scholarly journals Condensation of Refrigerants HCF C 22, HFC 134a and HCFC 123 in a Horizontal Smooth Tube. 1st Report, Proposals of Empirical Expressions for the Local Frictional Pressure Drop.

1994 ◽  
Vol 60 (574) ◽  
pp. 2111-2116 ◽  
Author(s):  
Hidetaka Haraguchi ◽  
Shigeru Koyama ◽  
Tetsu Fujii
Keyword(s):  
Pressure Drop ◽  
Smooth Tube ◽  
Empirical Expressions ◽  
Frictional Pressure Drop ◽  
Hfc 134A ◽  
Hcfc 123

Evaluation of Existing Frictional Pressure Drop Correlations During Condensation of R410A in Four Horizontal Tubes

2019 ◽  
Author(s):  
Kunrong Shen ◽  
Zhichuan Sun ◽  
Wei Li ◽  
Xiang Ma ◽  
Yan He ◽  
...  
Keyword(s):  
Experimental Data ◽  
Pressure Drop ◽  
Flow Model ◽  
Saturation Temperature ◽  
Separated Flow ◽  
Smooth Tube ◽  
Outer Diameter ◽  
Homogeneous Flow ◽  
Frictional Pressure Drop ◽  
Horizontal Tubes

Abstract Results are presented here from an experimental investigation on tube side condensation characteristics that took place in four tested tubes — 1EHT-1, 1EHT-2, 4LB and a smooth tube. The equivalent outer diameter of the tubes was 9.52 mm and the inner diameter was 8.32 mm. Condensation tests were conducted using refrigerant R410A at a saturation temperature of 318K, over a mass flow range of 150–450 kgm−2s−1, with inlet and outlet vapor quality of 0.8 and 0.2, respectively. Pressure drop data of the four tested tubes were collected to evaluate five identified prediction correlations based on the separated flow model and the homogeneous flow model. For 1EHT-2 and the smooth tube, all the listed correlations manage to present predictions with the Mean Absolute Relative Deviation (MARD) less than 30%, while they underestimate the frictional pressure drop of the 4LB tube with MARD exceeding 40% averagely. Regarding the experimental data, it is found that the Muller-Steinhagen and Heck correlation presents the most accurate and stable prediction for the 4 tested tubes. The listed homogeneous flow correlations can provide acceptable predictions with MARD ranging from 25% to 40% under a few conditions, but their average predictive accuracies are inferior to that of the separated flow correlations. Consequently, the separated flow approach performs better than the homogeneous flow model in the prediction of frictional pressure drop for our experimental data.

Experimental Study of Evaporation Frictional Pressure Drop in Horizontal Enhanced Tube

2020 ◽  
Author(s):  
Zong-bao Gu ◽  
Yu Guo ◽  
Xiang Ma ◽  
Yan He ◽  
Wei Li
Keyword(s):  
Pressure Drop ◽  
Mass Flux ◽  
Three Dimensional ◽  
Saturation Temperature ◽  
Smooth Tube ◽  
Working Fluid ◽  
Outer Diameter ◽  
Vapor Quality ◽  
Frictional Pressure Drop ◽  
Enhanced Tube

Abstract An experimental investigation for evaporation frictional pressure drop in horizontal enhanced tubes with an outer diameter of 12.7 mm was studied using R410A as the working fluid. The experiment was conducted: the mass flux in the range of 100 kg/(m2s) to 200 kg/(m2s), over a vapor quality range of 0.2 to 0.8, an average saturation temperature at 279 K. The inner tubes were the tested tubes, which included a smooth tube, a three-dimensional enhanced tube (a tube enhanced by protrusions and petal arrays background patterns), respectively. The results show that the frictional pressure drop increases with the mass flux increasing. Moreover, the frictional pressure drop of the enhanced tube is 1.6∼2.4 times than that of the smooth tube. This is mainly due to the increase of the flow resistance inside the enhanced tube, which is caused by the increased interfacial turbulence, flow separation and secondary flow. It is also observed that the pressure drop increases with vapor quality increasing. In addition, some existing correlations are used to compare with our experimental data and verify their accuracy. A new modified correlation is proposed to predict the frictional pressure drop of EHT-1 tube.

