scholarly journals PREPARATION AND CHARACTERIZATION OF P3HT-PCBM ORGANIC SOLAR CELLS

2013 ◽  
pp. 23-25
Author(s):  
ANUBHAV GUPTA ◽  
PRAVEEN S ◽  
ABHISHEK KUMAR ◽  
PRIYANKA SHREE ◽  
SUCHANA MISHRA
Keyword(s):  
Solar Cells ◽  
Solar Cell ◽  
Active Layer ◽  
Organic Solar Cells ◽  
Silicon Solar Cell ◽  
Short Circuit ◽  
Short Circuit Current ◽  
Open Circuit ◽  
Glass Substrates

Organic solar cells using P3HT: PCBM as an active layer on ITO coated glass substrates were fabricated and characterized. Different air annealing procedures and cathode materials were tried and the characteristics were compared with that of a standard thin film polycrystalline silicon solar cell. It was found that the sample prepared with post-deposition air annealing at 130 oC improves the open circuit voltage (Voc) considerably. Besides, short circuit current (Isc) and the efficiency (η) were highest for the sample with a non annealed active layer. Series resistance (Rs) for this sample was lowest, but 103 times higher than that of the silicon solar cell, which in turn may have reduced the efficiency value for the organic cell compared to silicon.

Study of Al/Organic/ITO Polymer Solar Cell on Glass Substrate

2013 ◽  
Vol 448-453 ◽  
pp. 1446-1451
Author(s):  
Yi Tsung Chang ◽  
Jen Hong Su ◽  
Yi Ting Shih ◽  
Yen Lin Shih
Keyword(s):  
Solar Cells ◽  
Solar Cell ◽  
Active Layer ◽  
Organic Solar Cells ◽  
Glass Substrate ◽  
Polymer Solar Cells ◽  
Short Circuit ◽  
Single Layer ◽  
Short Circuit Current ◽  
Open Circuit

A single layer of organic solar cells with the Al/P3HT/PEDOT: PSS/ITO structure on glass substrate was investigated in this paper, and examined the performance of the polymer solar cells by changing 60, 70 and 80 nm thickness of the P3HT active layer. These devices had better absorption in the active layer and poor charges collect in the electrode with increase thickness of active layer were observed. It is found that the best properties that the single layer organic solar cell with open-circuit voltage 0.457 V, short-circuit current 1.05E-4 mA and power conversion efficiency of 3.3E-5% was achieved under illumination 100 mW/cm2 when the thickness of P3HT active layer is about 80 nm.

Nanoscale Phase Separation in Ternary Organic Solar Cells Based on PTB7:PC70BM:IC70BA

2021 ◽  
Vol 21 (11) ◽  
pp. 5749-5755
Author(s):  
Chang Li ◽  
Wei Li ◽  
Xiaoxiang Sun ◽  
Jifei Wang ◽  
Jiayou Tao ◽  
...  
Keyword(s):  
Solar Cells ◽  
Phase Separation ◽  
Active Layer ◽  
Organic Solar Cells ◽  
Short Circuit ◽  
Weight Ratio ◽  
Short Circuit Current ◽  
Open Circuit ◽  
Hole Transport ◽  
Fullerene Derivative

As a fullerene derivative, IC70BA is widely used in the ternary organic solar cells (TOSCs) to increase the open circuit voltage (Voc) of the devices. Unfortunately, most of the literature shows that IC70BA will lead to a reduction in the short-circuit current density (Jsc) and fill factor (FF). In this work, IC70BA is added to the PTB7:PC70BM binary system to form the ternary system, which is composed of one donor and two fullerene acceptors. Surprisingly, the addition of IC70BA does not immediately lead to a decrease in Jsc and FF. In fact, the appropriate weight ratio of IC70BA in fullerenes can simultaneously increase the Voc, Jsc, and FF of the TOSCs. The synergistic optimization of the surface and bulk morphology of the ternary active layer suppresses the attenuation of Jsc and FF. The smooth surface and suitable phase separation size effectively guarantee the separation, transport and extraction of the charge. Moreover, the addition of IC70BA can significantly improve the hole transport capacity of the active layer, and the optimal hole mobility is 5.13 – 10”4 cm2V–1S–1. Finally, the TOSCs with 10% weight ratio of IC70BA gives the optimal PCE of 9.24% and ideality factor of 2.3.

