Locating faults in underground coal mines using high‐resolution seismic reflection techniques

Geophysics ◽  
1989 ◽  
Vol 54 (12) ◽  
pp. 1521-1527 ◽  
Author(s):  
Lawrence M. Gochioco ◽  
Steven A. Cotten
Keyword(s):  
High Resolution ◽  
Seismic Data ◽  
Seismic Reflection ◽  
Coal Mines ◽  
Seismic Source ◽  
Seismic Survey ◽  
Underground Coal Mines ◽  
Vertical Displacements ◽  
Seismic Sections ◽  
Mine Development

A high‐resolution seismic reflection technique was used to locate faults in coal seams that were not visible on the surface and could only be observed in underground coal mines. An 8‐gauge buffalo gun, built by the research and development department of Consolidation Coal Company, was used as the seismic source. The coal seam at a depth of 700 ft produces a reflection with a predominant frequency of about 125 Hz. The high‐resolution seismic data permitted faults with vertical displacements of the same magnitude as the seam thickness to be detected at depths of several hundred feet beneath the surface. Several faults were detected and interpreted from the seismic sections, and the magnitudes of their displacement were estimated by matching the recorded seismic data to synthetic seismic data. Subsequent underground mine development in the study area confirmed two interpreted faults and their estimated displacements. Mining engineers were able to use the information provided by the seismic survey to plan an entry system through the fault zone so that less rock needed to be mined, resulting in a safer and more productive mine.

High‐resolution 3-D seismic survey over a coal mine reserve area in the U.S.—A case study

Geophysics ◽  
2000 ◽  
Vol 65 (3) ◽  
pp. 712-718 ◽  
Author(s):  
Lawrence M. Gochioco
Keyword(s):  
High Resolution ◽  
Coal Mine ◽  
Seismic Data ◽  
Longwall Mining ◽  
Three Dimensional ◽  
Seismic Source ◽  
Seismic Survey ◽  
Geologic Structure ◽  
Reserve Area ◽  
Mine Development

A high‐resolution three‐dimensional (3-D) seismic survey was conducted in advance of coal mine development in the Illinois basin in May 1989 to better define a geologic structure with the potential to adversely affect longwall mining conditions. The 3-D seismic data indicate that an abrupt change in seam elevation, or roll, encountered near the northern property line trends south into the reserve area and then turns southeast. A personal computer‐based workstation was used to integrate borehole and seismic data for modeling in which 3-D block diagrams of the calculated seam elevations were generated. The block diagrams show a steep slope on the west flank of the roll that gradually decreases as the roll turns to the southeast. The survey also reveals a geologic structure beneath the roll at an estimated depth of 46–62 m. Horizontal time‐slice sections of this feature suggest the presence of a paleochannel that meanders on a similar course as the roll, which apparently was connected to a larger paleochannel system. A Conoco high‐frequency vibroseis unit was successfully used as the seismic source to generate the high frequencies necessary to detect and resolve the thin coal beds.

A comparative study of multi-scaled high-resolution seismic surveys in shallow marine environments: examples from three sites, offshore Korea

2020 ◽  
Author(s):  
Young Jun Kim ◽  
Snons Cheong ◽  
Deniz Cukur ◽  
Dong-Geun Yoo
Keyword(s):  
High Resolution ◽  
Data Processing ◽  
Seismic Data ◽  
Single Channel ◽  
Seismic Source ◽  
Seismic Survey ◽  
Minimum Length ◽  
Seismic Surveys ◽  
Air Gun ◽  
Target Depth

<p>In marine seismic surveys, various acquisition systems are used depending on the survey purpose, target depth, survey environment, and conditions. A 3D survey of oil and/or gas exploration, for instance, require large-capacity air-gun arrays and six or more streamers with a minimum length of 6 km. In contrast, a high-resolution seismic survey for the shallow-water geological research and engineering needs a small capacity source such as air-gun, sparker, and boomer, deployed with a single-channel or multi-channel (24-channel) streamers. The main purpose of our seismic survey was to investigate the Quaternary geology and stratigraphy of offshore, Korea. Because the Quaternary is the most recent geological period, our target depth was very shallow at about 50 m below the sea-bottom. We used a high-frequency seismic source including a sparker of 2,000 J capacity or a 60 in<sup>3</sup> mini GI-gun and an eight-channel streamer with a 3.125 m group interval or a single-channel streamer that included 96 elements. To compare the resolution of seismic data according to the seismic source, a boomer or sparker systems were used with the single-channel streamer on a small survey ship. The seismic data processing was performed at the Korea Institute of Geoscience and Mineral Resources (KIGAM) with ProMAX, and the data processing and resolution of each survey were compared based on their acquisition systems.</p>

