Monitoring Soil Moisture Deficit Using SMOS Satellite Soil Moisture: Correspondence through Rainfall-runoff Model

2020 ◽  
Author(s):  
Martin Kubáň ◽  
Patrik Sleziak ◽  
Adam Brziak ◽  
Kamila Hlavčová ◽  
Ján Szolgay

<p>A multi-objective calibration of the parameters of conceptual hydrologic models has the potential to improve the consistency of the simulated model states, their representativeness with respect to catchment states and thereby to reduce the uncertainty in the estimation of hydrological model outputs. Observed in-situ or remotely sensed state variables, such as the snow cover distribution, snow depth, snow water equivalent and soil moisture were often considered as additional information in such calibration strategies and subsequently utilized in data assimilation for operational streamflow forecasting. The objective of this paper is to assess the effects of the inclusion of MODIS products characterizing soil moisture and the snow water equivalent in a multi-objective calibration strategy of an HBV type conceptual hydrological model under the highly variable physiographic conditions over the whole territory of Austria.</p><p>The methodology was tested using the Technical University of Vienna semi-distributed rainfall-runoff model (the TUW model), which was calibrated and validated in 213 Austrian catchments. For calibration we use measured data from the period 2005 to 2014. Subsequently, we simulated discharges, soil moisture and snow water equivalents based on parameters from the multi-objective calibration and compared these with the respective MODIS values. In general, the multi-objective calibration improved model performance when compared to results of model parametrisation calibrated only on discharge time series. Sensitivity analyses indicate that the magnitude of the model efficiency is regionally sensitive to the choice of the additional calibration variables. In the analysis of the results we indicate ranges how and where the runoff, soil moisture and snow water equivalent simulation efficiencies were sensitive to different setups of the multi-objective calibration strategy over the whole territory of Austria. It was attempted to regionalize the potential to increase of the overall model performance and the improvement in the consistency of the simulation of the two-state variables. Such regionalization may serve model users in the selection which remotely sensed variable or their combination is to be preferred in local modelling studies.</p>


2021 ◽  
Author(s):  
Nutchanart Sriwongsitanon ◽  
Wasana Jandang ◽  
Thienchart Suwawong ◽  
Hubert H. G. Savenije

Abstract. A parsimonious semi-distributed rainfall-runoff model has been developed for flow prediction. In distribution, attention is paid to both timing of runoff and heterogeneity of moisture storage capacities within sub-catchments. This model is based on the lumped FLEXL model structure, which has proven its value in a wide range of catchments. To test the value of distribution, the gauged Upper Ping catchment in Thailand has been divided into 32 sub-catchments, which can be grouped into 5 gauged sub-catchments where internal performance is evaluated. To test the effect of timing, firstly excess rainfall was calculated for each sub-catchment, using the model structure of FLEXL. The excess rainfall was then routed to its outlet using the lag time from storm to peak flow (TlagF) and the lag time of recharge from the root zone to the groundwater (TlagS), as a function of catchment size. Subsequently, the Muskingum equation was used to route sub-catchment runoff to the downstream sub-catchment, with the delay time parameter of the Muskingum equation being a function of channel length. Other model parameters of this semi-distributed FLEX-SD model were kept the same as in the calibrated FLEXL model of the entire Upper Ping basin, controlled by station P.1 located at the centre of Chiang Mai Province. The outcome of FLEX-SD was compared to: 1) observations at the internal stations; 2) the calibrated FLEXL model; and 3) the semi-distributed URBS model - another established semi-distributed rainfall-runoff model. FLEX-SD showed better or similar performance both during calibration and especially in validation. Subsequently, we tried to distribute the moisture storage capacity by constraining FLEX-SD on patterns of the NDII (normalized difference infrared index). The readily available NDII appears to be a good proxy for moisture stress in the root zone during dry periods. The maximum moisture holding capacity in the root zone is assumed to be a function of the maximum seasonal range of NDII values, and the annual average NDII values to construct 2 alternative models: FLEX-SD-NDIIMax-Min and FLEX-SD-NDIIAvg, respectively. The additional constraint on the moisture holding capacity by the NDII improved both model performance and the realism of the distribution. Distribution of Sumax using annual average NDII values was found to be well correlated with the percentage of evergreen forest in 31 sub-catchments. Spatial average NDII values were proved to be highly corresponded with the root zone soil moisture of the river basin, not only in the dry season but also in the water limited ecosystem. To check how well the model represents root zone soil moisture, the performance of the FLEX-SD-NDII model was compared to time series of the soil wetness index (SWI). The correlation between the root zone storage and the daily SWI appeared to be very good, even better than the correlation with the NDII, because NDII does not provide good estimates during wet periods. The SWI, which is partly model-based, was not used for calibration, but appeared to be an appropriate index for validation.


2003 ◽  
Vol 34 (3) ◽  
pp. 161-178
Author(s):  
H. Sun ◽  
P. S. Cornish ◽  
T. M. Daniell

A rainfall runoff model based on a digital elevation model (DEM) was applied to a small catchment in Happy Valley, South Australia to predict catchment storm runoff. The DEM was used to partition the catchment into several thousand irregular shaped elements. These elements, with an average size of 825 m2 each, form an interconnected one-dimensional flow network for runoff routing. The rainfall runoff model is a kinematic flow model which combines the solving of flow continuity equation and the Manning's equation to generate surface and subsurface runoff. This study improves on the existing rainfall runoff model in several areas. It adds spatial rainfall averaging methods to derive spatial rainfalls for catchment modelling; and it improves the catchment soil moisture representation by developing a boundary wetness index, and relates this index to antecedent catchment flow to derive spatial catchment moisture distribution. Improved runoff predictions were obtained as a result of the improvement in spatial data input and spatial soil moisture representation. The study identifies these improvements as the key areas for better runoff prediction. It demonstrates that where prediction results showed larger than expected variance, it is frequently caused by the inability to derive good spatially distributed input data rather than parameter estimation errors.


Sign in / Sign up

Export Citation Format

Share Document