F221 Measurement of liquid velocity in gas-liquid two-phase flow in a 2x2 rod bundle

2014 ◽  
Vol 2014.19 (0) ◽  
pp. 369-370
Author(s):  
Yuma OGAWA ◽  
Shigeo HOSOKAWA ◽  
Akio TOMIYAMA
2018 ◽  
Vol 115 ◽  
pp. 480-486 ◽  
Author(s):  
Bin Yu ◽  
Wenxiong Zhou ◽  
Liangming Pan ◽  
Hang Liu ◽  
Quanyao Ren ◽  
...  

2018 ◽  
Vol 72 ◽  
pp. 257-273 ◽  
Author(s):  
Hang Liu ◽  
Liang-ming Pan ◽  
Takashi Hibiki ◽  
Wen-xiong Zhou ◽  
Quan-yao Ren ◽  
...  

2021 ◽  
pp. 1-13
Author(s):  
Ghassan H. Abdul-Majeed ◽  
Abderraouf Arabi ◽  
Gabriel Soto-Cortes

Summary Most of the existing slug (SL) to churn (CH) or SL to pseudo-slug (PS) transition models (empirical and mechanistic) account for the effect of the SL liquid holdup (HLS). For simplicity, some of these models assume a constant value of HLS in SL/CH and SL/PS flow transitions, leading to a straightforward solution. Other models correlate HLS with different flow variables, resulting in an iterative solution for predicting these transitions. Using an experimental database collected from the open literature, two empirical correlations for prediction HLS at the SL/PS and SL/CH transitions (HLST) are proposed in this study. This database is composed of 1,029 data points collected in vertical, inclined, and horizontal configurations. The first correlation is developed for medium to high liquid viscosity two-phase flow (μL > 0.01 Pa·s), whereas the second one is developed for low liquid viscosity flow (μL ≤ 0.01 Pa·s). Both correlations are shown to be a function of superficial liquid velocity (VSL), liquid viscosity (μL), and pipe inclination angle (θ). The proposed correlations in a combination with the HLS model of Abdul-Majeed and Al-Mashat (2019) have been used to predict SL/PS and SL/CH transitions, and very satisfactory results were obtained. Furthermore, the SL/CH model of Brauner and Barnea (1986) is modified by using the proposed HLST correlations, instead of using a constant value. The modification results in a significant improvement in the prediction of SL/CH and SL/PS transitions and fixes the incorrect decrease of superficial gas velocity (VSG) with increasing VSL. The modified model follows the expected increase of VSG for high VSL, shown by the published observations. The proposed combinations are compared with the existing transition models and show superior performance among all models when tested against 357 measured data from independent studies.


2019 ◽  
Vol 109 ◽  
pp. 109881 ◽  
Author(s):  
Miao Gui ◽  
Zhaohui Liu ◽  
Bo Liao ◽  
Teng Wang ◽  
Yong Wang ◽  
...  

Author(s):  
Xu Han ◽  
Xiuzhong Shen ◽  
Toshihiro Yamamoto ◽  
Ken Nakajima ◽  
Takashi Hibiki

2011 ◽  
Vol 133 (9) ◽  
Author(s):  
Sidharth Paranjape ◽  
Shao-Wen Chen ◽  
Takashi Hibiki ◽  
Mamoru Ishii

Flow regime maps were obtained for adiabatic air-water two-phase flow through a flow channel with 8 × 8 rod bundle, which simulated a typical rod bundle in a boiling water reactor. Impedance void meters were used to measure the area averaged void fraction at various axial locations in the flow channel. The Cumulative Probability Distribution Functions of the signals from the impedance meters were utilized along with self organizing neural network methodology to identify the flow regimes. The flow regimes were identified at five axial locations in the channel in order to understand the development of the flow regimes in axial direction. The experimental flow regime transition boundaries for bubbly to cap-bubbly and part of the cap-turbulent to churn-turbulent agreed with the theoretical boundaries of bubbly to slug and slug to churn-turbulent in round pipes. In addition, the two impedance void meters located across a spacer grid, revealed the nature of change in the flow regime across the spacer grid.


Author(s):  
S. Dhanasekaran ◽  
T. Karunanithi

This investigation reports the experimental and theoretical results carried out to evaluate the axial dispersion number for an air-water system in a novel hybrid rotating and reciprocating perforated plate bubble column for single phase and two phase flow conditions. Axial dispersion studies are carried out using stimulus response technique. Sodium hydroxide solution is used as the tracer. Effects of superficial liquid velocity, agitation level and superficial gas velocity on axial dispersion number were analyzed and found to be significant. For the single phase (water) flow condition, it is found that the main variables affecting the axial dispersion number are the agitation level and superficial liquid velocity. When compared to the agitation level, the effect of superficial liquid velocity on axial dispersion number is more predominant. The increase in superficial liquid velocity decreases the axial dispersion number. The same trend is shown by agitation level but the effect is less. The rotational movement of the perforated plates enhances the radial mixing in the section; hence, axial dispersion number is reduced. For the two phase flow condition, the increase in superficial liquid velocity decreases the axial dispersion number, as reported in the single phase flow condition. The increase in agitation level decreases the axial dispersion number, but this decreasing trend is non-linear. An increase in superficial gas velocity increases the axial dispersion number. Correlations have been developed for axial dispersion number for single phase and two phase flow conditions. The correlation values are found to concur with the experimental values.


2012 ◽  
Vol 40 ◽  
pp. 166-177 ◽  
Author(s):  
Shao-Wen Chen ◽  
Yang Liu ◽  
Takashi Hibiki ◽  
Mamoru Ishii ◽  
Yoshitaka Yoshida ◽  
...  

Author(s):  
Yun Whan Na ◽  
J. N. Chung

Forced convective flow boiling in a single microchannel with different channel heights was studied through a numerical simulation method to investigate bubble dynamics, two-phase flow patterns, and boiling heat transfer. The momentum and energy equations were solved using a finite volume (FV) numerical method, while the liquid–vapor interface of a bubble is captured using the volume of fluid (VOF) technique. The effects of different constant wall heat fluxes and different channel heights on the boiling mechanisms were investigated. The effects of liquid velocity on the bubble departure diameter were also analyzed. The predicted bubble shapes and distribution profiles together with two-phase flow patterns are also provided.


2020 ◽  
Vol 368 ◽  
pp. 110815
Author(s):  
Yue Jin ◽  
Fan-Bill Cheung ◽  
Koroush Shirvan ◽  
Stephen M. Bajorek ◽  
Kirk Tien ◽  
...  

Sign in / Sign up

Export Citation Format

Share Document