Late Cretaceous – Cenozoic history of the transition zone between the East European Craton and the Paleozoic Platform, Polish sector of the Baltic Sea, revealed by new offshore regional seismic reflection data (BALTEC project)

2021 ◽  
Author(s):  
Piotr Krzywiec ◽  
Łukasz Słonka ◽  
Quang Nguyen ◽  
Michał Malinowski ◽  
Mateusz Kufrasa ◽  
...  
Keyword(s):  
High Resolution ◽  
Late Cretaceous ◽  
Seismic Data ◽  
Seismic Reflection ◽  
Upper Cretaceous ◽  
Seismic Reflection Data ◽  
East European ◽  
Reflection Data ◽  
Multichannel Seismic Reflection ◽  
Multichannel Seismic Reflection Data

<p>In 2016, approximately 850 km of high-resolution multichannel seismic reflection data of the BALTEC survey have been acquired offshore Poland within the transition zone between the East European Craton and the Paleozoic Platform. Data processing, focused on removal of multiples, strongly overprinting geological information at shallower intervals, included SRME, TAU-P domain deconvolution, high resolution parabolic Radon demultiple and SWDM (Shallow Water De-Multiple). Entire dataset was Kirchhoff pre-stack time migrated. Additionally, legacy shallow high-resolution multichannel seismic reflection data acquired in this zone in 1997 was also used. All this data provided new information on various aspects of the Phanerozoic evolution of this area, including Late Cretaceous to Cenozoic tectonics and sedimentation. This phase of geological evolution could be until now hardly resolved by analysis of industry seismic data as, due to limited shallow seismic imaging and very strong overprint of multiples, essentially no information could have been retrieved from this data for first 200-300 m. Western part of the BALTEC dataset is located above the offshore segment of the Mid-Polish Swell (MPS) – large anticlinorium formed due to inversion of the axial part of the Polish Basin. BALTEC seismic data proved that Late Cretaceous inversion of the Koszalin – Chojnice fault zone located along the NE border of the MPS was thick-skinned in nature and was associated with substantial syn-inversion sedimentation. Subtle thickness variations and progressive unconformities imaged by BALTEC seismic data within the Upper Cretaceous succession in vicinity of the Kamień-Adler and the Trzebiatów fault zones located within the MPS documented complex interplay of Late Cretaceous basin inversion, erosion and re-deposition. Precambrian basement of the Eastern, cratonic part of the study area is overlain by Cambro-Silurian sedimentary cover. It is dissected by a system of steep, mostly reverse faults rooted in most cases in the deep basement. This fault system has been regarded so far as having been formed mostly in Paleozoic times, due to the Caledonian orogeny. As a consequence, Upper Cretaceous succession, locally present in this area, has been vaguely defined as a post-tectonic cover, locally onlapping uplifted Paleozoic blocks. New seismic data, because of its reliable imaging of the shallowest substratum, confirmed that at least some of these deeply-rooted faults were active as a reverse faults in latest Cretaceous – earliest Paleogene. Consequently, it can be unequivocally proved that large offshore blocks of Silurian and older rocks presently located directly beneath the Cenozoic veneer must have been at least partly covered by the Upper Cretaceous succession; then, they were uplifted during the widespread inversion that affected most of Europe. Ensuing regional erosion might have at least partly provided sediments that formed Upper Cretaceous progradational wedges recently imaged within the onshore Baltic Basin by high-end PolandSPAN regional seismic data. New seismic data imaged also Paleogene and younger post-inversion cover. All these results prove that Late Cretaceous tectonics substantially affected large areas located much farther towards the East than previously assumed.</p><p>This study was funded by the Polish National Science Centre (NCN) grant no UMO-2017/27/B/ST10/02316.</p>

DEMETER HIGH RESOLUTION 3D SEISMIC SURVEY—REVITALISED DEVELOPMENT AND EXPLORATION ON THE NORTH WEST SHELF, AUSTRALIA

2006 ◽  
Vol 46 (1) ◽  
pp. 101 ◽  
Author(s):  
K.J. Bennett ◽  
M.R. Bussell
Keyword(s):  
High Resolution ◽  
Seismic Data ◽  
New Technologies ◽  
Seismic Survey ◽  
Future Application ◽  
3D Seismic ◽  
Gas Field ◽  
North West ◽  
The North ◽  
Exploration And Development

