scholarly journals Design and Application of an Unattended Multifunctional H-TDMA System

2013 ◽  
Vol 30 (6) ◽  
pp. 1136-1148 ◽  
Author(s):  
Haobo Tan ◽  
Hanbing Xu ◽  
Qilin Wan ◽  
Fei Li ◽  
Xuejiao Deng ◽  
...  
Keyword(s):  
Particle Size ◽  
Growth Factor ◽  
Cloud Condensation Nuclei ◽  
Polystyrene Latex ◽  
Hygroscopic Growth ◽  
Differential Mobility Analyzer ◽  
Differential Mobility ◽  
China Meteorological Administration ◽  
Hygroscopic Properties ◽  
Calibration Methods

Abstract The hygroscopic properties of aerosols have a significant impact on aerosol particle number size distributions (PNSD), formation of cloud condensation nuclei, climate forcing, and atmospheric visibility, as well as human health. To allow for the observation of the hygroscopic growth of aerosols with long-term accuracy, an unattended multifunctional hygroscopicity-tandem differential mobility analyzer (H-TDMA) system was designed and built by the Institute of Tropical and Marine Meteorology (ITMM), China Meteorological Administration (CMA), in Guangzhou, China. The system is capable of measuring dry and wet PNSD, hygroscopic growth factor by particle size, and mixing states. This article describes in detail the working principles, components, and calibration methods of the system. Standard polystyrene latex (PSL) spheres with five different diameters were chosen to test the system’s precision and accuracy of particle size measurement. Ammonium sulfate was used to test the hygroscopic response of the system for accurate growth factor measurement. The test results show that the deviation of the growth factor measured by the system is within a scope of −0.01 to −0.03 compared to Köhler theoretical curves. Results of temperature and humidity control performance tests indicate that the system is robust. An internal temperature gradient of less than 0.2 K for a second differential mobility analyzer (DMA2) makes it possible to reach a set-point relative humidity (RH) value of 90% and with a standard deviation of ±0.44%, sufficient for unattended field observation.

scholarly journals Hygroscopic properties and mixing state of aerosol measured at the high altitude site Puy de Dôme (1465 m a.s.l.), France

2014 ◽  
Vol 14 (5) ◽  
pp. 6759-6802
Author(s):  
H. Holmgren ◽  
K. Sellegri ◽  
M. Hervo ◽  
C. Rose ◽  
E. Freney ◽  
...  
Keyword(s):  
Boundary Layer ◽  
Particle Size ◽  
Growth Factor ◽  
High Altitude ◽  
Hygroscopic Growth ◽  
Mixing State ◽  
Air Mass ◽  
Hygroscopic Properties ◽  
Seasonal And Diurnal Variations ◽  
Mass Type

Abstract. A Hygroscopicity Tandem Differential Mobility Analyzer (HTDMA) was used to evaluate the hygroscopic properties of aerosol particles measured at the Puy de Dôme research station in central France from September 2008 to December 2012. This high-altitude site is ideally situated to allow for both the upper part of the planetary boundary layer and the lower free troposphere to be sampled. The aim of the study is to investigate both the influence of year-to-year, seasonal, and diurnal cycles, as well as the influence of air mass type on particle hygroscopicity and mixing state. Results show that particle hygroscopicity increases with particle size and depends both on air mass type and on season. Average growth factor values are lowest in winter (1.21 ± 0.13, 1.23 ± 0.18 and 1.38 ± 0.25 for 25, 50 and 165 nm particles, respectively) and highest in autumn (1.27 ± 0.11, 1.32 ± 0.12 and 1.49 ± 0.15 for 25, 50 and 165 nm particles, respectively). Particles are generally more hygroscopic at night than during the day. The seasonal and diurnal variations are likely to be strongly influenced by boundary layer dynamics. Furthermore, particles originating from oceanic and continental regions tend to be more hygroscopic than those measured in African and local air masses. The high hygroscopicity of marine aerosol may be explained by large proportions of inorganic aerosol and sea salts, and it is speculated that continental particles are more hygroscopic than local and African ones due to ageing of fresh combustion aerosol. Aerosol measured at the Puy de Dôme display a high degree of external mixing, and hygroscopic growth spectra can be divided into three different hygroscopic modes: a less hygroscopic mode (GF < 1.3), a hygroscopic mode (GF 1.3–1.7) and a more hygroscopic mode (GF > 1.7). The majority of particles measured can be classified as being in either the less hygroscopic mode or the hygroscopic mode, and only few of them have more hygroscopic properties. The degree of external mixing, evaluated as the fraction of time when the aerosol is found with two or more populations with different hygroscopic properties, is found to increase with particle size (average yearly values are 22, 33 and 49% for 25, 50, and 165 nm particles, respectively). The degree of external mixing is more sensitive to season than to air mass type, and it is higher in the cold seasons than in the warm seasons. This study gathers the results from one of the longest data sets of hygroscopic growth factor measurements to date, allowing a statistically relevant hygroscopic growth parameterization to be determined as a function of both air mass type and season.

