Multidisciplinary Analysis of Hydraulic Stimulation and Production Effects within the Niobrara and Codell Reservoirs, Wattenberg Field, Colorado: Part 1 - Baseline Reservoir Conditions

2021 ◽  
pp. 1-41
Author(s):  
Matthew Bray ◽  
Jacquelyn Daves ◽  
Daniel Brugioni ◽  
Asm Kamruzzaman ◽  
Tom Bratton ◽  
...  
Keyword(s):  
Hydraulic Fracturing ◽  
Seismic Data ◽  
Time Lapse ◽  
Organic Content ◽  
P Wave ◽  
Seismic Survey ◽  
Fracture Density ◽  
Niobrara Formation ◽  
Reservoir Properties ◽  
Wattenberg Field

In the Wattenberg Field, the Reservoir Characterization Project at the Colorado School of Mines and Occidental Petroleum Corporation (Oxy) (formerly the Anadarko Petroleum Corporation) collected time-lapse seismic data for characterization of changes in the reservoir caused by hydraulic fracturing and production in the Niobrara Formation and Codell Sandstone member of the Carlile Formation. We have acquired three multicomponent seismic surveys to understand the dynamic reservoir changes caused by hydraulic fracturing and production of 11 horizontal wells within a 1 mi2 section (the Wishbone Section). The time-lapse seismic survey acquisition occurred immediately after the wells were drilled, another survey after stimulation, and a third survey after two years of production. In addition, we integrate core, petrophysical properties, fault and fracture characteristics, as well as P-wave seismic data to illustrate reservoir properties prior to simulation and production. Core analysis indicates extensive amounts of bioturbation in zones of high total organic content (TOC). Petrophysical analysis of logs and core samples indicates that chalk intervals have high amounts of TOC (>2%) and the lowest amount of clay in the reservoir interval. Core petrophysical characterization included X-ray diffraction analysis, mercury intrusion capillary pressure, N2 gas adsorption, and field emission scanning electron microscopy. Reservoir fractures follow four regional orientations, and chalk facies contain higher fracture density than marl facies. Integration of these data assist in enhanced well targeting and reservoir simulation.

Multidisciplinary Analysis of Hydraulic Stimulation and Production Effects within the Niobrara and Codell Reservoirs, Wattenberg Field, Colorado: Part 2 — Analysis of Hydraulic Fracturing and Production

2021 ◽  
pp. 1-53
Author(s):  
Matthew Bray ◽  
Jakob Utley ◽  
Yanrui Ning ◽  
Angela Dang ◽  
Jacquelyn Daves ◽  
...  
Keyword(s):  
Hydraulic Fracturing ◽  
Seismic Data ◽  
Time Lapse ◽  
Production Performance ◽  
P Wave ◽  
Production Data ◽  
Total Production ◽  
Wattenberg Field ◽  
Reservoir Models ◽  
3D Geomechanical Model

Enhanced hydrocarbon recovery is essential for continued economic development of unconventional reservoirs. Our study focuses on dynamic characterization of the Niobrara and Codell Formations in Wattenberg Field through the development and analysis of a full integrated reservoir model. We demonstrate the effectiveness of hydraulic fracturing and production with two seismic monitor surveys, surface microseismic, completion data, and production data. The two monitor surveys were recorded after stimulation, and again after two years of production. Identification of reservoir deformation due to hydraulic fracturing and production improves reservoir models by mapping non-stimulated and non-producing zones. Monitoring these time-variant changes improves the prediction capability of reservoir models, which in turn leads to improved well and stage placement. We quantify dynamic reservoir changes with time-lapse P-wave seismic data utilizing pre-stack inversion, and velocity-independent layer stripping for velocity and attenuation changes within the Niobrara and Codell reservoirs. A 3D geomechanical model and production data are history matched, and a simulation is run for two years of production. Results are integrated with time-lapse seismic data to illustrate the effects of hydraulic fracturing and production. Our analyses illustrate that chalk facies have significantly higher hydraulic fracture efficiency and production performance than marl facies. Additionally, structural and hydraulic complexity associated with faults generate spatial variability in a well’s total production.

Multicomponent 3-D characterization of a coalbed methane reservoir

Geophysics ◽  
1996 ◽  
Vol 61 (2) ◽  
pp. 315-330 ◽  
Author(s):  
Edward L. Shuck ◽  
Thomas L. Davis ◽  
Robert D. Benson
Keyword(s):  
Shear Wave ◽  
Seismic Data ◽  
Coalbed Methane ◽  
Accurate Determination ◽  
P Wave ◽  
Seismic Survey ◽  
Fracture Density ◽  
Structural Interpretation ◽  
Coalbed Methane Reservoir

