a universal testing machine at a crosshead speed of 0.5 mm/min. Data were statistically analyzed by two-way ANOVA and Tukey's multiple comparison test at a 95% confidence level. The surface micromorphology and surface elements were analyzed using scanning electron microscope (SEM) and energy-dispersive X-ray spectroscopy (EDX), respectively. Results The shear bond strengths of groups 2–6 were significantly higher than the control group in both aging and nonaging conditions (p < 0.05). There were no significant differences among all of the HF-etched porcelain groups (p > 0.05). SEM images of groups 2–6 illustrated similar patterns of irregularity on the specimen surfaces. Elemental analysis of EDX demonstrated identical elements on surfaces of specimens of groups 2–6. Conclusion Within the limitations of this study, shear bond strength values between HF-etched porcelain, HF-etching followed by application of neutralizing agents, and HF-etching followed by ultrasonic cleaning were not significantly different in both nonaging and aging conditions.

scholarly journals FE-SEM Evaluation of Dental Specimens Prepared by Different Methods forIn VitroContamination

2012 ◽  
Vol 2012 ◽  
pp. 1-5
Author(s):  
Vitor Cesar Nakamura ◽  
Simony Hidee Hamoy Kataoka ◽  
Giulio Gavini ◽  
Patrícia Helena Ferrari ◽  
Silvana Cai
Keyword(s):  
Control Group ◽  
Buffer Solution ◽  
Morphological Alterations ◽  
Ultrasonic Bath ◽  
Group 4 ◽  
Cement Removal ◽  
Group 3 ◽  
Group 5 ◽  
Group 2 ◽  
Group 1

Objective. To evaluate through FE-SEM the cleanliness and dentinal alterations promoted by different methods of dental sample preparation.Methods. Twenty-five human single-rooted teeth were used. The teeth were cleaned and autoclaved in wet medium and randomly divided into 5 groups (), according to the preparation methods employed—control group: no solutions applied; group 1: cement removal and irrigation with 5.25% % EDTA for 4 minutes each; group 2: 17%  % NaOCl (4 minutes ultrasonic bath); group 3: cement removal and 17%     buffer solution + distilled water (10 minutes ultrasonic); group 4: 17%   NaOCl (3 minutes ultrasonic bath). Specimens were analyzed by field emission scanning electron microscope (FE-SEM), at 1500x magnification. Data were submitted to qualitative analysis according to a scoring system and submitted to Kruskal-Wallis test.Results. In ascending order, as to bind parameters, (i) cleanliness: control, group 2, group 3, group 5, and group 4, (ii) dentinal alterations: group 1, group 5, group 2, group 3, and group 4.Conclusion. The proposed protocol was suitable for subsequent microbiological contamination, because it showed less dentinal morphological alterations with increased removal of organic waste.

scholarly journals The Evaluation of Various Restoration Techniques on Internal Adaptation of Composites in Class V Cavities

2014 ◽  
Vol 2014 ◽  
pp. 1-6 ◽  
Author(s):  
D. Dionysopoulos ◽  
C. Papadopoulos ◽  
E. Koliniotou-Koumpia
Keyword(s):  
Room Temperature ◽  
Control Group ◽  
Class V ◽  
Group 4 ◽  
Restoration Techniques ◽  
Group 3 ◽  
Internal Adaptation ◽  
Group 5 ◽  
Group 2 ◽  
Group 1