scholarly journals Hygroscopic properties of the ambient aerosol in southern Sweden – a two year study

2011 ◽  
Vol 11 (2) ◽  
pp. 6601-6650
Author(s):  
E. O. Fors ◽  
E. Swietlicki ◽  
B. Svenningsson ◽  
A. Kristensson ◽  
G. P. Frank ◽  
...  
Keyword(s):  
Seasonal Variation ◽  
Growth Factors ◽  
Radiative Forcing ◽  
Cloud Condensation Nuclei ◽  
Hygroscopic Growth ◽  
Differential Mobility ◽  
Hygroscopic Properties ◽  
Modeling Uncertainties ◽  
Hydrophobic Particles ◽  
Particle Sizer

Abstract. The hygroscopic growth of the atmospheric aerosol is a critical parameter for quantifying the anthropogenic radiative forcing. Until now, there has been a lack of long term measurements due to limitations in instrumental techniques. In this work, for the first time the seasonal variation of the hygroscopic properties of a continental background aerosol has been described, based on more than two years of continuous measurements. In addition to this, the diurnal variation of the hygroscopic growth has been investigated, as well as the seasonal variation in CCN concentration. These physical properties of the aerosol have been measured with a Hygroscopic Tandem Differential Mobility Analyzer (H-TDMA), a Differential Mobility Particle Sizer (DMPS), and a Cloud Condensation Nuclei Counter (CCNC). The results show that smaller particles are generally less hygroscopic than larger ones, and that there is a clear difference in the hygroscopic properties between the Aitken and the accumulation mode. A seasonal cycle was found for all particle sizes. In general, the average hygroscopic growth is lower during wintertime, due to an increase in the relative abundance of less hygroscopic or hydrophobic particles. Monthly averages showed that the hygroscopic growth factors of the two dominating hygroscopic modes (one barely hygroscopic and one more hygroscopic) were relatively stable. The hygroscopic growth additionally showed a diurnal cycle, with higher growth factors during day time. CCN predictions based on H-TDMA data underpredicted the activated CCN concentration with 7% for 1% water supersaturation (s). The underprediction increases with decreasing $s$, most likely due to a combination of measurement and modeling uncertainties. It was found that although the aerosol is often externally mixed, recalculating to an internal mixture with respect to hygroscopicity did not change CCN parameterizations significantly.

scholarly journals Water uptake of subpollen aerosol particles: hygroscopic growth, cloud condensation nuclei activation, and liquid–liquid phase separation

2021 ◽  
Vol 21 (9) ◽  
pp. 6999-7022
Author(s):  
Eugene F. Mikhailov ◽  
Mira L. Pöhlker ◽  
Kathrin Reinmuth-Selzle ◽  
Sergey S. Vlasenko ◽  
Ovid O. Krüger ◽  
...  
Keyword(s):  
Phase Separation ◽  
Liquid Phase ◽  
Water Uptake ◽  
Cloud Condensation Nuclei ◽  
Liquid Phase Separation ◽  
Hygroscopic Growth ◽  
Differential Mobility Analyzer ◽  
Condensation Nuclei ◽  
Differential Mobility ◽  
Liquid Liquid Phase Separation