Effects of Pitch and Depth on the Condensation Heat Transfer of R-134a Flowing Through Corrugated Tubes

2011 ◽  
Author(s):  
Suriyan Laohalertdecha ◽  
Somchai Wongwises
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Heat Exchanger ◽  
Pressure Drop ◽  
Transfer Coefficient ◽  
Condensation Heat Transfer ◽  
Smooth Tube ◽  
Maximum Heat ◽  
Frictional Pressure Drop ◽  
R 134A

The effects of pitch and depth on the condensation heat transfer of R-134a flowing inside corrugated tubes are experimentally investigated. The test section is a horizontal tube-in-tube heat exchanger. The refrigerant flows in the inner tube and the water flows in the annulus. The length of heat exchanger is 2 m. A smooth tube and corrugated tubes having inner diameters of 8.7 mm are used as an inner tube. The corrugation pitches used in this study are 5.08, 6.35, and 8.46 mm. Similarly, the corrugation depths are 1, 1.25, and 1.5 mm. The effects of corrugation pitch and depth on tube wall temperature, heat transfer coefficient and frictional pressure drop are discussed. The results illustrate that the maximum heat transfer coefficient and frictional pressure drop obtained from the corrugated tube are up to 50% and 70% higher than those obtained from the smooth tube, respectively.

PRESSURE DROP CHARACTERISTICS OF R410A-OIL MIXTURE FLOW BOILING IN SMALL SMOOTH TUBES

2010 ◽  
Vol 18 (02) ◽  
pp. 109-116 ◽  
Author(s):  
YIFENG GAO ◽  
BIN DENG ◽  
GUOLIANG DING ◽  
HAITAO HU ◽  
XIANGCHAO HUANG
Keyword(s):  
Pressure Drop ◽  
Flow Boiling ◽  
Smooth Tube ◽  
Two Phase ◽  
Experimental Conditions ◽  
Mixture Flow ◽  
Frictional Pressure Drop ◽  
New Correlation ◽  
Smooth Tubes ◽  
Local Properties

This study presents experimental frictional pressure drop for R410A/oil mixture flow boiling in small horizontal smooth tubes with inside diameters of 4.18 mm and 2.0 mm. Experimental conditions cover nominal oil concentrations from 0 to 5%. The test results show that the presence of oil enhances two-phase frictional pressure drop about 0–120% and 0–90% at present test conditions for 4.18 mm I.D. smooth tube and 2.0 mm I.D. smooth tube, respectively, and the enhanced effect is more evident at higher vapor qualities where the local oil concentrations are higher. A new correlation to predict the local frictional pressure drop of R410A/oil mixture flow boiling inside conventional size and small smooth tubes is developed based on local properties of refrigerant–oil mixture, and the experimental data of 4.18 mm I.D. and 2.0 mm I.D. smooth tubes and that of 6.34 mm I.D. smooth tube (Hu et al., 2008) are well-correlated with the new correlation.

Experimental Investigation of Flow Boiling Pressure Drop of R134A in a Microscale Horizontal Smooth Tube

2011 ◽  
Vol 3 (1) ◽  
Author(s):  
Cristiano Bigonha Tibiriçá ◽  
Jaqueline Diniz da Silva ◽  
Gherhardt Ribatski
Keyword(s):  
Pressure Drop ◽  
High Speed ◽  
Flow Boiling ◽  
Smooth Tube ◽  
Working Fluid ◽  
Prediction Methods ◽  
Internal Diameter ◽  
Two Phase ◽  
Pressure Drops ◽  
Frictional Pressure Drop

This paper presents new experimental flow boiling pressure drop results in a microscale tube. The experimental data were obtained under diabatic conditions in a horizontal smooth tube with an internal diameter of 2.32 mm. Experiments were performed with R134a as working fluid, mass velocities ranging from 100 kg/m2 s to 600 kg/m2 s, heat flux ranging from 10 kW/m2 to 55 kW/m2, saturation temperatures of 31°C, and exit vapor qualities from 0.20 to 0.99. Flow pattern characterization was also performed from images obtained by high-speed filming. Pressure drop gradients up to 48 kPa/m were measured. These data were carefully analyzed and compared against 13 two-phase frictional pressure drop prediction methods, including both macro- and microscale methods. Comparisons against these methods based on the data segregated according to flow patterns were also performed. Overall, the method by Cioncolini et al. (2009, “Unified Macro-to-Microscale Method to Predict Two-Phase Frictional Pressure Drops of Annular Flows,” Int. J. Multiphase Flow, 35, pp. 1138–1148) provided quite accurate predictions of the present database.