The newly acquired 3,590 km2 Demeter 3D high resolution seismic survey covers most of the North West Shelf Venture (NWSV) area; a prolific hydrocarbon province with ultimate recoverable reserves of greater than 30 Tcf gas and 1.5 billion bbls of oil and natural gas liquids. The exploration and development of this area has evolved in parallel with the advent of new technologies, maturing into the present phase of revitalised development and exploration based on the Demeter 3D.The NWSV is entering a period of growing gas market demand and infrastructure expansion, combined with a more diverse and mature supply portfolio of offshore fields. A sequence of satellite fields will require optimised development over the next 5–10 years, with a large number of wells to be drilled.The NWSV area is acknowledged to be a complex seismic environment that, until recently, was imaged by a patchwork of eight vintage (1981–98) 3D seismic surveys, each acquired with different parameters. With most of the clearly defined structural highs drilled, exploration success in recent years has been modest. This is due primarily to severe seismic multiple contamination masking the more subtle and deeper exploration prospects. The poor quality and low resolution of vintage seismic data has also impeded reservoir characterisation and sub-surface modelling. These sub-surface uncertainties, together with the large planned expenditure associated with forthcoming development, justified the need for the Demeter leading edge 3D seismic acquisition and processing techniques to underpin field development planning and reserves evaluations.The objective of the Demeter 3D survey was to re-image the NWSV area with a single acquisition and processing sequence to reduce multiple contamination and improve imaging of intra-reservoir architecture. Single source (133 nominal fold), shallow solid streamer acquisition combined with five stages of demultiple and detailed velocity analysis are considered key components of Demeter.The final Demeter volumes were delivered early 2005 and already some benefits of the higher resolution data have been realised, exemplified in the following:Successful drilling of development wells on the Wanaea, Lambert and Hermes oil fields and identification of further opportunities on Wanaea-Cossack and Lambert- Hermes;Dramatic improvements in seismic data quality observed at the giant Perseus gas field helping define seven development well locations;Considerably improved definition of fluvial channel architecture in the south of the Goodwyn gas field allowing for improved well placement and understanding of reservoir distribution;Identification of new exploration prospects and reevaluation of the existing prospect portfolio. Although the Demeter data set has given significant bandwidth needed for this revitalised phase of exploration and development, there remain areas that still suffer from poor seismic imaging, providing challenges for the future application of new technologies.

scholarly journals Seismic reflection imaging of a geothermal aquifer in an urban setting

Geophysics ◽  
1998 ◽  
Vol 63 (4) ◽  
pp. 1285-1294 ◽  
Author(s):  
Lee Liberty
Keyword(s):  
Seismic Reflection ◽  
Seismic Source ◽  
Urban Setting ◽  
Seismic Survey ◽  
Quality Data ◽  
Signal Quality ◽  
Fracture Permeability ◽  
Air Gun ◽  
Explosive Source ◽  
Geothermal Aquifer

A seismic reflection survey that was conducted in downtown Boise, Idaho, to help city planners site a new well for injection of spent geothermal water illustrates some methods to safely and successfully employ a seismic reflection survey in an urban setting. The objective of the seismic survey was to estimate the depth and continuity of a basalt and rhyolite volcanic sequence. Well siting was based on geothermal aquifer depth, location of interpreted faults, projected thermal impact of injection on existing wells, surface pipe extension costs, and public land availability. Seismic acquisition tests and careful processing were used to ensure high‐quality data while minimizing the potential for damage along city streets. A video camera placed in a sewer and a blast vibration monitor were used to confirm that energy from the seismic source (a 75-in3 land air gun) did not damage nearby buildings, street surfaces, or buried utilities along the survey lines. Walkaway seismic tests were also used to compare signal quality of the air‐gun source to an explosive source for imaging targets up to 800 m depth. These tests show less signal bandwidth from the air‐gun source compared to the buried explosive source, but the air‐gun signal quality was adequate to meet imaging objectives. Seismic reflection results show that the top of this rhyolite/basalt sequence dips (∼8–11°) southwest away from the Boise foothills at depths of 200 to 800 m. Seismic methods enabled interpretation of aquifer depths along the profiles and located fault zones where injected water may encounter fracture permeability and optimally benefit the existing producing system. The acquisition and processing techniques used to locate the Boise injection well may succeed for other hydrogeologic and environmental studies in urban settings.

