Development of Three-Dimensional Simulation Code for Two-Phase Flow in a Steam Generator

2020 ◽  
Vol 2020.95 (0) ◽  
pp. 07_703
Author(s):  
Yoshiyuki KONDO ◽  
Koichi TANIMOTO ◽  
Ling CHENG ◽  
Yoshiteru KOMURO ◽  
Atsushi KODAMA ◽  
...  
Keyword(s):  
Steam Generator ◽  
Two Phase Flow ◽  
Three Dimensional ◽  
Phase Flow ◽  
Two Phase ◽  
Simulation Code ◽  
Dimensional Simulation

Time Domain Simulation of the Vibration of a Steam Generator Tube Subjected to Fluidelastic Forces Induced by Two-Phase Cross-Flow

2013 ◽  
Vol 135 (3) ◽  
Author(s):  
Téguewindé Sawadogo ◽  
Njuki Mureithi
Keyword(s):  
Steam Generator ◽  
Two Phase Flow ◽  
Work Rate ◽  
Fretting Wear ◽  
Phase Flow ◽  
Reference Case ◽  
Two Phase ◽  
Steam Generator Tube ◽  
Wide Range ◽  
Instability Regime

Having previously verified the quasi-steady model under two-phase flow laboratory conditions, the present work investigates the feasibility of practical application of the model to a prototypical steam generator (SG) tube subjected to a nonuniform two-phase flow. The SG tube vibration response and normal work-rate induced by tube-support interaction are computed for a range of flow conditions. Similar computations are performed using the Connors model as a reference case. In the quasi-steady model, the fluid forces are expressed in terms of the quasi-static drag and lift force coefficients and their derivatives. These forces have been measured in two-phase flow over a wide range of void fractions making it possible to model the effect of void fraction variation along the tube span. A full steam generator tube subjected to a nonuniform two-phase flow was considered in the simulations. The nonuniform flow distribution corresponds to that along a prototypical steam-generator tube based on thermal-hydraulic computations. Computation results show significant and important differences between the Connors model and the two-phase flow based quasi-steady model. While both models predict the occurrence of fluidelastic instability, the predicted pre-instability and post instability behavior is very different in the two models. The Connors model underestimates the flow-induced negative damping in the pre-instability regime and vastly overestimates it in the post instability velocity range. As a result the Connors model is found to underestimate the work-rate used in the fretting wear assessment at normal operating velocities, rendering the model potentially nonconservative under these practically important conditions. Above the critical velocity, this model largely overestimates the work-rate. The quasi-steady model on the other hand predicts a more moderately increasing work-rate with the flow velocity. The work-rates predicted by the model are found to be within the range of experimental results, giving further confidence to the predictive ability of the model. Finally, the two-phase flow based quasi-steady model shows that fluidelastic forces may reduce the effective tube damping in the pre-instability regime, leading to higher than expected work-rates at prototypical operating velocities.

scholarly journals Research Method and Two-Phase Flow Stability of the Steam Generator of HTR-10

2001 ◽  
Vol 38 (9) ◽  
pp. 739-744 ◽  
Author(s):  
Huaiming JU ◽  
Yuanhui XU ◽  
Zhiyong HUANG ◽  
Yu YU
Keyword(s):  
Steam Generator ◽  
Research Method ◽  
Two Phase Flow ◽  
Flow Stability ◽  
Phase Flow ◽  
Two Phase

A Combined Eulerian and Lagrangian Method for Prediction of Evaporating Sprays

2002 ◽  
Vol 124 (3) ◽  
pp. 481-488 ◽  
Author(s):  
M. Burger ◽  
G. Klose ◽  
G. Rottenkolber ◽  
R. Schmehl ◽  
D. Giebert ◽  
...  
Keyword(s):  
Two Phase Flow ◽  
Initial Conditions ◽  
Three Dimensional ◽  
Lagrangian Method ◽  
Phase Flow ◽  
Two Phase Flows ◽  
Two Phase ◽  
Lagrangian Methods ◽  
Eulerian Method ◽  
Lagrangian Modeling