Aim.The aim of this study was to evaluate the effect of different restoration techniques on the formation of internal microgaps between materials and dentin in class V restorations.Materials and Methods.Twenty-five extracted human premolars were prepared with standardized class V cavity outlines (3 mm × 2 mm × 2 mm). The cavities were randomly divided into 5 groups of 10 cavities each and restored according to manufacturer’s instructions: Group 1: preheating (55°C) conventional composite (Filtek Z250), Group 2: flowable composite (Filtek Flow), Group 3: Filtek Flow + Filtek Z250 light-cured separately, Group 4: Filtek Flow + Filtek Z250 light-cured simultaneously, and Group 5 (control): Filtek Z250 at room temperature (23°C). The specimens were then thermocycled and cross-sectioned through the center of the restoration. Subsequently, impressions were taken, and epoxy resin replicas were made. The internal adaptation of the materials to the axial wall was analyzed under SEM.Results.The preheated Filtek Z250 (Group 1) showed better internal adaptation than the room temperature groups(P<0.05). The combination of Filtek Flow with Filtek Z250 which was light-cured separately (Group 3) exhibited better internal adaptation than control group(P<0.05).Conclusion.Different restoration techniques exhibit different behavior regarding internal adaptation to dentin after photopolymerization.

scholarly journals Treatment of ovarian cysts in sows – a field trial

2008 ◽  
Vol 52 (No. 9) ◽  
pp. 413-418 ◽  
Author(s):  
S. Cech ◽  
R. Dolezel
Keyword(s):  
The Other ◽  
Ovarian Cysts ◽  
Control Group ◽  
Initial Examination ◽  
Interval Group ◽  
Group 4 ◽  
Group 3 ◽  
Group 5 ◽  
Group 2 ◽  
Group 1

Different procedures of treatment of large follicular ovarian cysts in 177 sows using GnRH, hCG and PGF2α are evaluated in this study. Ovarian cysts were diagnosed by transcutaneous ultrasonography, which was a part of routine pregnancy diagnosis. No treatment was performed in the control group (Group 1, <i>n</i> = 29); the method of treatment used in the other groups immediately after the diagnosis was intramuscular administration of lecirelin in doses 50 µg (Group 2, <i>n</i> = 28), 100 µg (Group 3, <i>n</i> = 27) and 200 µg divided into 2 equal doses administered at a 12-hour interval (Group 4, <i>n<i> = 25) and of hCG in doses 1 500 IU (Group 5, <i>n</i> = 23), 3 000 IU (Group 6, <i>n</i> = 21), and 250 µg of cloprostenol (Group 7, <i>n</i> = 24). Insemination rate (IR), conception rate (CR) in inseminated sows, pregnancy rate (PR = recovery rate), treatment-insemination interval (TII) and treatment-pregnancy interval (TPI) within 42 days after the initial examination were evaluated. In addition PR in groups of sows divided according to parity (1–3, 4–6 and ≥ 7) were also evaluated. IR and PR were higher in Group 4 (84.0% and 44.0%) and lower in Group 1 (17.2% and 6.9%) in comparison with the other groups (<i>P</i> < 0.001 and <i>P</i> < 0.05). CR, TII and TPI did not differ between the experimental groups. PR were similar in sows with different parity. The study proved a positive response in sows with large follicular ovarian cysts to the treatment consisting of 2 administrations of 100 µg GnRH at a 12-hour interval.

scholarly journals Effects of a probiotic in combination with prebiotics on intestinal lactobacilli and coliforms and activities of bacterial enzymes in 1,2-dimethylhydrazine exposed rats

2011 ◽  
Vol 56 (No. 3) ◽  
pp. 99-106 ◽  
Author(s):  
L. Strojný ◽  
A. Bo ◽  
E. Hijová ◽  
A. Chmelárová ◽  
G. Mojžišová ◽  
...  
Keyword(s):  
High Fat Diet ◽  
Control Group ◽  
Group 4 ◽  
Group 3 ◽  
Group 5 ◽  
Group 2 ◽  
Beta Glucosidase ◽  
Alpha Glucosidase ◽  
Beta Galactosidase ◽  
Group 1