Seismic reflection profiles across the "Mine Series" in the Noranda camp of the Abitibi belt, eastern Canada

1995 ◽  
Vol 32 (2) ◽  
pp. 167-176 ◽  
Author(s):  
Pierre Verpaelst ◽  
A. Shirley Péloquin ◽  
Erick Adam ◽  
Arthur E. Barnes ◽  
John N. Ludden ◽  
...  
Keyword(s):  
High Resolution ◽  
Seismic Reflection ◽  
Mineral Exploration ◽  
Drill Hole ◽  
Seismic Survey ◽  
Volcanic Complex ◽  
Eastern Canada ◽  
Crustal Layer ◽  
High Resolution Data ◽  
Seismic Reflection Profiles

The Abitibi–Grenville Lithoprobe project completed a regional (line 21) and a high-resolution (line 21-1) seismic survey in the Noranda Central Volcanic Complex of the Blake River Group, Abitibi, Quebec. Line 21 provides a regional framework in which the Archean crust is divided into three layers, two of which are discussed here: the uppermost layer, which corresponds to the Blake River Group, is the least reflective, and lies above 4 s (12 km), and the mid-crustal layer, which is composed of a complex pattern of generally east-northeast-dipping reflectors and lies between 4 and 8 s. Within the regional data, the Mine Series of the Central Volcanic Complex is imaged as a semitransparent series of reflectors overlying a highly reflective east-facing structure interpreted as the subvolcanic Flavrian pluton. The high-resolution data (line 21-1) were collected in the vicinity of the Ansil mine. The seismic images in this region can be controlled by surface geology and extensive drill-hole data, and the project was designed to test the applicability of seismic reflection profiling in providing structural and stratigraphic information for use in mineral exploration: shallow-dipping reflectors correlate well with lithological variations or contacts in the volcanic sequence; strong subhorizontal reflectors correspond to diorite and gabbro dykes and sills; several abrupt lateral changes in the reflectivity coincide with known intrusive contacts such as the Lac Dufault pluton.

Seismic reflection constraints on upper crustal structures in the volcanic-covered central Nechako basin, British Columbia1This article is one of a series of papers published in this Special Issue on the theme of New insights in Cordilleran Intermontane geoscience: reducing exploration risk in the mountain pine beetle-affected area, British Columbia.

2011 ◽  
Vol 48 (6) ◽  
pp. 1021-1037 ◽  
Author(s):  
A.J. Calvert ◽  
N.E. Hayward ◽  
J.E. Spratt ◽  
J.A. Craven
Keyword(s):  
British Columbia ◽  
Seismic Data ◽  
Seismic Reflection ◽  
Mountain Pine Beetle ◽  
Volcanic Rocks ◽  
Seismic Survey ◽  
Volcanic Stratigraphy ◽  
Exploration Risk ◽  
Good Signal ◽  
Lower Crustal

In 2008, a Vibroseis seismic reflection survey was acquired by Geoscience BC across the eastern part of the volcanic-covered Nechako basin in central British Columbia, where Cretaceous sedimentary rocks have been exhumed along a NNW trend. Good signal penetration through the volcanic cover is indicated by lower crustal reflections at 8–12 s, which were recorded by the entire seismic survey. Comparison of the 2008 seismic survey with data from a previous survey indicates that the lack of reflectivity in the earlier surveys is generally representative of the subsurface geology. The seismic data show that ∼1700 and ∼2900 m thick sub-basins are present at the northern and southern ends of this trend, but the intervening Cretaceous rocks are discontinuous and relatively thin. The creation of a passive-roof duplex by Campanian or later low-angle thrusting is inferred within the thickest Cretaceous strata, but elsewhere faulting is likely related to Eocene extension or transtension. Seismic reflections are also recorded from folded volcanic stratigraphy, the base of the surface volcanic rocks, an underlying volcaniclastic stratigraphy, and intrusions projecting into a Quaternary volcanic cone. Seismic interpretation is complemented by coincident audiofrequency magnetotelluric surveys, from which faulting is inferred at offsets in a regional conductor. No regionally extensive stratigraphy can be identified within the seismic data, and the central Nechako basin appears to be a complex network of small, deformed sub-basins, rather than a single large basin.

Sign in / Sign up

Export Citation Format

Share Document