Measurement and Correlation of Frictional Pressure Drop of R-410A/Oil Mixture Flow Boiling in a 7 mm Straight Smooth Tube

2008 ◽  
Vol 14 (5) ◽  
pp. 763-781 ◽  
Author(s):  
Haitao Hu ◽  
Guoliang Ding ◽  
Wenjian Wei ◽  
Zhence Wang ◽  
Kaijian Wang
Keyword(s):  
Pressure Drop ◽  
Flow Boiling ◽  
Smooth Tube ◽  
Mixture Flow ◽  
Frictional Pressure Drop

Adiabatic Horizontal and Vertical Pressure Drop of Carbon Dioxide Inside Smooth and Microfin Tubes at Low Temperatures

2008 ◽  
Vol 130 (11) ◽  
Author(s):  
Yoon Jo Kim ◽  
Jeremy Jang ◽  
Predrag S. Hrnjak ◽  
Min Soo Kim
Keyword(s):  
Pressure Drop ◽  
Mass Flux ◽  
Two Phase Flow ◽  
Interfacial Shear Stress ◽  
Smooth Tube ◽  
Phase Flow ◽  
Two Phase ◽  
Vertical Pressure ◽  
Frictional Pressure Drop ◽  
Microfin Tubes

This paper presents the pressure drop data and the analysis of adiabatic CO2 flow in horizontal and vertical smooth and microfin tubes at saturation temperatures around −20°C. The test tubes had 3.48mm inner diameter smooth tube and a 3.51mm melt-down diameter microfin tube. The test was performed over a mass flux range of 200–800kg∕m2s and at saturation temperatures of −25°C and −15°C. The effects of various parameters—mass flux, saturated temperature, and tube diameter—on pressure drop were qualitatively analyzed. The analyses showed that the frictional pressure drop characteristics of vertical two-phase flow were much different from that of the horizontal two-phase flow. The microfin tube can be considered as “very rough tube” having the roughness of “fin height.” The data were compared with several correlations. The existing frictional pressure drop correlation is sufficient to predict the horizontal pressure drop in smooth tube. For the vertical pressure drop, the simple combination of the frictional pressure drop and void fraction model was in comparatively good agreement. However, the qualitative results showed that there were some limits to cover the different mechanisms related to the interfacial shear stress. The average enhancement factors and penalty factors evidenced that it was not always true that the internally finned geometry guaranteed the superior in-tube condensation performance of microfin tube in refrigeration system and air-conditioning systems.

Experimental Investigation of Flow Boiling Pressure Drop of R134a in a Micro-Scale Horizontal Smooth Tube

2010 ◽  
Author(s):  
Cristiano Bigonha Tibiric¸a´ ◽  
Gherhardt Ribatski
Keyword(s):  
Pressure Drop ◽  
High Speed ◽  
Flow Boiling ◽  
Smooth Tube ◽  
Working Fluid ◽  
Internal Diameter ◽  
Two Phase ◽  
Pressure Drops ◽  
Micro Scale ◽  
Frictional Pressure Drop

This paper presents new experimental flow boiling pressure drop results in a microscale tube. The experimental data were obtained under diabatic conditions in a horizontal smooth tube with internal diameter of 2.3 mm. Experiments were performed with R134a as working fluid, mass velocities ranging from 100 to 600 kg/m2s, heat flux ranging from 10 to 55 kW/m2, saturation temperatures of 31 °C, and exit vapor qualities from 0.20 to 0.99. Flow pattern characterization was also performed from images obtained by high-speed filming. Pressure drops up to 48 kPa/m were measured. These data were carefully analyzed and compared against 13 two-phase frictional pressure drop prediction methods, including both macro- and micro-scale methods. Comparisons against these methods based on the data segregated according to flow patterns were also performed. Overall, the method by Cioncolini et al. [1] provided quite accurate predictions of the present database.

Sign in / Sign up

Export Citation Format

Share Document