Methane is produced from fractured coalbed reservoirs at Cedar Hill Field in the San Juan Basin. Fracturing and local stress are critical to production because of the absence of matrix permeability in the coals. Knowledge of the direction of open fractures, the degree of fracturing, reservoir pressure, and compartmentalization is required to understand the flow of fluids through the reservoir. A multicomponent 3-D seismic survey was acquired to aid in coalbed methane reservoir characterization. Coalbed reservoir heterogeneities, including isolated pressure cells, zones of increased fracture density, and variable fracture directions, have been interpreted through the analysis of the multicomponent data and integration with petrophysical and reservoir engineering studies. Strike‐slip faults, which compartmentalize the reservoir, have been identified by structural interpretation of the 3-D P‐wave seismic data. These faults form boundaries for pressure cells that have been identified by P‐wave reflection amplitude anomalies. The analysis of polarizations, traveltimes, and reflection amplitudes from the shear‐wave seismic data has allowed the identification of zones of variable fracture direction and fracture density. There is good agreement between stresses inferred from the structural interpretation and those indicated by the shear‐wave polarizations. Reflection amplitudes have been calibrated to seismic velocities and reservoir pressures through the use of petrophysical data taken from core samples. New methods have been developed for the statistical analysis of prestack shear‐wave polarizations, poststack polarizations, and the accurate determination of traveltime anisotropy. The prestack polarization analysis method allows for rapid and efficient determination of a dominant polarization direction. Shear‐wave anisotropy has been quantified over the reservoir zone using both traveltime and thin‐bed reflection response with excellent agreement between the two methods. Crack densities computed from the anisotropy show two regions of high crack density, one coinciding with a sealed overpressured cell and the other in the region of the Hamilton ♯3 well. This indicates the potential for monitoring production of coalbed methane reservoirs using multicomponent seismology.

Dense surface seismic data confirm non-double-couple source mechanisms induced by hydraulic fracturing

Geophysics ◽  
2016 ◽  
Vol 81 (6) ◽  
pp. KS207-KS217 ◽  
Author(s):  
Jeremy D. Pesicek ◽  
Konrad Cieślik ◽  
Marc-André Lambert ◽  
Pedro Carrillo ◽  
Brad Birkelo
Keyword(s):  
Hydraulic Fracturing ◽  
Seismic Data ◽  
P Wave ◽  
Source Modeling ◽  
Moment Tensors ◽  
Amplitude Data ◽  
Double Couple ◽  
Source Mechanisms ◽  
Source Models ◽  
Favorable Conditions

We have determined source mechanisms for nine high-quality microseismic events induced during hydraulic fracturing of the Montney Shale in Canada. Seismic data were recorded using a dense regularly spaced grid of sensors at the surface. The design and geometry of the survey are such that the recorded P-wave amplitudes essentially map the upper focal hemisphere, allowing the source mechanism to be interpreted directly from the data. Given the inherent difficulties of computing reliable moment tensors (MTs) from high-frequency microseismic data, the surface amplitude and polarity maps provide important additional confirmation of the source mechanisms. This is especially critical when interpreting non-shear source processes, which are notoriously susceptible to artifacts due to incomplete or inaccurate source modeling. We have found that most of the nine events contain significant non-double-couple (DC) components, as evident in the surface amplitude data and the resulting MT models. Furthermore, we found that source models that are constrained to be purely shear do not explain the data for most events. Thus, even though non-DC components of MTs can often be attributed to modeling artifacts, we argue that they are required by the data in some cases, and can be reliably computed and confidently interpreted under favorable conditions.

scholarly journals Time-Lapse Seismic Monitoring of Onshore Reservoirs in Niger Delta, Field ‘K’ as a Case Study

2017 ◽  
Vol 1 (1) ◽  
pp. 23-27 ◽  
Author(s):  
A. Ogbamikhumi ◽  
T. Tralagba ◽  
E. E. Osagiede
Keyword(s):  
Seismic Data ◽  
Acoustic Impedance ◽  
Niger Delta ◽  
Rock Physics ◽  
Time Lapse ◽  
Seismic Survey ◽  
Impedance Change ◽  
Data Set ◽  
Reservoir Fluid ◽  
4D Seismic

Field ‘K’ is a mature field in the coastal swamp onshore Niger delta, which has been producing since 1960. As a huge producing field with some potential for further sustainable production, field monitoring is therefore important in the identification of areas of unproduced hydrocarbon. This can be achieved by comparing production data with the corresponding changes in acoustic impedance observed in the maps generated from base survey (initial 3D seismic) and monitor seismic survey (4D seismic) across the field. This will enable the 4D seismic data set to be used for mapping reservoir details such as advancing water front and un-swept zones. The availability of good quality onshore time-lapse seismic data for Field ‘K’ acquired in 1987 and 2002 provided the opportunity to evaluate the effect of changes in reservoir fluid saturations on time-lapse amplitudes. Rock physics modelling and fluid substitution studies on well logs were carried out, and acoustic impedance change in the reservoir was estimated to be in the range of 0.25% to about 8%. Changes in reservoir fluid saturations were confirmed with time-lapse amplitudes within the crest area of the reservoir structure where reservoir porosity is 0.25%. In this paper, we demonstrated the use of repeat Seismic to delineate swept zones and areas hit with water override in a producing onshore reservoir.

