particle sizer
Recently Published Documents


TOTAL DOCUMENTS

386
(FIVE YEARS 83)

H-INDEX

39
(FIVE YEARS 4)

Materials ◽  
2022 ◽  
Vol 15 (2) ◽  
pp. 602
Author(s):  
Xixi Wu ◽  
Changjie Cai ◽  
Javier Gil ◽  
Elizabeth Jantz ◽  
Yacoub Al Sakka ◽  
...  

Titanium particles embedded on peri-implant tissues are associated with a variety of detrimental effects. Given that the characteristics of these detached fragments (size, concentration, etc.) dictate the potential cytotoxicity and biological repercussions exerted, it is of paramount importance to investigate the properties of these debris. This study compares the characteristics of particles released among different implant systems (Group A: Straumann, Group B: BioHorizons and Group C: Zimmer) during implantoplasty. A novel experimental system was utilized for measuring and collecting particles generated from implantoplasty. A scanning mobility particle sizer, aerodynamic particle sizer, nano micro-orifice uniform deposit impactor, and scanning electron microscope were used to collect and analyze the particles by size. The chemical composition of the particles was analyzed by highly sensitive microanalysis, microstructures by scanning electron microscope and the mechanical properties by nanoindentation equipment. Particles released by implantoplasty showed bimodal size distributions, with the majority of particles in the ultrafine size range (<100 nm) for all groups. Statistical analysis indicated a significant difference among all implant systems in terms of the particle number size distribution (p < 0.0001), with the highest concentration in Group B and lowest in Group C, in both fine and ultrafine modes. Significant differences among all groups (p < 0.0001) were also observed for the other two metrics, with the highest concentration of particle mass and surface area in Group B and lowest in Group C, in both fine and ultrafine modes. For coarse particles (>1 µm), no significant difference was detected among groups in terms of particle number or mass, but a significantly smaller surface area was found in Group A as compared to Group B (p = 0.02) and Group C (p = 0.005). The 1 first minute of procedures had a higher number concentration compared to the second and third minutes. SEM-EDS analysis showed different morphologies for various implant systems. These results can be explained by the differences in the chemical composition and microstructures of the different dental implants. Group B is softer than Groups A and C due to the laser treatment in the neck producing an increase of the grain size. The hardest implants were those of Group C due to the cold-strained titanium alloy, and consequently they displayed lower release than Groups A and B. Implantoplasty was associated with debris particle release, with the majority of particles at nanometric dimensions. BioHorizons implants released more particles compared to Straumann and Zimmer. Due to the widespread use of implantoplasty, it is of key importance to understand the characteristics of the generated debris. This is the first study to detect, quantify and analyze the debris/particles released from dental implants during implantoplasty including the full range of particle sizes, including both micro- and nano-scales.


Author(s):  
Gerrit J Jordaan ◽  
Wynand J vdM Steyn

: Nanotechnology options to road surface maintenance offers several advantages compared to traditionally used materials. The small particle sizer of hydrophobic Nano-Silane modified Nano-Polymers (NSNP) enables these nanotechnology products to deeply penetrate existing road surfaces, sealing micro-cracks and render surfacings to be water-resistant for extended periods of time. In comparison, traditionally used products contain minimum partial sizes of about 1 &ndash; 5 microns, that provide a superficial protection that wears off in a relatively short period of time. These traditional products are often associated with vehicle contamination while drying and requires the re-instatement of road markings. None of these disadvantages are associated with applicable NSNP technologies that are quick drying, with no vehicle contamination risks and is equivalent to a &ldquo;clear-seal&rdquo; requiring no reinstatement of road markings. In a similar vein, pot-hole repairs can be done using applicable, easy to use, pre-packed and treated pot-hole repair kits that are water-repellent and quick-drying at a fraction of the costs of conventional cold-mix products. Resurfacing using NME binder slurries can be done labour-intensively on a pre-treated NSNP surfacing, restoring cracked surfacing and providing a water-resistant long-lasting protective layer without the removal of existing cracked areas. The implementation of nanotechnology solutions for road surface maintenance operations is directly associated with ease of use, labour-intensive operations, prevention of considerable deterioration in riding quality due to removal and manual re-instatement of cracked surfaces, time and cost savings and a reduction in the risk of water damage to the sub-structure. TRANSLATE with x English ArabicHebrewPolish BulgarianHindiPortuguese CatalanHmong DawRomanian Chinese SimplifiedHungarianRussian Chinese TraditionalIndonesianSlovak CzechItalianSlovenian DanishJapaneseSpanish DutchKlingonSwedish EnglishKoreanThai EstonianLatvianTurkish FinnishLithuanianUkrainian FrenchMalayUrdu GermanMalteseVietnamese GreekNorwegianWelsh Haitian CreolePersian TRANSLATE with COPY THE URL BELOW Back EMBED THE SNIPPET BELOW IN YOUR SITE Enable collaborative features and customize widget: Bing Webmaster Portal Back