Abstract. Pollen grains emitted from vegetation can release subpollen particles (SPPs) that contribute to the fine fraction of atmospheric aerosols and may act as cloud condensation nuclei (CCN), ice nuclei (IN), or aeroallergens. Here, we investigate and characterize the hygroscopic growth and CCN activation of birch, pine, and rapeseed SPPs. A high-humidity tandem differential mobility analyzer (HHTDMA) was used to measure particle restructuring and water uptake over a wide range of relative humidity (RH) from 2 % to 99.5 %, and a continuous flow CCN counter was used for size-resolved measurements of CCN activation at supersaturations (S) in the range of 0.2 % to 1.2 %. For both subsaturated and supersaturated conditions, effective hygroscopicity parameters, κ, were obtained by Köhler model calculations. Gravimetric and chemical analyses, electron microscopy, and dynamic light scattering measurements were performed to characterize further properties of SPPs from aqueous pollen extracts such as chemical composition (starch, proteins, DNA, and inorganic ions) and the hydrodynamic size distribution of water-insoluble material. All investigated SPP samples exhibited a sharp increase of water uptake and κ above ∼95 % RH, suggesting a liquid–liquid phase separation (LLPS). The HHTDMA measurements at RH >95 % enable closure between the CCN activation at water vapor supersaturation and hygroscopic growth at subsaturated conditions, which is often not achieved when hygroscopicity tandem differential mobility analyzer (HTDMA) measurements are performed at lower RH where the water uptake and effective hygroscopicity may be limited by the effects of LLPS. Such effects may be important not only for closure between hygroscopic growth and CCN activation but also for the chemical reactivity, allergenic potential, and related health effects of SPPs.

scholarly journals Particle hygroscopicity and its link to chemical composition in the urban atmosphere of Beijing, China, during summertime

2016 ◽  
Vol 16 (2) ◽  
pp. 1123-1138 ◽  
Author(s):  
Z. J. Wu ◽  
J. Zheng ◽  
D. J. Shang ◽  
Z. F. Du ◽  
Y. S. Wu ◽  
...  
Keyword(s):  
Particle Size ◽  
Chemical Composition ◽  
Growth Factor ◽  
Mass Concentration ◽  
Particle Formation ◽  
High Time Resolution ◽  
New Particle Formation ◽  
Hygroscopic Growth ◽  
Hygroscopic Properties ◽  
Beijing China

Abstract. Simultaneous measurements of particle number size distribution, particle hygroscopic properties, and size-resolved chemical composition were made during the summer of 2014 in Beijing, China. During the measurement period, the mean hygroscopicity parameters (κs) of 50, 100, 150, 200, and 250 nm particles were respectively 0.16  &amp;pm;  0.07, 0.19  &amp;pm;  0.06, 0.22  &amp;pm;  0.06, 0.26  &amp;pm;  0.07, and 0.28  &amp;pm;  0.10, showing an increasing trend with increasing particle size. Such size dependency of particle hygroscopicity was similar to that of the inorganic mass fraction in PM1. The hydrophilic mode (hygroscopic growth factor, HGF  >  1.2) was more prominent in growth factor probability density distributions and its dominance of hydrophilic mode became more pronounced with increasing particle size. When PM2.5 mass concentration was greater than 50 μg m−3, the fractions of the hydrophilic mode for 150, 250, and 350 nm particles increased towards 1 as PM2.5 mass concentration increased. This indicates that aged particles dominated during severe pollution periods in the atmosphere of Beijing. Particle hygroscopic growth can be well predicted using high-time-resolution size-resolved chemical composition derived from aerosol mass spectrometer (AMS) measurements using the Zdanovskii–Stokes–Robinson (ZSR) mixing rule. The organic hygroscopicity parameter (κorg) showed a positive correlation with the oxygen to carbon ratio. During the new particle formation event associated with strongly active photochemistry, the hygroscopic growth factor or κ of newly formed particles is greater than for particles with the same sizes not during new particle formation (NPF) periods. A quick transformation from external mixture to internal mixture for pre-existing particles (for example, 250 nm particles) was observed. Such transformations may modify the state of the mixture of pre-existing particles and thus modify properties such as the light absorption coefficient and cloud condensation nuclei activation.

scholarly journals Hygroscopic growth of urban aerosol particles in Beijing (China) during wintertime: a comparison of three experimental methods

2009 ◽  
Vol 9 (18) ◽  
pp. 6865-6880 ◽  
Author(s):  
J. Meier ◽  
B. Wehner ◽  
A. Massling ◽  
W. Birmili ◽  
A. Nowak ◽  
...  
Keyword(s):  
Growth Factors ◽  
Growth Factor ◽  
The Other ◽  
Hygroscopic Growth ◽  
Differential Mobility ◽  
Accumulation Mode ◽  
Hygroscopic Properties ◽  
Solubility Model ◽  
Particle Sizer ◽  
Beijing China

