Nanoscale Phase Separation in Ternary Organic Solar Cells Based on PTB7:PC70BM:IC70BA

2021 ◽  
Vol 21 (11) ◽  
pp. 5749-5755
Author(s):  
Chang Li ◽  
Wei Li ◽  
Xiaoxiang Sun ◽  
Jifei Wang ◽  
Jiayou Tao ◽  
...  
Keyword(s):  
Solar Cells ◽  
Phase Separation ◽  
Active Layer ◽  
Organic Solar Cells ◽  
Short Circuit ◽  
Weight Ratio ◽  
Short Circuit Current ◽  
Open Circuit ◽  
Hole Transport ◽  
Fullerene Derivative

As a fullerene derivative, IC70BA is widely used in the ternary organic solar cells (TOSCs) to increase the open circuit voltage (Voc) of the devices. Unfortunately, most of the literature shows that IC70BA will lead to a reduction in the short-circuit current density (Jsc) and fill factor (FF). In this work, IC70BA is added to the PTB7:PC70BM binary system to form the ternary system, which is composed of one donor and two fullerene acceptors. Surprisingly, the addition of IC70BA does not immediately lead to a decrease in Jsc and FF. In fact, the appropriate weight ratio of IC70BA in fullerenes can simultaneously increase the Voc, Jsc, and FF of the TOSCs. The synergistic optimization of the surface and bulk morphology of the ternary active layer suppresses the attenuation of Jsc and FF. The smooth surface and suitable phase separation size effectively guarantee the separation, transport and extraction of the charge. Moreover, the addition of IC70BA can significantly improve the hole transport capacity of the active layer, and the optimal hole mobility is 5.13 – 10”4 cm2V–1S–1. Finally, the TOSCs with 10% weight ratio of IC70BA gives the optimal PCE of 9.24% and ideality factor of 2.3.

scholarly journals PREPARATION AND CHARACTERIZATION OF P3HT-PCBM ORGANIC SOLAR CELLS

2013 ◽  
pp. 23-25
Author(s):  
ANUBHAV GUPTA ◽  
PRAVEEN S ◽  
ABHISHEK KUMAR ◽  
PRIYANKA SHREE ◽  
SUCHANA MISHRA
Keyword(s):  
Solar Cells ◽  
Solar Cell ◽  
Active Layer ◽  
Organic Solar Cells ◽  
Silicon Solar Cell ◽  
Short Circuit ◽  
Short Circuit Current ◽  
Open Circuit ◽  
Glass Substrates

Organic solar cells using P3HT: PCBM as an active layer on ITO coated glass substrates were fabricated and characterized. Different air annealing procedures and cathode materials were tried and the characteristics were compared with that of a standard thin film polycrystalline silicon solar cell. It was found that the sample prepared with post-deposition air annealing at 130 oC improves the open circuit voltage (Voc) considerably. Besides, short circuit current (Isc) and the efficiency (η) were highest for the sample with a non annealed active layer. Series resistance (Rs) for this sample was lowest, but 103 times higher than that of the silicon solar cell, which in turn may have reduced the efficiency value for the organic cell compared to silicon.

Study of Al/Organic/ITO Polymer Solar Cell on Glass Substrate

2013 ◽  
Vol 448-453 ◽  
pp. 1446-1451
Author(s):  
Yi Tsung Chang ◽  
Jen Hong Su ◽  
Yi Ting Shih ◽  
Yen Lin Shih
Keyword(s):  
Solar Cells ◽  
Solar Cell ◽  
Active Layer ◽  
Organic Solar Cells ◽  
Glass Substrate ◽  
Polymer Solar Cells ◽  
Short Circuit ◽  
Single Layer ◽  
Short Circuit Current ◽  
Open Circuit

A single layer of organic solar cells with the Al/P3HT/PEDOT: PSS/ITO structure on glass substrate was investigated in this paper, and examined the performance of the polymer solar cells by changing 60, 70 and 80 nm thickness of the P3HT active layer. These devices had better absorption in the active layer and poor charges collect in the electrode with increase thickness of active layer were observed. It is found that the best properties that the single layer organic solar cell with open-circuit voltage 0.457 V, short-circuit current 1.05E-4 mA and power conversion efficiency of 3.3E-5% was achieved under illumination 100 mW/cm2 when the thickness of P3HT active layer is about 80 nm.

