C207 Local Heat Transfer Characteristics of Impinging Two-dimensional Hot Air Jet

2001 ◽  
Vol 2001 (0) ◽  
pp. 439-440
Author(s):  
Yuji SASABE ◽  
Nobuya NISHIMURA ◽  
Tomohiro NOMURA ◽  
Hiroyuki IYOTA
Keyword(s):  
Heat Transfer ◽  
Local Heat Transfer ◽  
Local Heat ◽  
Two Dimensional ◽  
Heat Transfer Characteristics ◽  
Transfer Characteristics ◽  
Hot Air ◽  
Air Jet

Local Heat Transfer Characteristics in Simulated Electronic Modules

2003 ◽  
Vol 125 (3) ◽  
pp. 362-368 ◽  
Author(s):  
Seong-Yeon Yoo ◽  
Jong-Hark Park ◽  
Min-Ho Chung
Keyword(s):  
Heat Transfer ◽  
Mass Transfer ◽  
Three Dimensional ◽  
Vortex Generator ◽  
Local Heat Transfer ◽  
Local Heat ◽  
Two Dimensional ◽  
Heat Transfer Characteristics ◽  
Dimensional Array ◽  
Transfer Characteristics

When heat is released by forced convection from electronic modules in a narrow printed circuit board channel, complex flow phenomena—such as stagnation and acceleration on the front surface, separation and reattachment on the top surface, wake or cavity flow near the rear surface—affect the heat transfer characteristics. The purpose of this study is to investigate how these flow conditions influence the local heat transfer from electronic modules. Experiments are performed on a three-dimensional array of hexahedral elements as well as on a two-dimensional array of rectangular elements. Naphthalene sublimation technique is employed to measure three-dimensional local mass transfer, and the mass transfer data are converted to their counterparts of the heat transfer process using the analogy equation between heat and mass transfer. Module location and streamwise module spacing are varied, and the effect of vortex generators on heat transfer enhancement is also examined. Dramatic change of local heat transfer coefficients is found on each surface of the module, and three-dimensional modules have a little higher heat transfer value than two-dimensional modules because of bypass flow. Longitudinal vortices formed by vortex generator enhance the mixing of fluids and thereby heat transfer, and the rectangular wing type vortex generator is found to be more effective than the delta wing type vortex generator.

scholarly journals 621 Heat Transfer Characteristics of Non-isothermal Two-dimensional Impinging Hot Air Jet with Multiple Nozzles

2001 ◽  
Vol 2001.76 (0) ◽  
pp. _6-39_-_6-40_
Author(s):  
Satoshi HABU ◽  
Nobuya NISHIMURA ◽  
Tomohiro NOMURA ◽  
Hiroyuki IYOTA
Keyword(s):  
Heat Transfer ◽  
Two Dimensional ◽  
Heat Transfer Characteristics ◽  
Transfer Characteristics ◽  
Hot Air ◽  
Air Jet

Numerical Research on Heat Transfer Characteristics Analysis of Two Particles in Supercritical Water

2021 ◽  
Author(s):  
Xiaoyu Li ◽  
Zhenqun Wu ◽  
Huibo Wang ◽  
Hui Jin
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Rate ◽  
Transfer Rate ◽  
Local Heat Transfer ◽  
Local Heat ◽  
Phase Flow ◽  
Heat Transfer Characteristics ◽  
Particle Cluster ◽  
Two Phase ◽  
Transfer Characteristics

Abstract In the supercritical water (SCW)-particle two-phase flow of fluidized bed, the particles that make up the particle cluster interact with each other through fluid, and it will affect the flow and heat transfer. However, due to the complex properties of SCW, the research on particle cluster is lacking, especially in terms of heat transfer. This research takes two particles as an example to study the heat transfer characteristics between SCW and another particle when one particle exists. This research uses the distance and angle between the two particles as the influencing factors to study the average heat transfer rate and local heat transfer rate. In this research, it is found that the effect is obvious when L/D = 1.1. When L = 1.1D, the temperature field and the flow field will partially overlap. The overlap of the temperature field will weaken the heat transfer between SCW and the particle. The overlap of the flow field has an enhanced effect on the heat transfer between SCW and the particle. The heat transfer between SCW and particles is simultaneously affected by these two effects, especially local heat transfer rate. In addition, this research also found that as the SCW temperature decreases, the thermal conductivity and specific heat of SCW increases, which enhances the heat transfer between SCW and the particles. This research is of great significance for studying the heat transfer characteristics of SCW-particle two-phase flow in fluidized bed.

Heat Transfer Characteristics of an Inclined Impinging Jet on a Curved Surface in Crossflow

2014 ◽  
Vol 136 (8) ◽  
Author(s):  
X. L. Wang ◽  
H. B. Yan ◽  
T. J. Lu ◽  
S. J. Song ◽  
T. Kim
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Flat Plate ◽  
Local Heat Transfer ◽  
Impinging Jet ◽  
Local Heat ◽  
Curved Surface ◽  
Heat Transfer Characteristics ◽  
Potential Core ◽  
Transfer Characteristics

This study reports on heat transfer characteristics on a curved surface subject to an inclined circular impinging jet whose impinging angle varies from a normal position θ = 0 deg to θ = 45 deg at a fixed jet Reynolds number of Rej = 20,000. Three curved surfaces having a diameter ratio (D/Dj) of 5.0, 10.0, and infinity (i.e., a flat plate) were selected, each positioned systematically inside and outside the potential core of jet flow where Dj is the circular jet diameter. Present results clarify similar and dissimilar local heat transfer characteristics on a target surface due to the convexity. The role of the potential core is identified to cause the transitional response of the stagnation heat transfer to the inclination of the circular jet. The inclination and convexity are demonstrated to thicken the boundary layer, reducing the local heat transfer (second peaks) as opposed to the enhanced local heat transfer on a flat plate resulting from the increased local Reynolds number.

Sign in / Sign up

Export Citation Format

Share Document