scholarly journals Very high volume fly ash green concrete for applications in India

2018 ◽  
Vol 36 (6) ◽  
pp. 520-526 ◽  
Author(s):  
Jing Yu ◽  
Dhanada K Mishra ◽  
Chang Wu ◽  
Christopher KY Leung
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Power Plants ◽  
Thermal Power ◽  
High Volume ◽  
Practical Method ◽  
Green Concrete ◽  
High Volume Fly Ash ◽  
Binder Ratio ◽  
Target Characteristic

Safe disposal of fly ash generated by coal-based thermal power plants continues to pose significant challenges around the world and in India in particular. Green structural concrete with 80% cement replaced by local Chinese fly ash has been recently developed to achieve a target characteristic compressive strength of 45 MPa. Such green concrete mixes are not only cheaper in cost, but also embody lower energy and carbon footprint, compared with conventional mixes. This study aims to adopt such materials using no less than 80% fly ash as binder in routine concrete works in countries like India with the commonly used lower target characteristic compressive strength of 30 MPa. It is achieved by the simple and practical method of adjusting the water/binder ratio and/or superplasticiser dosage. The proposed green concrete shows encouraging mechanical properties at 7 days and 28 days, as well as much lower material cost and environmental impact compared with commercial Grade 30 concrete. This technology can play an important role in meeting the huge infrastructure demands in India in a sustainable manner.

scholarly journals Effect of Biomass Fly Ash on Fresh and Hardened Properties of High Volume Fly Ash Mortars

Crystals ◽  
2021 ◽  
Vol 11 (3) ◽  
pp. 233
Author(s):  
Elisabete R. Teixeira ◽  
Aires Camões ◽  
Fernando G. Branco ◽  
José Campos Matos
Keyword(s):  
Fly Ash ◽  
Power Plants ◽  
Coal Fly Ash ◽  
Thermal Power ◽  
High Volume ◽  
Hydrated Lime ◽  
Cement Replacement ◽  
High Volume Fly Ash ◽  
Hardened State ◽  
Biomass Fly Ash

The objective of this work was to assess the use of biomass fly ash (BFA) as cement replacement material or as an alkalinity source in high volume fly ash mortar and concrete. Mortar formulations were prepared with different types of cement replacement: fly ash from thermal power plants, BFA, a blend of two pozzolans, and small amounts of BFA or/and hydrated lime (HL). Mortar formulations were tested both in the fresh and hardened state. The replacement of cement by the two fly ashes led to a decrease in the mechanical strength. The best strength values were obtained when higher HL content was introduced in mortars, however, mortars with the lower BFA content presented the best results for the majority of the tests. In general, BFA has a similar effect on cementitious mortars to coal fly ash, having good performance as cement replacement.

scholarly journals A Study on the Evaluation of Field Application of High-Fluidity Concrete Containing High Volume Fly Ash

2015 ◽  
Vol 2015 ◽  
pp. 1-7
Author(s):  
Yun-Wang Choi ◽  
Man-Seok Park ◽  
Byung-Keol Choi ◽  
Sung-Rok Oh
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Drying Shrinkage ◽  
High Volume ◽  
Field Application ◽  
Heat Of Hydration ◽  
Economic Feasibility ◽  
High Volume Fly Ash ◽  
Alternative Materials ◽  
Binder Ratio

In the recent concrete industry, high-fluidity concrete is being widely used for the pouring of dense reinforced concrete. Normally, in the case of high-fluidity concrete, it includes high binder contents, so it is necessary to replace part of the cement through admixtures such as fly ash to procure economic feasibility and durability. This study shows the mechanical properties and field applicability of high-fluidity concrete using mass of fly ash as alternative materials of cement. The high-fluidity concrete mixed with 50% fly ash was measured to manufacture concrete that applies low water/binder ratio to measure the mechanical characteristics as compressive strength and elastic modulus. Also, in order to evaluate the field applicability, high-fluidity concrete containing high volume fly ash was evaluated for fluidity, compressive strength, heat of hydration, and drying shrinkage of concrete.

The Latest Research in Mongolia on the Utilization of Coal Combustion By-Products

2021 ◽  
Vol 323 ◽  
pp. 8-13
Author(s):  
Jadambaa Temuujin ◽  
Damdinsuren Munkhtuvshin ◽  
Claus H. Ruescher
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Coal Combustion ◽  
Power Plants ◽  
Thermal Power ◽  
Thermal Power Plants ◽  
Power Stations ◽  
Thermal Power Stations ◽  
Coal Ashes ◽  
By Products