Abstract. The hygroscopic properties of atmospheric aerosols are highly relevant for the quantification of radiative effects in the atmosphere, but also of interest for the assessment of particle health effects upon inhalation. This article reports measurements of aerosol particle hygroscopicity in the highly polluted urban atmosphere of Beijing, China in January 2005. The meteorological conditions corresponded to a relatively cold and dry atmosphere. Three different methods were used: 1) A combination of Humidifying Differential Mobility Particle Sizer (H-DMPS) and Twin Differential Mobility Particle Sizer (TDMPS) measurements, 2) A Hygroscopic Tandem Differential Mobility Analyzer (H-TDMA), and 3) A simplistic solubility model fed by chemical particle composition determined from Micro Orifice Uniform Deposit Impactor (MOUDI) samples. From the H-DMPS and TDMPS particle number size distributions, a size-resolved descriptive hygroscopic growth factor (DHGF) was determined for the relative humidities (RH) 55%, 77% and 90%, and particle diameters between 30 and 400 nm. In Beijing, the highest DHGFs were observed for accumulation mode particles, 1.40 (±0.03) at 90% RH. DHGF decreased significantly with particle size, reaching 1.04 (±0.15) at 30 nm. H-TDMA data also suggest a decrease in growth factor towards the biggest particles investigated (350 nm), associated with an increasing fraction of nearly hydrophobic particles. The agreement between the H-DMPS/TDMPS and H-TDMA methods was satisfactory in the accumulation mode size range (100–400 nm). In the Aitken mode range (<100 nm), the H-DMPS/TDMPS method yielded growth factors lower by up to 0.1 at 90% RH. The application of the solubility model based on measured chemical composition clearly reproduced the size-dependent trend in hygroscopic particle growth observed by the other methods. In the case of aerosol dominated by inorganic ions, the composition-derived growth factors tended to agree (± 0.05) or underestimate (up to 0.1) the values measured by the other two methods. In the case of aerosol dominated by organics, the reverse was true, with an overestimation of up to 0.2. The results shed light on the experimental and methodological uncertainties that are still connected with the determination of hygroscopic growth factors.

scholarly journals Hygroscopic properties of the ambient aerosol in southern Sweden – a two year study

2011 ◽  
Vol 11 (16) ◽  
pp. 8343-8361 ◽  
Author(s):  
E. O. Fors ◽  
E. Swietlicki ◽  
B. Svenningsson ◽  
A. Kristensson ◽  
G. P. Frank ◽  
...  
Keyword(s):  
Seasonal Variation ◽  
Growth Factors ◽  
Radiative Forcing ◽  
Cloud Condensation Nuclei ◽  
Hygroscopic Growth ◽  
Differential Mobility ◽  
Supersaturation Ratio ◽  
Hygroscopic Properties ◽  
Modeling Uncertainties ◽  
Particle Sizer

Abstract. The hygroscopic growth of the atmospheric aerosol is a critical parameter for quantifying the anthropogenic radiative forcing. Until now, there has been a lack of long term measurements due to limitations in instrumental techniques. In this work, for the first time the seasonal variation of the hygroscopic properties of a continental background aerosol has been described, based on more than two years of continuous measurements. In addition to this, the diurnal variation of the hygroscopic growth has been investigated, as well as the seasonal variation in CCN concentration. These physical properties of the aerosol have been measured with a Hygroscopic Tandem Differential Mobility Analyzer (H-TDMA), a Differential Mobility Particle Sizer (DMPS), and a Cloud Condensation Nuclei Counter (CCNC). The results show that smaller particles are generally less hygroscopic than larger ones, and that there is a clear difference in the hygroscopic properties between the Aitken and the accumulation mode. A seasonal cycle was found for all particle sizes. In general, the average hygroscopic growth is lower during wintertime, due to an increase in the relative abundance of less hygroscopic or barely hygroscopic particles. Monthly averages showed that the hygroscopic growth factors of the two dominating hygroscopic modes (one barely hygroscopic and one more hygroscopic) were relatively stable. The hygroscopic growth additionally showed a diurnal cycle, with higher growth factors during day time. CCN predictions based on H-TDMA data underpredicted the activated CCN number concentration with 7 % for a 1 % water supersaturation ratio. The underprediction increases with decreasing s, most likely due to a combination of measurement and modeling uncertainties. It was found that although the aerosol is often externally mixed, recalculating to an internal mixture with respect to hygroscopicity did not change the CCN concentration as a function of supersaturation significantly.

scholarly journals Nano-hygroscopicity tandem differential mobility analyzer (nano-HTDMA) for investigating hygroscopic properties of sub-10 nm aerosol nanoparticles