2021 ◽  
Author(s):  
Andrew James Shrimpton ◽  
Julian M Brown ◽  
Timothy M Cook ◽  
Chris M Penfold ◽  
Jonathan P Reid

Background: Open respiratory suctioning is considered to be an aerosol generating procedure (AGP) and laryngopharyngeal suction, used to clear secretions during anaesthesia, is widely managed as an AGP. It is uncertain whether such upper airway suctioning should be designated an aerosol generating procedure (AGP) because of a lack of both aerosol and epidemiological evidence of risk. Aim: To assess the relative risk of aerosol generation by upper airway suction during tracheal intubation and extubation in anaesthetised patients. Methods: Prospective environmental monitoring study in ultraclean operating theatres to assay aerosol concentration during intubation and extubation sequences including upper airway suctioning for patients undergoing surgery (n=19 patients). An Optical Particle Sizer (particle size 300nm-10μm) was used to sample aerosol 20cm above the mouth of the patient. Baseline recordings (background, tidal breathing and volitional coughs) were followed by intravenous induction of anaesthesia with neuromuscular blockade. Four periods of oropharyngeal suction were performed with a Yankauer sucker: pre-laryngoscopy, post-intubation and pre- and post-extubation. Findings: Aerosol from breathing was reliably detected (65[39-259] particles.L-1 (median[IQR])) above background (4.8[1-7] particles.L-1, p<0.0001 Friedman). The procedure of upper airway suction was associated with much lower average concentrations of aerosol than breathing (6.0[0-12] particles.L-1, P=0.0007) and was indistinguishable from background (P>0.99). The peak aerosol concentration recorded during suctioning (45[30-75] particles.L-1) was much lower than both volitional coughs (1520[600-4363] particles.L-1, p<0.0001, Friedman) and tidal breathing (540[300-1826] particles.L-1, p<0.0001, Friedman). Conclusion: The procedure of upper airway suction during airway management is associated with no higher concentration of aerosol than background and much lower than breathing and coughing. Upper airway suction should not be designated as a high risk AGP.  


2021 ◽  
Vol 14 (11) ◽  
pp. 7381-7404
Author(s):  
Steven G. Howell ◽  
Steffen Freitag ◽  
Amie Dobracki ◽  
Nikolai Smirnow ◽  
Arthur J. Sedlacek III

Abstract. The ultra-high-sensitivity aerosol spectrometer (UHSAS) differs from most other optical particle spectrometers by using a high-power infrared (IR) laser to detect small particles and reduce the sizing ambiguity due to the non-monotonicity of scattering with particle size. During the NASA ORACLES project (ObseRvations of Aerosols above CLouds and their intEractionS) over the southeast Atlantic Ocean, the UHSAS clearly undersized particles in the biomass burning plume extending from southern Africa. Since the horizontal and vertical extent of the plume was vast, the NASA P-3B research aircraft often flew through a fairly uniform biomass burning plume for periods exceeding 30 min, sufficient time to explore the details of the UHSAS response by selecting single particle sizes with a differential mobility analyzer (DMA) and passing them to the UHSAS. This was essentially an in-flight calibration of the UHSAS using the particles of interest. Two modes of responses appeared. Most particles were undersized by moderate amounts, ranging from not at all for 70 nm aerosols to 15 % for 280 nm particles. Mie scattering calculations show that composition-dependent refractive index of the particles cannot explain the pattern. Heating of brown carbon or tarballs in the beam causing evaporation and shrinking of the particles is the most plausible explanation, though mis-sizing due to non-sphericity cannot be ruled out. A small fraction (10 %–30 %) of the particles were undersized by 25 % to 35 %. Those were apparently the particles containing refractory black carbon. Laboratory calibrations confirm that black carbon is drastically undersized by the UHSAS, because particles heat to their vaporization point and shrink. A simple empirical correction equation was implemented that dramatically improves agreement with DMA distributions between 100 and 500 nm. It raised the median particle diameter by 18 nm, from 163 to 181 nm, during the August 2017 deployment and by smaller amounts during deployments with less intense pollution. Calculated scattering from UHSAS size distributions increased by about 130 %, dramatically improving agreement with scattering measured by nephelometers. The correction is only valid in polluted instances; clean marine boundary layer and free troposphere aerosols behaved more like the calibration spheres. We were unable to directly test the correction between 500 and 1000 nm, though aerodynamic particle sizer (APS) data appear to show that the correction is poor at the largest diameters, which is no surprise as the composition of those particles is likely to be quite different than that of the accumulation mode. This adds to the evidence that UHSAS data must be treated cautiously whenever the aerosol may absorb infrared light. Similar corrections may be required whenever brown carbon aerosol is present.


