Deformation and Stress Analysis of Supported Buttock Contact

1994 ◽  
Vol 208 (1) ◽  
pp. 9-17 ◽  
Author(s):  
P A Dabnichki ◽  
A D Crocombe ◽  
S C Hughes
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Shear Stress ◽  
Contact Problem ◽  
Stress Analysis ◽  
Stress Distributions ◽  
Body Segment ◽  
Element Analysis ◽  
Linear Finite Element ◽  
Support Surfaces

Non-linear finite element analysis has been used to investigate the contact problem between a buttock and a cushion of varying properties. The buttock tissue has been modelled on the macroscale by assuming it to be a hyperelastic (rubber-like) material with properties that correspond to the overall buttock response. Both rigid and flexible cushions have been considered. The contact between the cushion and the buttock has been modelled assuming both friction and friction-free conditions. The effect of these parameters on the buttock-cushion deformation and the tissue compressive and shear stress distributions have been presented. This study forms part of work towards the development of body segment simulators for use in investigations of seating and other support surfaces.

Stress analysis of axisymmetric butt joints loaded in torsion and tension

1978 ◽  
Vol 13 (1) ◽  
pp. 1-10 ◽  
Author(s):  
R D Adams ◽  
J Coppendale ◽  
N A Peppiatt
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Stress Concentration ◽  
Stress Analysis ◽  
Stress Distributions ◽  
Stress Concentrations ◽  
Adhesive Properties ◽  
Butt Joints ◽  
Element Analysis ◽  
Tensile Stresses

Axisymmetric butt joints are widely used as specimens for testing the response of adhesives to shear and tensile stresses. When analysing the results from these tests, the stress distributions must be accurately known. A finite-element analysis has been used to examine the effect of non-rigid adherends and a spew fillet in solid and annular butt joints for a range of geometries and adhesive properties. It has been shown that stress concentrations occur in butt joints loaded in tension; in the latter case, the stress concentration is directly due to the presence of the spew fillet.

Can Repeated Elastic Analyses Always Provide Exact Limit Loads?

2002 ◽  
Author(s):  
Prasad Mangalaramanan
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Shear Stress ◽  
Power Law ◽  
Elastic Moduli ◽  
Past Research ◽  
Stress Distributions ◽  
Element Analysis ◽  
Limit Loads ◽  
Beam Bending

Past research showed that obtaining statically admissible stress distributions based on elastic moduli modification methods exactly correspond to stress distributions due to stress-strain power law, for beam bending and cylinder under internal pressure. This paper investigates shear stress redistribution based on modified elastic moduli, theoretical and inelastic finite element analysis methods.

Finite Element Analysis of Tire/Rim Interface Forces Under Braking and Cornering Loads

1992 ◽  
Vol 20 (2) ◽  
pp. 83-105 ◽  
Author(s):  
J. P. Jeusette ◽  
M. Theves
Keyword(s):  
Finite Element ◽  
Shear Stress ◽  
Contact Pressure ◽  
Element Model ◽  
Shear Stresses ◽  
Detailed Knowledge ◽  
Stress Distributions ◽  
Element Analysis ◽  
Plane Shear ◽  
Normal Contact

Abstract During vehicle braking and cornering, the tire's footprint region may see high normal contact pressures and in-plane shear stresses. The corresponding resultant forces and moments are transferred to the wheel. The optimal design of the tire bead area and the wheel requires a detailed knowledge of the contact pressure and shear stress distributions at the tire/rim interface. In this study, the forces and moments obtained from the simulation of a vehicle in stationary braking/cornering conditions are applied to a quasi-static braking/cornering tire finite element model. Detailed contact pressure and shear stress distributions at the tire/rim interface are computed for heavy braking and cornering maneuvers.

scholarly journals Comparison of Tooth- and Bone-Borne Appliances on the Stress Distributions and Displacement Patterns in the Facial Skeleton in Surgically Assisted Rapid Maxillary Expansion—A Finite Element Analysis (FEA) Study

