Porosity and Microcrack Dependence of Fracture Energy and Toughness and Related Crack Propagation at 22°C

2017 ◽  
pp. 168-209
Author(s):  
Roy W. Rice
2014 ◽  
Vol 513-517 ◽  
pp. 20-23
Author(s):  
Hai Chao Wang ◽  
Xue Hua Wang ◽  
Xue Hui An

The different fracture characteristics of self-compacting rock-filled concrete with large-size natural and recycled aggregate are analyzed by three-point bending experiment. According to the analysis of the crack propagation process, the fracture mechanism differences of self-compacting rock-filled concrete with large-size natural and recycled aggregate are discussed. The further analysis of the differences of fracture toughness, fracture energy, and are gain


2013 ◽  
Vol 815 ◽  
pp. 233-239
Author(s):  
Xue Quan Liu ◽  
Cun Guang Ding ◽  
Chang Hai Li ◽  
Yi Li ◽  
Li Xin Li ◽  
...  

A fibrous monolith cemented carbide with WC-6Co as cell and WC-20Co as cell boundaries was produced through hot co-extrusion process in this paper. The density, hardness, bending strength and fracture toughness of the fibrous monolith cemented carbide were tested, and the fracture and crack propagation were observed by metalloscope and SEM. The results showed that the bending strength and fracture toughness of the fibrous monolith cemented carbides was remarkably improved 71.91% and 45.7% respectively, while the hardness was slightly decreased 1% compared with WC-6Co composites. It is the reason that the tougher shell WC-20Co with higher bending strength and fracture toughness can absorb more fracture energy, which can slow down and prevent the crack propagating from brittle core WC-6Co.


Holzforschung ◽  
2001 ◽  
Vol 55 (5) ◽  
pp. 525-533 ◽  
Author(s):  
E.K. Tschegg ◽  
K. Frühmann ◽  
S.E. Stanzl-Tschegg

Summary Tests under mode I and mode III loading were performed on side grooved Compact-Tension specimens of larch and beech under steady state crack propagation to study the damage and fracture behaviour and the influence of two fibre orientations. From the complete load-displacement diagram, all important damage and fracture mechanical values (stiffness/compliance, microstructural damage, crack initiation energy, specific fracture energy, etc.) have been determined. Crack initiation energy and specific fracture energy are approximately ten times higher for mode III loading than for mode I loading in both wood species. Crack initiation occurs in mode III under external mode III loading, crack propagation, however, takes place under mode I, owing to crack surface interference. The influence of fibre orientation on the (fracture) mechanical properties of beech and larch is different. This difference may be explained mainly by the high number of rays in beech.


2021 ◽  
Author(s):  
Bastian Bergfeld ◽  
Alec van Herwijnen ◽  
Benjamin Reuter ◽  
Grégoire Bobillier ◽  
Jürg Dual ◽  
...  

Abstract. To assess snow avalanche release probability, information on failure initiation and crack propagation in weak snowpack layers underlying cohesive slab layers are required. With the introduction of the Propagation Saw Test (PST) in the mid-2000s, various studies used particle tracking analysis of high-speed video recordings of PST experiments to gain insight into crack propagation processes, including slab bending, weak layer collapse, crack propagation speed and the frictional behavior after weak layer fracture. However, the resolution of the videos and the methodology used did not allow insight into dynamic processes such as the evolution of crack speed within a PST or the touchdown distance, which is the length from the crack tip to the trailing point where the slab sits on the crushed weak layer at rest again. Therefore, to study the dynamics of crack propagation we recorded PST experiments using a powerful portable high-speed camera with a horizontal resolution of 1280 pixels at rates up to 20,000 frames per second. By applying a high-density speckling pattern on the entire PST column, we then used digital image correlation (DIC) to derive high-resolution displacement and strain fields in the slab, weak layer, and substrate. The high frame rates allowed time derivatives to obtain velocity and acceleration fields. On the one hand, we demonstrate the versatile capabilities and accuracy of the DIC method by showing three PST experiments resulting in slab fracture, crack arrest and full propagation. On the other hand, we present a methodology to determine relevant characteristics of crack propagation: the crack speed and touchdown distance within a PST, and the specific fracture energy of the weak layer. To estimate the effective elastic modulus of the slab and weak layer as well as the weak layer specific fracture energy we used a recently proposed mechanical model. A comparison to already established methods showed good agreement. Furthermore, our methodology also provides insight into the three different propagation results found with the PST and reveals intricate dynamics that are otherwise not accessible.


Author(s):  
Jae Beom Park ◽  
Tapan Sabuwala ◽  
Gustavo Gioia

It has been inferred from computer simulations that the plastic-zone fields of a crack that propagates steadily under K–T loading are similarity fields. Here, we show theoretically that these similarity fields are but a manifestation of the existence of an invariant path integral. We also show that the attendant similarity variable involves an intrinsic length scale set by the specific fracture energy that flows into the crack tip. Finally, we show that where the crack is stationary there can be no similarity fields, even though there exists a (different) invariant path integral. Our results afford some new insights into the relation between similarity fields and invariant path integrals in mathematical physics.


Sign in / Sign up

Export Citation Format

Share Document