Author(s):  
James Sipich ◽  
Christian L'Orange ◽  
Kimberly Anderson ◽  
Christopher Limbach ◽  
John Volckens ◽  
...  

Thorax ◽  
2021 ◽  
pp. thoraxjnl-2021-217671
Author(s):  
Sadiyah Sheikh ◽  
Fergus W Hamilton ◽  
George W Nava ◽  
Florence K A Gregson ◽  
David T Arnold ◽  
...  

Pulmonary function tests are fundamental to the diagnosis and monitoring of respiratory diseases. There is uncertainty around whether potentially infectious aerosols are produced during testing and there are limited data on mitigation strategies to reduce risk to staff. Healthy volunteers and patients with lung disease underwent standardised spirometry, peak flow and FENO assessments. Aerosol number concentration was sampled using an aerodynamic particle sizer and an optical particle sizer. Measured aerosol concentrations were compared with breathing, speaking and voluntary coughing. Mitigation strategies included a standard viral filter and a full-face mask normally used for exercise testing (to mitigate induced coughing). 147 measures were collected from 33 healthy volunteers and 10 patients with lung disease. The aerosol number concentration was highest in coughs (1.45–1.61 particles/cm3), followed by unfiltered peak flow (0.37–0.76 particles/cm3). Addition of a viral filter to peak flow reduced aerosol emission by a factor of 10 without affecting the results. On average, coughs produced 22 times more aerosols than standard spirometry (with filter) in patients and 56 times more aerosols in healthy volunteers. FENO measurement produced negligible aerosols. Cardiopulmonary exercise test (CPET) masks reduced aerosol emission when breathing, speaking and coughing significantly. Lung function testing produces less aerosols than voluntary coughing. CPET masks may be used to reduce aerosol emission from induced coughing. Standard viral filters are sufficiently effective to allow guidelines to remove lung function testing from the list of aerosol-generating procedures.


Author(s):  
Enni Sanmark ◽  
Lotta-Maria A. H. Oksanen ◽  
Noora Rantanen ◽  
Mari Lahelma ◽  
Veli-Jukka Anttila ◽  
...  

Abstract Objective COVID-19 spreads through aerosols produced in coughing, talking, exhalation, and also in some surgical procedures. Use of CO2 laser in laryngeal surgery has been observed to generate aerosols, however, other techniques, such cold dissection and microdebrider, have not been sufficiently investigated. We aimed to assess whether aerosol generation occurs during laryngeal operations and the effect of different instruments on aerosol production. Methods We measured particle concentration generated during surgeries with an Optical Particle Sizer. Cough data collected from volunteers and aerosol concentration of an empty operating room served as references. Aerosol concentrations when using different techniques and equipment were compared with references as well as with each other. Results Thirteen laryngological surgeries were evaluated. The highest total aerosol concentrations were observed when using CO2 laser and these were significantly higher than the concentrations when using microdebrider or cold dissection (p < 0.0001, p < 0.0001) or in the background or during coughing (p < 0.0001, p < 0.0001). In contrast, neither microdebrider nor cold dissection produced significant concentrations of aerosol compared with coughing (p = 0.146, p = 0.753). In comparing all three techniques, microdebrider produced the least aerosol particles. Conclusions Microdebrider and cold dissection can be regarded as aerosol-generating relative to background reference concentrations, but they should not be considered as high-risk aerosol-generating procedures, as the concentrations are low and do not exceed those of coughing. A step-down algorithm from CO2 laser to cold instruments and microdebrider is recommended to lower the risk of airborne infections among medical staff.