Materials ◽  
2021 ◽  
Vol 14 (5) ◽  
pp. 1152
Author(s):  
Rafał Nowak ◽  
Anna Olejnik ◽  
Hanna Gerber ◽  
Roman Frątczak ◽  
Ewa Zawiślak
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Three Dimensional ◽  
Element Model ◽  
Rapid Maxillary Expansion ◽  
Stress Distributions ◽  
Maxillary Expansion ◽  
Facial Skeleton ◽  
Element Analysis ◽  
Maxillary Constriction

The aim of this study was to compare the reduced stresses according to Huber’s hypothesis and the displacement pattern in the region of the facial skeleton using a tooth- or bone-borne appliance in surgically assisted rapid maxillary expansion (SARME). In the current literature, the lack of updated reports about biomechanical effects in bone-borne appliances used in SARME is noticeable. Finite element analysis (FEA) was used for this study. Six facial skeleton models were created, five with various variants of osteotomy and one without osteotomy. Two different appliances for maxillary expansion were used for each model. The three-dimensional (3D) model of the facial skeleton was created on the basis of spiral computed tomography (CT) scans of a 32-year-old patient with maxillary constriction. The finite element model was built using ANSYS 15.0 software, in which the computations were carried out. Stress distributions and displacement values along the 3D axes were found for each osteotomy variant with the expansion of the tooth- and the bone-borne devices at a level of 0.5 mm. The investigation showed that in the case of a full osteotomy of the maxilla, as described by Bell and Epker in 1976, the method of fixing the appliance for maxillary expansion had no impact on the distribution of the reduced stresses according to Huber’s hypothesis in the facial skeleton. In the case of the bone-borne appliance, the load on the teeth, which may lead to periodontal and orthodontic complications, was eliminated. In the case of a full osteotomy of the maxilla, displacements in the buccolingual direction for all the variables of the bone-borne appliance were slightly bigger than for the tooth-borne appliance.

Finite Element Analysis of Drum on the New Type Self-Driven Towing Machine for Cable

2011 ◽  
Vol 55-57 ◽  
pp. 664-669
Author(s):  
Jin Ning Nie ◽  
Hui Wang ◽  
De Feng Xie
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Stress Analysis ◽  
Compressive Stress ◽  
Wire Rope ◽  
Ansys Software ◽  
Element Analysis ◽  
Structure Improvement ◽  
Improvement Measures ◽  
New Type

According to the situation that the dual-friction drums on the new type towing machine lack stress analysis when designed, the safety is difficult to test and verify. The pull of wire rope in various positions was derived and calculated, so both compressive stress and tangent friction force generated by the pull of wire rope were calculated. The result made by ANSYS software demonstrates the safety of the left drum which suffers from larger loads, structure improvement measures are put forward for the drum.

Stress Analysis and Structure Optimization for the Opening Flat Cover of Pressure Vessels

2012 ◽  
Vol 538-541 ◽  
pp. 3253-3258 ◽  
Author(s):  
Jun Jian Xiao
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Stress Concentration ◽  
Stress Analysis ◽  
Structure Optimization ◽  
Pressure Vessels ◽  
Secondary Stress ◽  
Element Analysis ◽  
Primary Stress ◽  
Flat Cover

According to the results of finite element analysis (FEA), when the diameter of opening of the flat cover is no more than 0.5D (d≤0.5D), there is obvious stress concentration at the edge of opening, but only existed within the region of 2d. Increasing the thickness of flat covers could not relieve the stress concentration at the edge of opening. It is recommended that reinforcing element being installed within the region of 2d should be used. When the diameter of openings is larger than 0.5D (d>0.5D), conical or round angle transitions could be employed at connecting location, with which the edge stress decreased remarkably. However, the primary stress plus the secondary stress would be valued by 3[σ].

Specimen positioning effect on microshear test: Non-linear finite element analysis

2012 ◽  
Vol 28 ◽  
pp. e15-e16
Author(s):  
L.H.A. Raposo ◽  
L.C.M. Dantas ◽  
T.A. Xavier ◽  
A.G. Pereira ◽  
A. Versluis ◽  
...  
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Element Analysis ◽  
Linear Finite Element ◽  
Non Linear
Sign in / Sign up

Export Citation Format

Share Document