scholarly journals Role of Vanadium Pentoxide Hole-Extracting Nanolayer in Rubrene/C70-Based Small Molecule Organic Solar Cells

2014 ◽  
Vol 2014 ◽  
pp. 1-7 ◽  
Author(s):  
Zhen Zhan ◽  
Jing Cao ◽  
Weiguang Xie ◽  
Lintao Hou ◽  
Qin Ye ◽  
...  
Keyword(s):  
Solar Cells ◽  
Vanadium Pentoxide ◽  
Organic Solar Cells ◽  
Fill Factor ◽  
Short Circuit ◽  
Short Circuit Current ◽  
Short Circuit Current Density ◽  
Open Circuit ◽  
Hole Transport ◽  
Heterojunction Solar Cells

Vanadium pentoxideV2O5was inserted between the donor layer and the anode as a hole-extracting nanolayer. Compared with devices without a hole-extracting layer, short-circuit current density (JSC), open-circuit voltage (VOC), fill factor (FF), and power conversion efficiency (PCE) of rubrene/C70-based heterojunction solar cells with 3 nm V2O5nanolayer are enhanced by 99%, 73%, 20%, and 310%, respectively. We found that V2O5interlayer can effectively suppress the contact resistance and increase the hole transport capability. The dependence of the device performance on V2O5layer thickness as well as fill factor on exciton dissociation and charge transport was also investigated in detail.

scholarly journals SCAPS Simulation on P3HT:Graphene Nanocomposites Based Bulk-Heterojunction Organic Solar Cells

2019 ◽  
Vol 9 (1) ◽  
pp. 28
Author(s):  
Nur Shakina Mohd Shariff ◽  
Puteri Sarah Mohamad Saad ◽  
Mohamad Rusop Mahmood
Keyword(s):  
Solar Cells ◽  
Organic Solar Cells ◽  
Fill Factor ◽  
Bulk Heterojunction ◽  
Short Circuit ◽  
Short Circuit Current ◽  
Short Circuit Current Density ◽  
Open Circuit ◽  
Simulation Software ◽  
Capacitance Voltage

There has been an increasing interest towards organic solar cells after the discovery of conjugated polymer and bulk-heterojunction concept. Eventhough organic solar cells are less expensive than inorganic solar cells but the power conversion energy is still considered low. The main objective of this research is to investigate the effect of the P3HT’s thickness and concentration towards the efficiency of the P3HT:Graphene solar cells. A simulation software that is specialize for photovoltaic called SCAPS is used in this research to simulate the effect on the solar cells. The solar cell’s structure will be drawn inside the simulation and the parameters for each layers is inserted. The result such as the open circuit voltage (Voc), short circuit current density (Jsc), fill factor (FF), efficiency (η), capacitance-voltage (C-V) and capacitance-frequency (C-f) characteristic will be calculated by the software and all the results will be put into one graph.

Optical Simulation and Investigation of the Effect of Hysteresis on the Perovskite Solar Cells

NANO ◽  
2019 ◽  
Vol 14 (10) ◽  
pp. 1950127 ◽  
Author(s):  
Farhad Jahantigh ◽  
S. M. Bagher Ghorashi
Keyword(s):  
Grain Size ◽  
Solar Cells ◽  
Open Circuit Voltage ◽  
Short Circuit ◽  
Perovskite Solar Cells ◽  
Short Circuit Current ◽  
Open Circuit ◽  
Hole Transport ◽  
Transport Layer ◽  
Hole Transport Layer

Perovskite solar cells have recently been considered to be an auspicious candidate for the advancement of future photovoltaic research. A power conversion efficiency (PCE) as high as 22% has been reported to be reached, which can be obtained through an inexpensive and high-throughput solution process. Modeling and simulation of these cells can provide deep insights into their fundamental mechanism of performance. In this paper, two different perovskite solar cells are designed by using COMSOL Multiphysics to optimize the thickness of each layer and the overall thickness of the cell. Electric potential, electron and hole concentrations, generation rate, open-circuit voltage, short-circuit current and the output power were calculated. Finally, PCEs of 20.7% and 26.1% were predicted. Afterwards, according to the simulation results, the role of the hole transport layer (HTL) was investigated and the optimum thickness of the perovskite was measured to be 200[Formula: see text]nm for both cells. Therefore, the spin coating settings are selected so that a coating with this thickness for cell 1 is deposited. In order to compare the performance of HTM layer, solar cells with a Spiro-OMeTAD HTM and without the HTM layer in their structure were fabricated. According to the obtained photovoltaic properties, the solar cell made with Spiro-OMeTAD has a more favorable open-circuit voltage ([Formula: see text]), short-circuit current density ([Formula: see text]), fill factor (FF) and PCE compared to the cell without the HTM layer. Also, hysteresis depends strongly on the perovskite grain size, because large average grain size will lead to an increase in the grain’s contact surface area and a decrease in the density of grain boundaries. Finally, according to the results, it was concluded that, in the presence of a hole transport layer, ion transfer was better and ion accumulation was less intense, and therefore, the hysteresis decreases.

