Effect of solidification mode on hot ductility of austenitic stainless steels

1983 ◽  
Vol 10 (1) ◽  
pp. 453-460 ◽  
Author(s):  
L. Myllykoski ◽  
N. Suutala
Keyword(s):  
Stainless Steels ◽  
Austenitic Stainless Steels ◽  
Hot Ductility ◽  
Solidification Mode

Hot Cracking Susceptibility in Duplex Stainless Steel Welds

2018 ◽  
Vol 941 ◽  
pp. 679-685
Author(s):  
Kazuyoshi Saida ◽  
Tomo Ogura
Keyword(s):  
Stainless Steels ◽  
Laser Beam Welding ◽  
Austenitic Stainless Steels ◽  
Hot Cracking ◽  
Duplex Stainless Steels ◽  
Solidification Cracking ◽  
Solidification Mode ◽  
Gas Tungsten Arc ◽  
Varestraint Test ◽  
Super Duplex Stainless Steels

The hot cracking (solidification cracking) susceptibility in the weld metals of duplex stainless steels were quantitatively evaluated by Transverse-Varestraint test with gas tungsten arc welding (GTAW) and laser beam welding (LBW). Three kinds of duplex stainless steels (lean, standard and super duplex stainless steels) were used for evaluation. The solidification brittle temperature ranges (BTR) of duplex stainless steels were 58K, 60K and 76K for standard, lean and super duplex stainless steels, respectively, and were comparable to those of austenitic stainless steels with FA solidification mode. The BTRs in LBW were 10-15K lower than those in GTAW for any steels. In order to clarify the governing factors of solidification cracking in duplex stainless steels, the solidification segregation behaviours of alloying and impurity elements were numerically analysed during GTAW and LBW. Although the harmful elements to solidification cracking such as P, S and C were segregated in the residual liquid phase in any joints, the solidification segregation of P, S and C in LBW was inhibited compared with GTAW due to the rapid cooling rate in LBW. It followed that the decreased solidification cracking susceptibility of duplex stainless steels in LBW would be mainly attributed to the suppression of solidification segregation of P, S and C.

Hot Ductility and Microstructure in Slab Shell of Low Ni Austenitic Stainless Steel

2013 ◽  
Vol 648 ◽  
pp. 3-6
Author(s):  
Guo Qing Hou ◽  
Liang Zhu
Keyword(s):  
Austenitic Stainless Steels ◽  
Solidification Process ◽  
Primary Phase ◽  
Hot Ductility ◽  
Test Results ◽  
Shell Surface ◽  
Solidification Mode ◽  
Δ Ferrite ◽  
The Difference ◽  
Reduction Of Area

Hot ductility in slab shell of two types of low Ni austenitic stainless steels was investigated via tensile test. Results showed that, reduction of area (RA) in Cr17Mn6Ni4Cu2N decreased gradually from surface to inside. However, RA in Cr15Mn9Cu2NiN shell surface was low, and increased from surface to inside. Analysis suggested that, the difference of RA between the two steels due to the different solidification process. In the shell of former steel, δ ferrite solidifies as the primary phase, then transforms into austenite. The space between primary arms increases from surface to inside, leading to the decrease of hot ductility. In the latter steel, δ ferrite does not solidify entirely as the primary phase because of the high cooling rate, but austenite solidifies directly from the retained liquid between δ ferrite dendrites. The change of solidification mode is most obviously in slab surface, which decreases its hot ductility.

Sign in / Sign up

Export Citation Format

Share Document