Polydisperse sprays in complex three-dimensional flow systems are important in many technical applications. Numerical descriptions of sprays are used to achieve a fast and accurate prediction of complex two-phase flows. The Eulerian and Lagrangian methods are two essentially different approaches for the modeling of disperse two-phase flows. Both methods have been implemented into the same computational fluid dynamics package which is based on a three-dimensional body-fitted finite volume method. Considering sprays represented by a small number of droplet starting conditions, the Eulerian method is clearly superior in terms of computational efficiency. However, with respect to complex polydisperse sprays, the Lagrangian technique gives a higher accuracy. In addition, Lagrangian modeling of secondary effects such as spray-wall interaction enhances the physical description of the two-phase flow. Therefore, in the present approach the Eulerian and the Lagrangian methods have been combined in a hybrid method. The Eulerian method is used to determine a preliminary solution of the two-phase flow field. Subsequently, the Lagrangian method is employed to improve the accuracy of the first solution using detailed sets of initial conditions. Consequently, this combined approach improves the overall convergence behavior of the simulation. In the final section, the advantages of each method are discussed when predicting an evaporating spray in an intake manifold of an internal combustion engine.

scholarly journals Numerical Simulation and Analysis on Spray Drift Movement of Multirotor Plant Protection Unmanned Aerial Vehicle

Energies ◽  
2018 ◽  
Vol 11 (9) ◽  
pp. 2399 ◽  
Author(s):  
Fengbo Yang ◽  
Xinyu Xue ◽  
Chen Cai ◽  
Zhu Sun ◽  
Qingqing Zhou
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
Droplet Size ◽  
Wind Field ◽  
Flow Model ◽  
Two Phase Flow ◽  
Plant Protection ◽  
Three Dimensional ◽  
Phase Flow ◽  
Two Phase

In recent years, multirotor unmanned aerial vehicles (UAVs) have become more and more important in the field of plant protection in China. Multirotor unmanned plant protection UAVs have been widely used in vast plains, hills, mountains, and other regions, and become an integral part of China’s agricultural mechanization and modernization. The easy takeoff and landing performances of UAVs are urgently required for timely and effective spraying, especially in dispersed plots and hilly mountains. However, the unclearness of wind field distribution leads to more serious droplet drift problems. The drift and distribution of droplets, which depend on airflow distribution characteristics of UAVs and the droplet size of the nozzle, are directly related to the control effect of pesticide and crop growth in different growth periods. This paper proposes an approach to research the influence of the downwash and windward airflow on the motion distribution of droplet group for the SLK-5 six-rotor plant protection UAV. At first, based on the Navier-Stokes (N-S) equation and SST k–ε turbulence model, the three-dimensional wind field numerical model is established for a six-rotor plant protection UAV under 3 kg load condition. Droplet discrete phase is added to N-S equation, the momentum and energy equations are also corrected for continuous phase to establish a two-phase flow model, and a three-dimensional two-phase flow model is finally established for the six-rotor plant protection UAV. By comparing with the experiment, this paper verifies the feasibility and accuracy of a computational fluid dynamics (CFD) method in the calculation of wind field and spraying two-phase flow field. Analyses are carried out through the combination of computational fluid dynamics and radial basis neural network, and this paper, finally, discusses the influence of windward airflow and droplet size on the movement of droplet groups.

Two-Phase Flow Field Numerical Simulation in Scrubber for Exhaust Gas Desulfurization

2014 ◽  
Vol 541-542 ◽  
pp. 1288-1291
Author(s):  
Zhi Feng Dong ◽  
Quan Jin Kuang ◽  
Yong Zheng Gu ◽  
Rong Yao ◽  
Hong Wei Wang
Keyword(s):  
Numerical Simulation ◽  
Flow Field ◽  
Flue Gas ◽  
Two Phase Flow ◽  
Three Dimensional ◽  
Flue Gas Desulfurization ◽  
Parameter Design ◽  
Phase Flow ◽  
Two Phase ◽  
Entrance Angle

Calculation fluid dynamics software Fluent was used to conduct three-dimensional numerical simulation on gas-liquid two-phase flow field in a wet flue gas desulfurization scrubber. The k-ε model and SIMPLE computing were adopted in the analysis. The numerical simulation results show that the different gas entrance angles lead to internal changes of gas-liquid two-phase flow field, which provides references for reasonable parameter design of entrance angle in the scrubber.

Sign in / Sign up

Export Citation Format

Share Document