scholarly journals CdTe-Based Thin Film Solar Cells: Past, Present and Future

Energies ◽  
2021 ◽  
Vol 14 (6) ◽  
pp. 1684
Author(s):  
Alessandro Romeo ◽  
Elisa Artegiani
Keyword(s):  
Thin Film ◽  
Solar Cells ◽  
Solar Cell ◽  
Short Circuit ◽  
Short Circuit Current ◽  
Short Circuit Current Density ◽  
Open Circuit ◽  
Early Years ◽  
Solar Cell Efficiency ◽  
Cell Efficiency

CdTe is a very robust and chemically stable material and for this reason its related solar cell thin film photovoltaic technology is now the only thin film technology in the first 10 top producers in the world. CdTe has an optimum band gap for the Schockley-Queisser limit and could deliver very high efficiencies as single junction device of more than 32%, with an open circuit voltage of 1 V and a short circuit current density exceeding 30 mA/cm2. CdTe solar cells were introduced at the beginning of the 70s and they have been studied and implemented particularly in the last 30 years. The strong improvement in efficiency in the last 5 years was obtained by a new redesign of the CdTe solar cell device reaching a single solar cell efficiency of 22.1% and a module efficiency of 19%. In this paper we describe the fabrication process following the history of the solar cell as it was developed in the early years up to the latest development and changes. Moreover the paper also presents future possible alternative absorbers and discusses the only apparently controversial environmental impacts of this fantastic technology.

scholarly journals GaInP/GaAs/poly-Si Multi-Junction Solar Cells by in Metal Balls Bonding

Crystals ◽  
2021 ◽  
Vol 11 (7) ◽  
pp. 726
Author(s):  
Ray-Hua Horng ◽  
Yu-Cheng Kao ◽  
Apoorva Sood ◽  
Po-Liang Liu ◽  
Wei-Cheng Wang ◽  
...  
Keyword(s):  
Solar Cells ◽  
Solar Cell ◽  
Low Temperature ◽  
Triple Junction ◽  
Short Circuit ◽  
Short Circuit Current ◽  
Open Circuit ◽  
Metal Line ◽  
Solar Simulator ◽  
Junction Solar Cell

In this study, a mechanical stacking technique has been used to bond together the GaInP/GaAs and poly-silicon (Si) solar wafers. A GaInP/GaAs/poly-Si triple-junction solar cell has mechanically stacked using a low-temperature bonding process which involves micro metal In balls on a metal line using a high-optical-transmission spin-coated glue material. Current–voltage measurements of the GaInP/GaAs/poly-Si triple-junction solar cells have carried out at room temperature both in the dark and under 1 sun with 100 mW/cm2 power density using a solar simulator. The GaInP/GaAs/poly-Si triple-junction solar cell has reached an efficiency of 24.5% with an open-circuit voltage of 2.68 V, a short-circuit current density of 12.39 mA/cm2, and a fill-factor of 73.8%. This study demonstrates a great potential for the low-temperature micro-metal-ball mechanical stacking technique to achieve high conversion efficiency for solar cells with three or more junctions.

An Improved Triple-Tandem Organic Solar Cell

2009 ◽  
Vol 1212 ◽  
Author(s):  
Dewei Zhao ◽  
Xiao Wei Sun ◽  
Lin Ke ◽  
Swee Tiam Tan
Keyword(s):  
Solar Cell ◽  
Small Molecule ◽  
Organic Solar Cells ◽  
Organic Solar Cell ◽  
Copper Phthalocyanine ◽  
Short Circuit ◽  
Short Circuit Current ◽  
Open Circuit ◽  
Solar Irradiation ◽  
The Third

