Three-dimensional texture determination of 6111 aluminium alloy sheet by precise serial sectioning and EBSD measurement

2005 ◽  
Vol 21 (4) ◽  
pp. 419-428 ◽  
Author(s):  
H. Jin ◽  
P. D. Wu ◽  
M. D. Ball ◽  
D. J. Lloyd
Keyword(s):  
Aluminium Alloy ◽  
Three Dimensional ◽  
Alloy Sheet ◽  
Serial Sectioning ◽  
Ebsd Measurement

THE DETERMINATION OF R-CURVES FOR SHORT, WIDE CENTRE CRACKED PANELS OF ALUMINIUM ALLOY SHEET

1991 ◽  
Vol 14 (8) ◽  
pp. 823-832
Author(s):  
G. R. Sutton ◽  
C. Wheeler ◽  
C. E. Thomas ◽  
R. N. Wilson
Keyword(s):  
Aluminium Alloy ◽  
Alloy Sheet

Conformation of Ribosomes from Escherichia Coli

1974 ◽  
Vol 32 ◽  
pp. 210-211
Author(s):  
M. Boublik ◽  
W. Hellmann ◽  
F. Jenkins
Keyword(s):  
Binding Sites ◽  
Ribosomal Proteins ◽  
Fluorescent Dyes ◽  
Protein Biosynthesis ◽  
Three Dimensional ◽  
Spatial Arrangement ◽  
Dimensional Structure ◽  
Complete Understanding ◽  
And Function

The present knowledge of the three-dimensional structure of ribosomes is far too limited to enable a complete understanding of the various roles which ribosomes play in protein biosynthesis. The spatial arrangement of proteins and ribonuclec acids in ribosomes can be analysed in many ways. Determination of binding sites for individual proteins on ribonuclec acid and locations of the mutual positions of proteins on the ribosome using labeling with fluorescent dyes, cross-linking reagents, neutron-diffraction or antibodies against ribosomal proteins seem to be most successful approaches. Structure and function of ribosomes can be correlated be depleting the complete ribosomes of some proteins to the functionally inactive core and by subsequent partial reconstitution in order to regain active ribosomal particles.

Analyzing the Impact of X-Ray Tomography on the Reliability of Integrated Circuits

2015 ◽  
Author(s):  
Halit Dogan ◽  
Md Mahbub Alam ◽  
Navid Asadizanjani ◽  
Sina Shahbazmohamadi ◽  
Domenic Forte ◽  
...  
Keyword(s):  
Integrated Circuits ◽  
Integrated Circuit ◽  
3D Imaging ◽  
Three Dimensional ◽  
Serial Sectioning ◽  
Promising Technique ◽  
Flash Memories ◽  
X Ray ◽  
3D Information ◽  
The Impact

Abstract X-ray tomography is a promising technique that can provide micron level, internal structure, and three dimensional (3D) information of an integrated circuit (IC) component without the need for serial sectioning or decapsulation. This is especially useful for counterfeit IC detection as demonstrated by recent work. Although the components remain physically intact during tomography, the effect of radiation on the electrical functionality is not yet fully investigated. In this paper we analyze the impact of X-ray tomography on the reliability of ICs with different fabrication technologies. We perform a 3D imaging using an advanced X-ray machine on Intel flash memories, Macronix flash memories, Xilinx Spartan 3 and Spartan 6 FPGAs. Electrical functionalities are then tested in a systematic procedure after each round of tomography to estimate the impact of X-ray on Flash erase time, read margin, and program operation, and the frequencies of ring oscillators in the FPGAs. A major finding is that erase times for flash memories of older technology are significantly degraded when exposed to tomography, eventually resulting in failure. However, the flash and Xilinx FPGAs of newer technologies seem less sensitive to tomography, as only minor degradations are observed. Further, we did not identify permanent failures for any chips in the time needed to perform tomography for counterfeit detection (approximately 2 hours).

scholarly journals Mechanical clinching and self-pierce riveting for sheet combination of 780-MPa high-strength steel and aluminium alloy A5052 sheets and durability on salt spray test of joints

2021 ◽  
Vol 113 (1-2) ◽  
pp. 59-72
Author(s):  
Yohei Abe ◽  
Ken-ichiro Mori
Keyword(s):  
Aluminium Alloy ◽  
High Strength Steel ◽  
Salt Spray ◽  
High Strength ◽  
Alloy Sheet ◽  
Galvanized Steel ◽  
Load Reduction ◽  
Minimum Thickness ◽  
Steel Sheets ◽  
Mechanical Clinching

AbstractTo increase the usage of high-strength steel and aluminium alloy sheets for lightweight automobile body panels, the joinability of sheet combinations including a 780-MPa high-strength steel and an aluminium alloy A5052 sheets by mechanical clinching and self-pierce riveting was investigated for different tool shapes in an experiment. All the sheet combinations except for the two steel sheets by self-pierce riveting, i.e., the two steel sheets, the two aluminium alloy sheets, and the steel-aluminium alloy sheets, were successfully joined by both the joining methods without the gaps among the rivet and the sheets. Then, to show the durability of the joined sheets, the corrosion behaviour and the joint strength of the aged sheets by a salt spray test were measured. The corrosion and the load reduction of the clinched and the riveted two aluminium alloy sheets were little. The corrosion of the clinched two steel sheets without the galvanized layer progressed, and then the load after 1176 h decreased by 85%. In the clinched two galvanized steel sheets, the corrosion progress slowed down by 24%. In the clinched steel and aluminium alloy sheets, the thickness reduction occurred near the minimum thickness of the upper sheet and in the upper surface on the edge of the lower aluminium alloy sheet, whereas the top surface of the upper sheet and the upper surface of the lower sheet were mainly corroded in the riveted joint. The load reduction was caused by the two thickness reductions, i.e., the reduction in the minimum thickness of the upper sheet and the reduction in the flange of the aluminium alloy sheet. Although the load of the clinched steel without the galvanized coating layer and aluminium alloy sheets decreased by about 20%, the use of the galvanized steel sheet brought the decrease by about 11%. It was found that the use of the galvanized steel sheets is effective for the decrease of strength reduction due to corrosion.

scholarly journals Meso-Scale Transmission Electron Microscope Tomography Applied for Wax Distribution in Toner Particles

2013 ◽  
Vol 19 (S5) ◽  
pp. 58-61 ◽  
Author(s):  
Mino Yang ◽  
Jun-Ho Lee ◽  
Hee-Goo Kim ◽  
Euna Kim ◽  
Young-Nam Kwon ◽  
...  
Keyword(s):  
Electron Microscope ◽  
Transmission Electron Microscope ◽  
Three Dimensional ◽  
Chromatic Aberration ◽  
Laser Printer ◽  
Medium Voltage ◽  
Transmission Electron ◽  
Z Contrast ◽  
Contrast Image

AbstractDistribution of wax in laser printer toner was observed using an ultra-high-voltage (UHV) and a medium-voltage transmission electron microscope (TEM). As the radius of the wax spans a hundred to greater than a thousand nanometers, its three-dimensional recognition via TEM requires large depth of focus (DOF) for a volumetric specimen. A tomogram with a series of the captured images would allow the determination of their spatial distribution. In this study, bright-field (BF) images acquired with UHV-TEM at a high tilt angle prevented the construction of the tomogram. Conversely, the Z-contrast images acquired by the medium-voltage TEM produced a successful tomogram. The spatial resolution for both is discussed, illustrating that the image degradation was primarily caused by beam divergence of the Z-contrast image and the combination of DOF and chromatic aberration of the BF image from the UHV-TEM.

Sign in / Sign up

Export Citation Format

Share Document