2020 ◽  
Author(s):  
Ting Lei ◽  
Nan Ma ◽  
Juan Hong ◽  
Thomas Tuch ◽  
Xin Wang ◽  
...  
Keyword(s):  
Materials Science ◽  
Current Knowledge ◽  
Measurement Techniques ◽  
Chemical Properties ◽  
High Accuracy ◽  
Hygroscopic Growth ◽  
Differential Mobility Analyzer ◽  
Differential Mobility ◽  
Aerosol Nanoparticles ◽  
Hygroscopic Properties

Abstract. Interactions between water and nanoparticles are relevant for atmospheric multiphase processes, physical chemistry, and materials science. Current knowledge of the hygroscopic and related physico-chemical properties of nanoparticles, however, is restricted by limitations of the available measurement techniques. Here, we present the design and performance of a nano-hygroscopicity tandem differential mobility analyzer (nano-HTDMA) apparatus that enables high accuracy and precision in hygroscopic growth measurements of aerosol nanoparticles with diameters less than 10 nm. Detailed methods of calibration and validation are provided. Beside maintaining accurate and stable sheath/aerosol flow rates (± 1 %), high accuracy of DMA voltage (± 0.1 %) in the range of ~0–50 V is crucial to achieve accurate sizing and small sizing offsets between the two DMAs (

scholarly journals Hygroscopic properties and mixing state of aerosol measured at the high-altitude site Puy de Dôme (1465 m a.s.l.), France

2014 ◽  
Vol 14 (18) ◽  
pp. 9537-9554 ◽  
Author(s):  
H. Holmgren ◽  
K. Sellegri ◽  
M. Hervo ◽  
C. Rose ◽  
E. Freney ◽  
...  
Keyword(s):  
Boundary Layer ◽  
Particle Size ◽  
Growth Factor ◽  
High Altitude ◽  
Hygroscopic Growth ◽  
Mixing State ◽  
Air Mass ◽  
Hygroscopic Properties ◽  
Seasonal And Diurnal Variations ◽  
Mass Type

Abstract. A Hygroscopicity Tandem Differential Mobility Analyser (HTDMA) was used to evaluate the hygroscopic properties of aerosol particles measured at the Puy de Dôme research station in central France, periodically from September 2008 to January 2010, and almost continuously from October 2010 to December 2012. This high-altitude site is ideally situated to allow for both the upper part of the planetary boundary layer and the lower free troposphere to be sampled. The aim of the study is to investigate both the influence of year-to-year, seasonal and diurnal cycles, as well as the influence of air mass type on particle hygroscopicity and mixing state. Results show that particle hygroscopicity increases with particle size and depends both on air mass type and on season. Average growth factor values, GFs, are lowest in winter (1.21 ± 0.13, 1.23 ± 0.18 and 1.38 ± 0.25 for 25, 50 and 165 nm particles, respectively) and highest in autumn (1.27 ± 0.11, 1.32 ± 0.12 and 1.49 ± 0.15 for 25, 50 and 165 nm particles, respectively). Particles are generally more hygroscopic at night than during the day. The seasonal and diurnal variations are likely to be strongly influenced by boundary layer dynamics. Furthermore, particles originating from oceanic and continental regions tend to be more hygroscopic than those measured in African and local air masses. The high hygroscopicity of oceanic aerosol can be explained by large proportions of inorganic aerosol and sea salts. Aerosols measured at the Puy de Dôme display a high degree of external mixing, and hygroscopic growth spectra can be divided into three different hygroscopic modes: a less-hygroscopic mode (GF < 1.3), a hygroscopic mode (GF~1.3–1.7) and a more-hygroscopic mode (GF > 1.7). The majority of particles measured can be classified as being in either the less-hygroscopic mode or the hygroscopic mode, and only few of them have more-hygroscopic properties. The degree of external mixing, evaluated as the fraction of time when the aerosol is found with two or more aerosol populations with different hygroscopic properties, increases with particle size (average yearly values are 20, 28 and 45 {%} for 25, 50, and 165 nm particles, respectively). The degree of external mixing is more sensitive to season than to air mass type, and it is higher in the cold seasons than in the warm seasons. With more than two years of nearly continuous measurements, this study gathers the results from one of the longest data sets of hygroscopic growth factor measurements to date, allowing a statistically relevant hygroscopic growth parameterization to be determined as a function of both air mass type and season.

Sign in / Sign up

Export Citation Format

Share Document