Effects of the probiotic (PRO) Lactobacillus plantarum and of the combination of PRO and the prebiotic (PRE) inulin enriched with oligofructose (2%), and PRO with Lini oleum virginale (O) on counts of lactobacilli and coliforms and enzymatic activities in faeces of rats were studied. The rats (n = 60) were divided into 5 groups of 12 subjects. The animals were fed on a high fat diet (10%) for 8 weeks of experiment. Colon cancer was induced by the application of 1,2-dimethylhydrazine (DMH) twice a week in a dose of 20 mg/kg s.c. in groups G2-G5. The rats in group 1 (control 1) received a diet without any supplements. The rats in group 2 (control 2) received 1,2 DMH without any supplements. The rats in group 3 received PRO, group 4 PRO and PRE, and group 5 received PRO and O. A significant decrease (P &lt; 0.05) of coliforms was found out after the application of PRO, PRO-O, and PRO-PRE in comparison with control group G2. Significantly higher (P &lt; 0.05) counts of lactobacilli were determined after the application of PRO-O and PRO-PRE. Significantly lower (P &lt; 0.001) activities of &beta;-galactosidase, &beta;-glucuronidase and &alpha;-glucosidase were observed in PRO, PRO-PRE and PRO-O, while in the case of the enzyme &beta;-glucosidase the activity was lower only after the addition of PRO-O. The protective effect of lactobacilli was observed in the order PRO-O, PRO-PRE, and PRO. It was shown that combinations of PRO-O and PRO-PRE had a synergistic effect which was higher than the effect of administering only PRO.

scholarly journals Effect of the number of thermocycles on microleakage of resin composite restorations

2003 ◽  
Vol 17 (4) ◽  
pp. 337-341 ◽  
Author(s):  
Flávia Bittencourt Pazinatto ◽  
Bruno Barbosa Campos ◽  
Leonardo César Costa ◽  
Maria Teresa Atta
Keyword(s):  
Resin Composite ◽  
Control Group ◽  
Group 4 ◽  
Thermal Changes ◽  
Group 3 ◽  
Group 5 ◽  
Group 2 ◽  
Number Of Cycles ◽  
Group 1

Thermocycling simulates, in vitro, thermal changes that occur in the oral cavity. The aim of this study was to evaluate the influence of the number of cycles on microleakage. Class V cavities (1.5 mm deep, 3 mm in height and 3 mm in width) were prepared in bovine teeth, restored with a Single Bond/Z250 restorative system (3M/ESPE) and then divided into five groups of ten teeth each: group 1 was not thermocycled (control group), and groups 2, 3, 4 and 5 were thermocycled 500, 1,000, 2,500 and 5,000 times, respectively (5º-55º ± 2ºC, 15 s dwell time). The teeth were immersed in 0.5% basic fuchsin aqueous solution for 24 h, sectioned and the sections with the highest degree of microleakage were selected, scanned and the extent of dye penetration was measured by the ImageTool program. The results submitted to one-way ANOVA showed no significant differences between the groups (p > 0.05). The averages of microleakage values in millimeters were: group 1 (3.92); group 2 (3.13); group 3 (4.48); group 4 (4.33) and group 5 (3.42). Thus, it was concluded that there is no relation between the increase of the number of cycles and the increase in microleakage.

scholarly journals Histological and Weight Changes in the Testes of Plasmodium Berghei- Infected Swiss Mice Treated with Chloroquine

2021 ◽  
Vol 4 (2) ◽  
pp. 39-43
Author(s):  
N.S. Etukudoh ◽  
A.B. Deko ◽  
Uchejeso Obeta ◽  
S.K. Oyero ◽  
O.R. Ejinaka ◽  
...  
Keyword(s):  
Plasmodium Berghei ◽  
Seminiferous Tubules ◽  
Control Group ◽  
Weight Changes ◽  
Swiss Mice ◽  
Group 4 ◽  
Group 3 ◽  
Group 5 ◽  
Group 2 ◽  
Group 1