Study on the Small Molecule Organic Solar Cells with Anode Buffer Layer

2012 ◽  
Vol 550-553 ◽  
pp. 476-479
Author(s):  
Ai Fen Wang
Keyword(s):  
Buffer Layer ◽  
Active Layer ◽  
Organic Solar Cells ◽  
Short Circuit ◽  
Short Circuit Current ◽  
Photovoltaic Cell ◽  
Open Circuit ◽  
Experimental Result ◽  
Anode Buffer Layer ◽  
Buffer Material

The three photovoltaic cells with two different anode buffer layer on the basis of Pentacene/C60 as active layer was fabicated, the effect and mechanism of anode buffer layer on performance of organic photovoltaic cell are explored. The experimental result shows transition metal oxide inserted between organic active layer and ITO could increase short circuit current and open-circuit voltage,power conversion efficiency is increased to 107%,so it is effective anode buffer material.

scholarly journals Benzothiadiazole Based Cascade Material to Boost the Performance of Inverted Ternary Organic Solar Cells

Energies ◽  
2020 ◽  
Vol 13 (2) ◽  
pp. 450 ◽  
Author(s):  
Miron Krassas ◽  
Christos Polyzoidis ◽  
Pavlos Tzourmpakis ◽  
Dimitriοs M. Kosmidis ◽  
George Viskadouros ◽  
...  
Keyword(s):  
Solar Cells ◽  
Organic Solar Cells ◽  
Short Circuit ◽  
Photovoltaic Performance ◽  
Short Circuit Current ◽  
Short Circuit Current Density ◽  
Open Circuit ◽  
Fused Ring ◽  
Electron Cascade ◽  
First Time

A conjugated, ladder-type multi-fused ring 4,7-dithienbenzothiadiazole:thiophene derivative, named as compound ‘T’, was for the first time incorporated, within the PTB7:PC71BM photoactive layer for inverted ternary organic solar cells (TOSCs) realization. The effective energy level offset caused by compound T between the polymeric donor and fullerene acceptor materials, as well as its resulting potential as electron cascade material contribute to an enhanced exciton dissociation, electron transfer facilitator and thus improved overall photovoltaic performance. The engineering optimization of the inverted TOSC, ITO/PFN/PTB7:Compound T(5% v/v):PC71BM/MoO3/Al, resulted in an overall power conversion efficiency (PCE) of 8.34%, with a short-circuit current density (Jsc) of 16.75 mA cm−2, open-circuit voltage (Voc) of 0.74 V and a fill factor (FF) of 68.1%, under AM1.5G illumination. This photovoltaic performance was improved by approximately 12% with respect to the control binary device.

RELIABILITY STUDIES OF P3HT: PCBM ORGANIC SOLAR CELLS FABRICATED WITH CALCIUM–ALUMINUM AND LITHIUM FLUORIDE–ALUMINIUM CATHODES

2011 ◽  
Vol 10 (04n05) ◽  
pp. 803-807
Author(s):  
T. S. KRISHNAN ◽  
S. SUNDAR KUMAR IYER
Keyword(s):  
Solar Cells ◽  
Organic Solar Cells ◽  
Short Circuit ◽  
Short Circuit Current ◽  
Short Circuit Current Density ◽  
Open Circuit ◽  
Continuous Illumination ◽  
Stress Tests ◽  
Ambient Conditions ◽  
Over Time