With a geological reserve of over 170 billion tons, coal is the most abundant energy source in Mongolia with six operating thermal power stations. Moreover, in Ulaanbaatar city over 210000 families live in the Ger district and use over 800000 tons of coal as a fuel. The three thermal power plants in Ulaanbaatar burn about 5 million tons of coal, resulting in more than 500000 tons of coal combustion by-products per year. Globally, the ashes produced by thermal power plants, boilers, and single ovens pose serious environmental problems. The utilization of various types of waste is one of the factors determining the sustainability of cities. Therefore, the processing of wastes for re-use or disposal is a critical topic in waste management and materials research. According to research, the Mongolian capital city's air and soil quality has reached a disastrous level. The main reasons for air pollution in Ulaanbaatar are reported as being coal-fired stoves of the Ger residential district, thermal power stations, small and medium-sized low-pressure furnaces, and motor vehicles. Previously, coal ashes have been used to prepare advanced materials such as glass-ceramics with the hardness of 6.35 GPa, geopolymer concrete with compressive strength of over 30 MPa and zeolite A with a Cr (III) removal capacity of 35.8 mg/g. Here we discuss our latest results on the utilization of fly ash for preparation of a cement stabilized base layer for paved roads, mechanically activated fly ash for use in concrete production, and coal ash from the Ger district for preparation of an adsorbent. An addition of 20% fly ash to 5-8% cement made from a mixture of road base gave a compressive strength of ~ 4MPa, which exceeds the standard. Using coal ashes from Ger district prepared a new type of adsorbent material capable of removing various organic pollutants from tannery water was developed. This ash also showed weak leaching characteristics in water and acidic environment, which opens up an excellent opportunity to utilize.

Optimum Green Concrete Using Different High Volume Fly Ash Activated Systems

2017 ◽  
pp. 145-153
Author(s):  
Diego F. Velandia ◽  
Cyril J. Lynsdale ◽  
Fernando Ramirez ◽  
John L. Provis ◽  
German Hermida ◽  
...  
Keyword(s):  
Fly Ash ◽  
High Volume ◽  
Green Concrete ◽  
High Volume Fly Ash

scholarly journals Influence of Particle Size Distribution of High Calcium Fly Ash on HVFA Mortar Properties

2018 ◽  
Vol 20 (2) ◽  
pp. 51
Author(s):  
Antoni . ◽  
Hendra Surya Wibawa ◽  
Djwantoro Hardjito
Keyword(s):  
Particle Size ◽  
Compressive Strength ◽  
Fly Ash ◽  
Particle Size Distribution ◽  
Size Distribution ◽  
Setting Time ◽  
High Volume ◽  
High Volume Fly Ash ◽  
High Calcium ◽  
High Calcium Fly Ash

This study evaluates the effect of particle size distribution (PSD) of high calcium fly ash on high volume fly ash (HVFA) mortar characteristics. Four PSD variations of high calcium fly ash used were: unclassified fly ash and fly ash passing sieve No. 200, No. 325 and No. 400, respectively. The fly ash replacement ratio of the cementitious material ranged between 50-70%. The results show that with smaller fly ash particles size and higher levels of fly ash replacement, the workability of the mixture was increased with longer setting time. There was an increase in mortar compressive strength with finer fly ash particle size, compared to those with unclassified ones, with the highest strength was found at those with fly ash passing mesh No. 325. The increase was found due to better compactability of the mixture. Higher fly ash replacement reduced the mortar’s compressive strength, however, the rate was reduced when finer fly ash particles was used.

scholarly journals Development of High Volume Fly Ash Concrete Incorporating Steel Fibre

2020 ◽  
Vol 9 (2) ◽  
pp. 426-433
Keyword(s):  
Fly Ash ◽  
Aspect Ratio ◽  
Thermal Power ◽  
High Volume ◽  
Fine Aggregate ◽  
Fly Ash Concrete ◽  
High Volume Fly Ash ◽  
Hardened Properties ◽  
Very High ◽  
Split Tensile Test

Concrete is most frequently used composite material. Concrete is homogeneous mix of fine aggregate, Coarse aggregate and binding medium of concrete paste .Due to `high demand of cement Co2 emission is very high, It leads to global warming. So in this project high volume fly ash concrete was incorporated. Fly ash is the waste material obtained from thermal power plant. In this paper we investigated about high volume fly ash in different percentage of replacement 55, 60, 75 percentage. Layered pavement is incorporated with Steel fiber in a different aspect ratio (15, 30, 40).layered pavement will give good thermal expansive properties. By varying fly ash content and Steel fibers Aspect ratio of different mixes were arrived hardened properties of these nine mixes were arrived such as Compression test, Split tensile test and Flexural test.

RESEARCH OF COMPLEX MODIFICATION OF HEAVY CONCRETE

2021 ◽  
Vol 96 (4) ◽  
pp. 107-112
Author(s):  
YU.S. FILIMONOVA ◽  
◽  
E.G. VELICHKO ◽  
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Power Plants ◽  
High Efficiency ◽  
Thermal Power ◽  
Thermal Power Plants ◽  
Complex Chemical ◽  
Composition And Structure ◽  
Combined Use ◽  
Mineral Additive

Modification of the composition and structure of heavy concrete with the use of a complex chemical-mineral additive consisting of fly ash from thermal power plants, a superplasticizer, a high-valence hardening accelerator AC and a fine-dispersed clinker component is considered. Modified concrete is characterized by an increase in compressive strength at a brand age by 67%, a decrease in the water content of a concrete mixture by 13.6% and an improvement in its workability by 11-12 cm. With the combined use of a superplasticizer and a high-valence hardening accelerator AC a significant synergistic effect is observed in the format of enhancing their plasticizing effect. The high efficiency of the application of the mixed-dispersed clinker component has been established.

Sign in / Sign up

Export Citation Format

Share Document