Chloroquine has gained great emphasis in the treatment of malaria. This study sought experimentally to determine the histomorphological and weight changes in the testes of male mice infected with Plasmodium berghei and treated with chloroquine. The study used 30 Swiss mice divided into five groups. Group 1 is Control that was not infected with Plasmodium berghei and not treated with chloroquine as control, Group 2 is Plasmodium (Plasmodiul berghei) Infected animals but not treated, Group 3 is Plasmodium Infected animals + Chloroquine (5mg/kg), Group 4 is Plasmodium Infected animals + Chloroquine (10mg/kg) and Group 5 is Plasmodium Infected animals + Chloroquine (15mg/kg). The mice were treated for 7 days after parasitaemia was confirmed and the Group 2-5 testes studied with reference to Group 1. The results showed that the Group 2 showed a little distortion, difference in spermatogenic activities and increased cellular activities; Group 3 showed large, convoluted tubules, moderate number of spermatids and large interstitial spaces, Group 4 showed Large seminiferous tubules, large spermatids, increased distortion and group 5 showed shrinking of seminiferous tubules, degeneration of interstitial cells of Leydig cells and Sertolic cells with spermatids. Groups 1-5 showed no significant effect in in body weights and testes weights of Swiss mice. Plasmodium berghei (malaria) and chloroquine have effects on histomorphological structures of Swiss mice testes but not on their teste’s weights. The testicular section from Swiss mice infected with malaria and treated at various doses when compared with the Control (Group 1) showed some moderate distortion in some structures like seminiferous tubules, connective tissues between the tubules, lumen and interstitial spaces. It can be deducted that Plasmodium berghei which caused parasitaemia in mice could cause a little tissue effect on mice if not treated.

Effect of simultaneous blockade of androgen and estrogen receptors on prostate cancer: In vivo study.

2013 ◽  
Vol 31 (6_suppl) ◽  
pp. 214-214
Author(s):  
Rafael Nunez-Nateras ◽  
Erin N. Ferrigni ◽  
Naomi M. Gades ◽  
Erik P. Castle
Keyword(s):  
Growth Inhibition ◽  
Control Group ◽  
Group 4 ◽  
Combined Administration ◽  
Group 3 ◽  
Group 5 ◽  
Group 2 ◽  
Castrate Resistant ◽  
Group 1

214 Background: In our preliminary in vitro studies, we have demonstrated evidence of enhanced apoptosis and inhibition of cellular proliferation in both hormone sensitive and castrate resistant prostate cancer (PCa) cell lines using a combination of an antiandrogen (Bicalutamide) and a selective estrogen receptor modulator (Raloxifene). The aim of this study was to study the effect of the administration of these two drugs in in vivo models of castrate resistant PCa. Methods: In vivo model consisted on NCr Nude: Mice bearing s.c. human prostate (PC3 cell line) xenografts. Based on the treatment received, mice were divided into 5 groups as follows: Group 1: No drugs (control); Group 2: Bicalutamide 50mg; Group 3: Raloxifene 60 mg; Group 4: Combined administration of Bicalutamide 50 mg and Raloxifene 60 mg; Group 5 Combined administration of Bicalutamide 150 mg and Raloxifene 120 mg. A total of 10 mice where included in each group. All drugs dosages were converted to their equivalent in the mice. Drugs were administered by gavage technique to the mice once per day for a total of 14 days. Results: As expected, Bicalutamide administered alone causes minimal inhibition without reaching statistical significance (Group 2: 0.34 g Vs Group 1: 0.40 g; p=0.073). Although Raloxifene causes some marked growth inhibition, its effect is not statistically significant (Group 3: 0.31 Vs Group 1: 0.40 g; p=0.062). Bicalutamide and Raloxifene, when administered in combination, induced prominent growth inhibition in PC3 tumors when compared to the control group (Group 4: 0.26 g Vs Group 1: 0.40 g; p=0.038). Growth inhibition is significantly more evident when the drugs dosages are increased (Group 5: 0.17 g Vs Group 1: 0.40 g; p=0.024). Conclusions: The simultaneous administration of Bicalutamide and Raloxifene appears to have a synergistic effect on tumor growth inhibition in PC3 xenografts. The pathway(s) responsible for this observation may be independent of the androgen receptor as PC3 cells are AR negative and still affected by the combination over the drugs administered alone. Research is warranted to identify these potential pathways.

Sign in / Sign up

Export Citation Format

Share Document