Theoretical and experimental stress analyses of centrifugal fan impellers

1978 ◽  
Vol 13 (3) ◽  
pp. 141-147 ◽  
Author(s):  
R Bell ◽  
P P Benham
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Strain Gauge ◽  
Simplified Model ◽  
Centrifugal Fan ◽  
Experimental Stress ◽  
Stress Distributions ◽  
Element Analysis ◽  
Stress Analyses

Brittle-lacquer and strain-gauge methods and a finite-element analysis are used to determine stress distributions in a simplified model and an actual centrifugal fan impeller.

scholarly journals Comparison of Tooth- and Bone-Borne Appliances on the Stress Distributions and Displacement Patterns in the Facial Skeleton in Surgically Assisted Rapid Maxillary Expansion—A Finite Element Analysis (FEA) Study

Materials ◽  
2021 ◽  
Vol 14 (5) ◽  
pp. 1152
Author(s):  
Rafał Nowak ◽  
Anna Olejnik ◽  
Hanna Gerber ◽  
Roman Frątczak ◽  
Ewa Zawiślak
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Three Dimensional ◽  
Element Model ◽  
Rapid Maxillary Expansion ◽  
Stress Distributions ◽  
Maxillary Expansion ◽  
Facial Skeleton ◽  
Element Analysis ◽  
Maxillary Constriction

The aim of this study was to compare the reduced stresses according to Huber’s hypothesis and the displacement pattern in the region of the facial skeleton using a tooth- or bone-borne appliance in surgically assisted rapid maxillary expansion (SARME). In the current literature, the lack of updated reports about biomechanical effects in bone-borne appliances used in SARME is noticeable. Finite element analysis (FEA) was used for this study. Six facial skeleton models were created, five with various variants of osteotomy and one without osteotomy. Two different appliances for maxillary expansion were used for each model. The three-dimensional (3D) model of the facial skeleton was created on the basis of spiral computed tomography (CT) scans of a 32-year-old patient with maxillary constriction. The finite element model was built using ANSYS 15.0 software, in which the computations were carried out. Stress distributions and displacement values along the 3D axes were found for each osteotomy variant with the expansion of the tooth- and the bone-borne devices at a level of 0.5 mm. The investigation showed that in the case of a full osteotomy of the maxilla, as described by Bell and Epker in 1976, the method of fixing the appliance for maxillary expansion had no impact on the distribution of the reduced stresses according to Huber’s hypothesis in the facial skeleton. In the case of the bone-borne appliance, the load on the teeth, which may lead to periodontal and orthodontic complications, was eliminated. In the case of a full osteotomy of the maxilla, displacements in the buccolingual direction for all the variables of the bone-borne appliance were slightly bigger than for the tooth-borne appliance.

Structural Analysis of Centrifugal Fan Impeller Using CATIA Software

2015 ◽  
Vol 809-810 ◽  
pp. 859-864
Author(s):  
Dănuţ Zahariea
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Structural Analysis ◽  
Design Methods ◽  
Constant Thickness ◽  
Blade Design ◽  
Centrifugal Fan ◽  
Element Analysis ◽  
The Finite Element Analysis ◽  
Modes Of Vibration

In this paper, the finite element analysis for stress/deformation/modes of vibration for the centrifugal fan impeller with constant thickness backward-curved blades using CATIA software will be presented. The principal steps of the finite element analysis procedure using CATIA/Generative Structural Analysis environment will be presented: creating the 3D model; configuring the mesh; applying the restraints; applying the loads; running the numerical static analysis and the numerical frequency analysis; interpreting the results and observing the modes of vibration correlating with the impeller mode shape. This procedure will be used for 4 different centrifugal fan impellers according with the 4 blade design methods and the results will be comparatively analyzed. For each design method, two materials will be used: steel with density of 7860 kg/m3 and aluminium with density of 2710 kg/m3. Two important results have been obtained after the structural analysis: under the working conditions considered for the analysis, all 4 blade design methods leads to impellers with very good mechanical behaviour; any frequency of the main modes of vibrations for all blade design methods and for both materials is not in phase with the impeller speed, thus the possibility of resonance being eliminated.

Application of ESPI in the Vibration Analysis of Turbine Blading

1995 ◽  
Author(s):  
Robert X. Wang ◽  
Graham M. Chapman
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Vibration Analysis ◽  
Speckle Pattern ◽  
Vibration Measurement ◽  
Simplified Model ◽  
Electronic Speckle Pattern Interferometry ◽  
Coupled Modes ◽  
Element Analysis ◽  
Turbine Blading

Abstract This paper reports on the application of Electronic Speckle Pattern Interferometry (ESPI) technique in vibration measurement of turbine blading. Using the time-averaged mode of ESPI, the first six modes of a turbocharger blade with airfoil profile were identified. The effect of the complicated profile of the blade was established by studying simplified model blades. Coupled modes were identified and successfully separated. Experimental results are compared with those obtained using finite element analysis.

Investigation on stress distribution and pressure capacity of two-layer split high-pressure die based on finite element analysis

2019 ◽  
Vol 233 (14) ◽  
pp. 5048-5055
Author(s):  
Z Yi ◽  
WZ Fu ◽  
MZ Li
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
High Pressure ◽  
Stress State ◽  
Von Mises Stress ◽  
Stress Distributions ◽  
Element Analysis ◽  
Round Cylinder ◽  
Von Mises ◽  
Supporting Ring

In order to obtain a higher pressure capacity for the high-pressure die with a larger sample cavity, two types of two-layer split dies with a round cylinder and a quadrate cylinder were designed based on the conventional belt-type die. Finite element analysis was performed to investigate the stress distributions and pressure capacities of the high-pressure dies using a derived Mohr–Coulomb criterion and the von Mises criterion for the cylinder and supporting rings, respectively. As predicted by the finite element analysis results, in the two-layer split dies with a round cylinder, the stress state of the cylinder can be only slightly improved; and the von Mises stress of the first layer supporting ring can be hardly decreased. However, in the two-layer split dies with a quadrate cylinder and sample cavity, the stress state of the cylinder can be remarkably improved. Simultaneously, the von Mises stress of the supporting rings, especially for the first-layer supporting ring, can be also effectively decreased. The pressure capacities of the two-layer split dies with a round cylinder and a quadrate cylinder are 16.5% and 63.9% higher with respect to the conventional belt-type die.

Finite Element Analysis of Composite Volleyball Upright Structures

2012 ◽  
Vol 446-449 ◽  
pp. 247-250
Author(s):  
Lu Yang Shan ◽  
Yi Shan
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Static Analysis ◽  
Upper Bound ◽  
Stress Distributions ◽  
Dynamic Impact ◽  
Fe Method ◽  
Element Analysis ◽  
Impact Effect ◽  
Finite Element Software

A composite FRP volleyball upright structure is analyzed by finite element (FE) method. A static analysis is performed using commercial finite element software ANSYS. Deformation and stress distributions under regular and upper bound force (i.e., to include dynamic/impact effect) are provided. An elastic eigenvalue analysis is carried out as well to predict the buckling load and modes.

Sign in / Sign up

Export Citation Format

Share Document