Normalized base-flow discharge of groundwater basins: A useful parameter for estimating recharge area of springs and for recognizing drainage anomalies in karst terranes

2018 ◽  
pp. 149-164 ◽  
Author(s):  
James Equinlan ◽  
Joseph A. Ray
2019 ◽  
Vol 19 (1) ◽  
pp. 26-32
Author(s):  
Gilang Munggaran ◽  
Yayat Hidayat ◽  
Surya Darma Tarigan ◽  
Dwi Putro Tejo Baskoro

Cimanuk Watershed is a priority catchment in West Java Province. The objective of study is to analyze various land use scenarios to improve base flow and lateral flow. The analysis use SWAT Hydrology model. The study showed that model has a good performance in predicting flow discharge produced NSE 0.56 (satisfactorily) and R2 0.70. There are four scenarios to be analyzed. The best base flow and lateral flow analyses is from the first scenario with soil and water conservation techniques. The scenario resulted the river regime coefficient by 78 (moderat), reduce direct runoff by 40.76% and increase lateral by 536.95 mm. Keywords: Base flow, landuse, lateral flow, soil and water conservation techniques, SWAT model 


Soil Research ◽  
2011 ◽  
Vol 49 (4) ◽  
pp. 329 ◽  
Author(s):  
V. Rasiah ◽  
P. W. Moody ◽  
J. D. Armour

Soluble reactive phosphorus (SP) present in groundwater (GW) is generally considered insignificant, and therefore of little consequence to the quality of waters receiving base-flow discharges. In this study we investigated whether: (i) significant quantities of SP were present in GW (GW-SP); (ii) potential existed for GW-SP to be exported to streams via base-flow discharge; and (iii) the exports are a health risk to ecosystems receiving base-flow discharges. Investigations were carried out at two sites in the Tully River Catchment (TRC) during three consecutive rainy seasons, and 24 wells in the Johnstone River Catchment (JRC) were also monitored during one rainy season, in the north-eastern wet tropics of Australia. In the TRC, the GW-SP varied temporally, within and between rainy seasons, from 2 to 158 μg P/L at Site 1 and from 3 to 31 μg P/L at Site 2. The temporal variations in GW-SP were driven by fluctuating water-table at Site 2, but no such trend was observed at Site 1. The SP in drain-water (DW-SP) varied temporally from 0.6 to 110 μg P/L at Site 1, compared with 2–83 μg P/L at Site 2. The positive association between DW-SP and GW-SP at Site 2 indicated an export of SP from GW to a drain via base-flow discharge. In the JRC, the GW-SP in the 24 wells varied temporally from 0 to 300 μg P/L with the means across the wells ranging from 5 to 190 μg P/L, with the variations driven by fluctuating water-tables. More than 50% of the GW-SP or DW-SP concentrations in TRC were significantly higher than the P trigger values, 2–5 μg P/L, proposed to sustain the health of aquatic ecosystems in this region; a similar result was observed in the JRC. Speciation analysis via filtering (i.e. P passing through a 0.45-μm filter) for selected GW samples indicated substantial quantities of soluble organic P in some wells, ranging from 5 to 89% (mean 38%) of the total soluble P (SP plus soluble organic P). Because the soluble organic P was not included in GW-SP determinations, the hazard/risk mentioned above is an underestimate. The GW-SP exported during rainy seasons, from both catchments, ranged from 0.16 to 0.43 kg P/ha. Our findings indicate there were significant quantities of SP and soluble organic P in GW, it was exported to streams, and there is a health risk to receiving surface water bodies.


2017 ◽  
Vol 5 (4) ◽  
pp. 26-32 ◽  
Author(s):  
Azaria Robiana ◽  
M. Yashin Nahar ◽  
Hamidah Harahap

Glycerin residue is waste oleochemical industry that still contain glycerin. To produce quality and maximum quantity of glycerin, then research the effect of pH acidification using phosphoric acid. Glycerin analysis includes the analysis of pH, Fatty Acid and Ester (FAE), and analysis of the levels of glycerin. The maximum yield obtained at pH acidification 2 is grading 91,60% glycerin and Fatty Acid and Ester (FAE) 3,63 meq/100 g. Glycerin obtained is used as a plasticizer in the manufacture of bioplastics. Manufacture of bioplastics using the method of pouring a solution with varying concentrations of starch banana weevil (5% w/v and 7% w/v), variations of the addition of glycerin (1 ml, 3 ml, 5 ml and 7 ml), and a variety of gelatinization temperature (60°C, 70°C, and 80°C). Analysis of bioplastics include FTIR testing, tensile strength that is supported by SEM analysis. The results obtained in the analysis of FTIR does not form a new cluster on bioplastics starch banana weevil, but only a shift in the recharge area only, it is due to the addition of O-H groups originating from water molecules that enter the polysaccharide through a mechanism gelatinitation that generates interaction hydrogen bonding strengthened. The maximum tensile strength of bioplastics produced at a concentration of starch 7% w/v, 1 ml glycerine and gelatinization temperature of 80°C is 3,430 MPa. While the tensile strength bioplastic decreased with increasing glycerin which can be shown from the results of SEM where there is a crack, indentations and lumps of starch insoluble.


AIAA Journal ◽  
2002 ◽  
Vol 40 ◽  
pp. 2217-2224
Author(s):  
C. J. Bourdon ◽  
J. C. Dutton
Keyword(s):  

Sign in / Sign up

Export Citation Format

Share Document