AbstractWe present an efficient polymer-small molecule triple-tandem organic solar cell (OSC), consisting of poly(3-hexylthiophene) (P3HT) and 1-(3-methoxycarbonyl)-propyl-1-phenyl-(6,6)C61 (PCBM) bulk heterojunction as the first and second cells, and small molecules copper phthalocyanine (CuPc) and fullerene (C60) as the third cell on top. These sub-cells are connected by an intermediate layer of Al(1 nm)/MoO3(15 nm), which appears to be highly transparent, structurally smooth, and electrically functional. Compared to our previous all polymer triple-tandem organic solar cells (2.03%), this polymer-small molecule triple-tandem organic solar cell achieves an improved power conversion efficiency of 2.18% with a short-circuit current density (Jsc) = 3.02 mA/cm2, open-circuit voltage (Voc) = 1.51 V, and fill factor (FF) = 47.7% under simulated solar irradiation of 100 mW/cm2 (AM1.5G), which can be attributed to the increased photocurrent generation in the third cell since the third cell has the complementary absorption with two bottom cells despite a slightly reduced Voc.

Study of Photoelectrochemical Solar Cell Using WSe2 Crystal

2013 ◽  
Vol 665 ◽  
pp. 330-335 ◽  
Author(s):  
Ripal Parmar ◽  
Dipak Sahay ◽  
R.J. Pathak ◽  
R.K. Shah
Keyword(s):  
Solar Cells ◽  
Solar Cell ◽  
Fill Factor ◽  
Short Circuit ◽  
Short Circuit Current ◽  
Electrical Energy ◽  
Open Circuit ◽  
Cell Parameters ◽  
Photoelectrochemical Solar Cell ◽  
Photoelectrochemical Solar Cells

The solar cells have been used as most promising device to convert light energy into electrical energy. In this paper authors have attempted to fabricate Photoelectrochemical solar cell with semiconductor electrode using TMDCs. The Photoelectrochemical solar cells are the solar cells which convert the solar energy into electrical energy. The photoelectrochemical cells are clean and inexhaustible sources of energy. The photoelectrochemical solar cells are fabricated using WSe2crystal and electrolyte solution of 0.025M I2, 0.5M NaI, 0.5M Na2SO4. Here the WSe2crystals were grown by direct vapour transport technique. In our investigations the solar cell parameters like short circuit current (Isc) and Open circuit voltage (Voc) were measured and from that Fill factor (F.F.) and photoconversion efficiency (η) are investigated. The results obtained shows that the value of efficiency and fill factor of solar cell varies with the illumination intensities.

scholarly journals SCAPS Simulation on P3HT:Graphene Nanocomposites Based Bulk-Heterojunction Organic Solar Cells

2019 ◽  
Vol 9 (1) ◽  
pp. 28
Author(s):  
Nur Shakina Mohd Shariff ◽  
Puteri Sarah Mohamad Saad ◽  
Mohamad Rusop Mahmood
Keyword(s):  
Solar Cells ◽  
Organic Solar Cells ◽  
Fill Factor ◽  
Bulk Heterojunction ◽  
Short Circuit ◽  
Short Circuit Current ◽  
Short Circuit Current Density ◽  
Open Circuit ◽  
Simulation Software ◽  
Capacitance Voltage

There has been an increasing interest towards organic solar cells after the discovery of conjugated polymer and bulk-heterojunction concept. Eventhough organic solar cells are less expensive than inorganic solar cells but the power conversion energy is still considered low. The main objective of this research is to investigate the effect of the P3HT’s thickness and concentration towards the efficiency of the P3HT:Graphene solar cells. A simulation software that is specialize for photovoltaic called SCAPS is used in this research to simulate the effect on the solar cells. The solar cell’s structure will be drawn inside the simulation and the parameters for each layers is inserted. The result such as the open circuit voltage (Voc), short circuit current density (Jsc), fill factor (FF), efficiency (η), capacitance-voltage (C-V) and capacitance-frequency (C-f) characteristic will be calculated by the software and all the results will be put into one graph.

scholarly journals Analytical Study of the Electrical Output Characteristics of c-Si Solar Cells by Cut and Shading Phenomena