2021 ◽  
pp. 00206-2021
Author(s):  
Runar Strand-Amundsen ◽  
Christian Tronstad ◽  
Ole Elvebakk ◽  
Tormod Martinsen ◽  
Marius Dybwad ◽  
...  

BackgroundOxygen delivering modalities like humidified high-flow nasal cannula (HFNC) and non-invasive positive-pressure ventilation (NIV) are suspected of generating aerosols that may contribute to transmission of disease such as COVID-19. We sought to assess if these modalities lead to increased aerosol dispersal compared to the use of non-humidified low-flow nasal cannula oxygen treatment (LFNC).MethodsAerosol dispersal from 20 healthy volunteers using HFNC, LFNC and NIV oxygen treatment was measured in a controlled chamber. We investigated effects related to coughing and using a surgical facemask in combination with the oxygen delivering modalities. An aerodynamic particle sizer measured aerosol particles (APS3321, 0.3–20 µm) directly in front of the subjects, while a mesh of smaller particle sensors (SPS30, 0.3–10 µm) was distributed in the test chamber.ResultsNon-productive coughing led to significant increases in particle dispersal close to the face when using LFNC and HFNC but not when using NIV. HFNC or NIV did not lead to a statistically significant increase in aerosol dispersal compared to LFNC. With non-productive cough in a room without air changes, there was a significant drop in particle levels between 100 cm and 180 cm from the subjects.ConclusionsOur results indicate that using HFNC and NIV does not lead to increased aerosol dispersal compared to low-flow oxygen treatment, except in rare cases. For a subject with non-productive cough, NIV with double-limb circuit and non-vented mask may be a favourable choice to reduce the risk for aerosol spread.


2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Sima Asadi ◽  
Manilyn J. Tupas ◽  
Ramya S. Barre ◽  
Anthony S. Wexler ◽  
Nicole M. Bouvier ◽  
...  

AbstractAnimal models are often used to assess the airborne transmissibility of various pathogens, which are typically assumed to be carried by expiratory droplets emitted directly from the respiratory tract of the infected animal. We recently established that influenza virus is also transmissible via “aerosolized fomites,” micron-scale dust particulates released from virus-contaminated surfaces (Asadi et al. in Nat Commun 11(1):4062, 2020). Here we expand on this observation, by counting and characterizing the particles emitted from guinea pig cages using an Aerodynamic Particle Sizer (APS) and an Interferometric Mie Imaging (IMI) system. Of over 9000 airborne particles emitted from guinea pig cages and directly imaged with IMI, none had an interference pattern indicative of a liquid droplet. Separate measurements of the particle count using the APS indicate that particle concentrations spike upwards immediately following animal motion, then decay exponentially with a time constant commensurate with the air exchange rate in the cage. Taken together, the results presented here raise the possibility that a non-negligible fraction of airborne influenza transmission events between guinea pigs occurs via aerosolized fomites rather than respiratory droplets, though the relative frequencies of these two routes have yet to be definitively determined.


2021 ◽  
Author(s):  
Enni Sanmark ◽  
Lotta-Maria Oksanen ◽  
Noora Rantanen ◽  
Mari Lahelma ◽  
Veli-Jukka Anttila ◽  
...  

ABSTRACT Aim: The purpose of the study was to determine aerosol exposure generated by coughing in operation room environments to create a quantitative limit value for high risk aerosol generating medical procedures. Background: Coughing is known to produce a significant amount of aerosols and is thus commonly used as a best reference for high-risk aerosol-generation. Accordingly, procedures during which aerosol generation exceeds the amount of aerosol generated in instances of coughing are seen as high risk aerosol generating procedures. However, no reliable quantitative values are available for high risk aerosol-generation. Methods: Coughing was measured from 37 healthy volunteers in the operating room environment. Aerosol particles generated during coughing within the size range of 0.3 - 10 microm were measured with Optical Particle Sizer from 40cm, 70cm, and 100cm distances. The distances reflected potential exposure distances where personnel are during surgeries. Results: A total of 306 coughs were measured. Average aerosol concentration during coughing was 1.580 +/- 13.774 particles/cm3 (range 0.000 - 195.528). Discussion: The aerosol concentration measured in this study can be used as a limit for high-risk aerosol generation in the operating room environment when assessing the aerosol generating procedures and the risk of operating room staff s exposure for aerosol particles. AUTHOR APPROVAL:All authors have approved the manuscript and have made significant contributions.


Sign in / Sign up

Export Citation Format

Share Document