Applications of quantitative prestack seismic analysis to unconventional resource play characterization in the Permian/Delaware Basin

2019 ◽  
Vol 38 (2) ◽  
pp. 106-115 ◽  
Author(s):  
Phuong Hoang ◽  
Arcangelo Sena ◽  
Benjamin Lascaud
Keyword(s):  
Hydraulic Fracturing ◽  
Seismic Data ◽  
Reservoir Characterization ◽  
Seismic Analysis ◽  
Seismic Inversion ◽  
Reservoir Properties ◽  
Yield Attributes ◽  
Horizontal Drilling ◽  
Delaware Basin ◽  
Unconventional Resource

The characterization of shale plays involves an understanding of tectonic history, geologic settings, reservoir properties, and the in-situ stresses of the potential producing zones in the subsurface. The associated hydrocarbons are generally recovered by horizontal drilling and hydraulic fracturing. Historically, seismic data have been used mainly for structural interpretation of the shale reservoirs. A primary benefit of surface seismic has been the ability to locate and avoid drilling into shallow carbonate karsting zones, salt structures, and basement-related major faults which adversely affect the ability to drill and complete the well effectively. More recent advances in prestack seismic data analysis yield attributes that appear to be correlated to formation lithology, rock strength, and stress fields. From these, we may infer preferential drilling locations or sweet spots. Knowledge and proper utilization of these attributes may prove valuable in the optimization of drilling and completion activities. In recent years, geophysical data have played an increasing role in supporting well planning, hydraulic fracturing, well stacking, and spacing. We have implemented an integrated workflow combining prestack seismic inversion and multiattribute analysis, microseismic data, well-log data, and geologic modeling to demonstrate key applications of quantitative seismic analysis utilized in developing ConocoPhillips' acreage in the Delaware Basin located in Texas. These applications range from reservoir characterization to well planning/execution, stacking/spacing optimization, and saltwater disposal. We show that multidisciplinary technology integration is the key for success in unconventional play exploration and development.

A skeptic's view of VVAz and AVAz

2020 ◽  
Vol 39 (2) ◽  
pp. 128-134 ◽  
Author(s):  
Norbert Van De Coevering ◽  
Klaas Koster ◽  
Rob Holt
Keyword(s):  
Phase Ii ◽  
Seismic Data ◽  
Wave Mode ◽  
P Wave ◽  
Noise Levels ◽  
Reservoir Properties ◽  
Data Set ◽  
Lower Amplitude ◽  
Software Note ◽  
Dense Sampling

We have applied a modern amplitude- and azimuth-preserving seismic data processing workflow to the SEG Advanced Modeling Program (SEAM) Phase II Barrett classic data set — an orthorhombic synthetic seismic model that has extremely dense sampling of all azimuths and offsets. We analyze the resulting prestack depth-migrated offset vector tiles with a variety of methods and software. Note that we only analyze the P-P wave mode, which is the focus of our study. We demonstrate that observed azimuthal changes cannot be correlated with the model's reservoir properties. We have made the migrated data available through SEAM. Compared to modeled data, real onshore seismic data have significantly lower amplitude fidelity, higher noise levels, and more uncertainty in the migration velocity field used for processing. Since we are unable to relate the anisotropy measured from the fully sampled clean SEAM Phase II Barrett synthetic seismic data to the model's known anisotropy, we conclude that it is highly unlikely that azimuthal variations observed on real onshore seismic data will be predictive of reservoir fracture properties.

Data-driven Prestack Waveform Inversion Using Genetic Algorithm- Methodology and Examples

2021 ◽  
pp. 1-97
Author(s):  
Lingxiao Jia ◽  
Subhashis Mallick ◽  
Cheng Wang
Keyword(s):  
Genetic Algorithm ◽  
Seismic Data ◽  
Waveform Inversion ◽  
Seismic Inversion ◽  
P Wave ◽  
Data Driven ◽  
Initial Model ◽  
Reservoir Properties ◽  
Well Control ◽  
Seismic Waveform

The choice of an initial model for seismic waveform inversion is important. In matured exploration areas with adequate well control, we can generate a suitable initial model using well information. However, in new areas where well control is sparse or unavailable, such an initial model is compromised and/or biased by the regions with more well controls. Even in matured exploration areas, if we use time-lapse seismic data to predict dynamic reservoir properties, an initial model, that we obtain from the existing preproduction wells could be incorrect. In this work, we outline a new methodology and workflow for a nonlinear prestack isotropic elastic waveform inversion. We call this method a data driven inversion, meaning that we derive the initial model entirely from the seismic data without using any well information. By assuming a locally horizonal stratification for every common midpoint and starting from the interval P-wave velocity, estimated entirely from seismic data, our method generates pseudo wells by running a two-pass one-dimensional isotropic elastic prestack waveform inversion that uses the reflectivity method for forward modeling and genetic algorithm for optimization. We then use the estimated pseudo wells to build the initial model for seismic inversion. By applying this methodology to real seismic data from two different geological settings, we demonstrate the usefulness of our method. We believe that our new method is potentially applicable for subsurface characterization in areas where well information is sparse or unavailable. Additional research is however necessary to improve the compute-efficiency of the methodology.

Sign in / Sign up

Export Citation Format

Share Document