This work addresses the shelf life characteristics of P3HT: PCBM blend based organic solar cells (OSC) fabricated with Ca–Al and LiF–Al cathodes. Some of these devices are encapsulated in nitrogen ambient and some in room ambient. Device electrical characteristics are studied under both dark and light. In the analysis under dark ambient conditions, the degradation in peak dark current is monitored over time (in days) and an empirical model is postulated for the degradation based on statistical curve fitting techniques. In the analysis under light, degradation of parameters such as fill factor (FF), open circuit voltage (V oc ) and short circuit current density (J sc ) is monitored over time in these devices (for different cathodes and different ambients) and the results are analyzed and compared. Also, accelerated stress tests are conducted wherein the devices are subjected to continuous illumination for a period of 1.5 h under two different intensities (0.76 sun and 1 sun) and again, the results are analyzed and compared. A model is fitted to the observed degradation in normalized J sc and the degradation constants (k deg ) are obtained. It is seen that the devices fabricated with cathode as LiF–Al and being encapsulated in nitrogen ambient provide the best performance over time.

HYBRID ORGANIC SOLAR CELLS BLENDED WITH CNTs

2015 ◽  
Vol 22 (06) ◽  
pp. 1550072
Author(s):  
SUDIP ADHIKARI ◽  
HIDEO UCHIDA ◽  
MASAYOSHI UMENO
Keyword(s):  
Solar Cells ◽  
Organic Solar Cells ◽  
Short Circuit ◽  
Photovoltaic Performance ◽  
Short Circuit Current ◽  
Short Circuit Current Density ◽  
Open Circuit ◽  
Photovoltaic Device ◽  
Device Fabrication ◽  
Walled Cnts

In this paper, composite carbon nanotubes (C-CNTs); single-walled CNTs (SWCNTs) and multi-walled CNTs (MWCNTs) are synthesized using an ultrasonic nebulizer in a large quartz tube for photovoltaic device fabrication in poly-3-octyl-thiophene (P3OT)/ n - Si heterojunction solar cells. We found that the device fabricated with C-CNTs shows much better photovoltaic performance than that of a device without C-CNTs. The device with C-CNTs shows open-circuit voltage (Voc) of 0.454 V, a short circuit current density (Jsc) of 12.792 mA/cm2, fill factor (FF) of 0.361 and power conversion efficiency of 2.098 %. Here, we proposed that SWCNTs and MWCNTs provide efficient percolation paths for both electron and hole transportation to opposite electrodes and leading to the suppression of charge carrier recombination, thereby increasing the photovoltaic device performance.

scholarly journals Fabrication of Hybrid Polymer Solar Cells By Inverted Structure Based on P3HT:PCBM Active Layer

2017 ◽  
Vol 17 (1) ◽  
pp. 13
Author(s):  
Shobih Shobih ◽  
Rizky Abdillah ◽  
Erlyta Septa Rosa
Keyword(s):  
Solar Cells ◽  
Active Layer ◽  
Bulk Heterojunction ◽  
Polymer Solar Cells ◽  
Short Circuit ◽  
Sol Gel ◽  
Short Circuit Current ◽  
Short Circuit Current Density ◽  
Open Circuit ◽  
Hybrid Polymer

Hybrid polymer solar cell has privilege than its conventional structure, where it usually has structure of (ITO/PEDOT:PSS/Active Layer/Al). In humid environment the PEDOT:PSS will absorb water and hence can easily etch the ITO. Therefore it is necessary to use an alternative method to avoid this drawback and obtain more stable polymer solar cells, namely by using hybrid polymer solar cells structure with an inverted device architecture from the conventional, by reversing the nature of charge collection. In this paper we report the results of the fabrication of inverted bulk heterojunction polymer solar cells based on P3HT:PCBM as active layer, utilizing ZnO interlayer as buffer layer between the ITO and active layer with a stacked structure of ITO/ZnO/P3HT:PCBM/PEDOT:PSS/Ag. The ZnO interlayer is formed through short route, i.e. by dissolving ZnO nanoparticles powder in chloroform-methanol solvent blend rather than by sol-gel process. Based on the measurement results on electrical characteristics of inverted polymer solar cells under 500 W/m2 illumination and AM 1.5 direct filter at room temperature, cell with annealing process of active layer at 110 °C for 10 minutes results in higher cell performance than without annealing, with an open-circuit voltage of 0.21 volt, a short-circuit current density of 1.33 mA/cm2 , a fill factor of 43.1%, and a power conversion efficiency of 0.22%. The low cell’s performance is caused by very rough surface of ZnO interlayer.

Sign in / Sign up

Export Citation Format

Share Document