Energies ◽  
2018 ◽  
Vol 11 (12) ◽  
pp. 3397 ◽  
Author(s):  
Jong Lim ◽  
Woo Shin ◽  
Hyemi Hwang ◽  
Young-Chul Ju ◽  
Suk Ko ◽  
...  
Keyword(s):  
Solar Cells ◽  
Solar Cell ◽  
Crystalline Silicon ◽  
Short Circuit ◽  
Incident Light ◽  
Short Circuit Current ◽  
Open Circuit ◽  
Si Solar Cell ◽  
Si Solar Cells ◽  
Electrical Output

Cut solar cells have received considerable attention recently as they can reduce electrical output degradation when the c-Si solar cells (crystalline-silicon solar cells) are shaded. Cut c-Si solar cells have a lower short-circuit current than normal solar cells and the decrease in short-circuit currents is similar to the shading effect of c-Si solar cells. However, the results of this study’s experiment show that the shadow effect of a c-Si solar cell reduces the V o c (open circuit voltage) in the c-Si solar cell but the V o c does not change when the c-Si solar cell is cut because the amount of incident light does not change. In this paper, the limitations of the electrical power analysis of the cut solar cells were identified when only photo current was considered and the analysis of the electric output of the cut c-Si solar cells was interpreted with a method different from that used in previous analyses. Electrical output was measured when the shaded and cut rates of c-Si solar cells were increased from 0% to 25, 50 and 75%, and a new theoretical model was compared with the experimental results using MATLAB.

Study on the Small Molecule Organic Solar Cells with Anode Buffer Layer

2012 ◽  
Vol 550-553 ◽  
pp. 476-479
Author(s):  
Ai Fen Wang
Keyword(s):  
Buffer Layer ◽  
Active Layer ◽  
Organic Solar Cells ◽  
Short Circuit ◽  
Short Circuit Current ◽  
Photovoltaic Cell ◽  
Open Circuit ◽  
Experimental Result ◽  
Anode Buffer Layer ◽  
Buffer Material

The three photovoltaic cells with two different anode buffer layer on the basis of Pentacene/C60 as active layer was fabicated, the effect and mechanism of anode buffer layer on performance of organic photovoltaic cell are explored. The experimental result shows transition metal oxide inserted between organic active layer and ITO could increase short circuit current and open-circuit voltage,power conversion efficiency is increased to 107%,so it is effective anode buffer material.

scholarly journals Benzothiadiazole Based Cascade Material to Boost the Performance of Inverted Ternary Organic Solar Cells

Energies ◽  
2020 ◽  
Vol 13 (2) ◽  
pp. 450 ◽  
Author(s):  
Miron Krassas ◽  
Christos Polyzoidis ◽  
Pavlos Tzourmpakis ◽  
Dimitriοs M. Kosmidis ◽  
George Viskadouros ◽  
...  
Keyword(s):  
Solar Cells ◽  
Organic Solar Cells ◽  
Short Circuit ◽  
Photovoltaic Performance ◽  
Short Circuit Current ◽  
Short Circuit Current Density ◽  
Open Circuit ◽  
Fused Ring ◽  
Electron Cascade ◽  
First Time

A conjugated, ladder-type multi-fused ring 4,7-dithienbenzothiadiazole:thiophene derivative, named as compound ‘T’, was for the first time incorporated, within the PTB7:PC71BM photoactive layer for inverted ternary organic solar cells (TOSCs) realization. The effective energy level offset caused by compound T between the polymeric donor and fullerene acceptor materials, as well as its resulting potential as electron cascade material contribute to an enhanced exciton dissociation, electron transfer facilitator and thus improved overall photovoltaic performance. The engineering optimization of the inverted TOSC, ITO/PFN/PTB7:Compound T(5% v/v):PC71BM/MoO3/Al, resulted in an overall power conversion efficiency (PCE) of 8.34%, with a short-circuit current density (Jsc) of 16.75 mA cm−2, open-circuit voltage (Voc) of 0.74 V and a fill factor (FF) of 68.1%, under AM1.5G illumination. This photovoltaic performance was improved by approximately 12% with respect to the control binary device.

Sign in / Sign up

Export Citation Format

Share Document