scholarly journals Cloud Point Extraction and Spectrophotometric Studies for the Extraction of Nigrosin and Aniline Blue Dyes using Mixed Micelles of TBAB and Triton X-114

2021 ◽  
Vol 33 (6) ◽  
pp. 1351-1356
Author(s):  
D. Radhakrishna ◽  
D. Suneetha ◽  
P. Shyamala
Keyword(s):  
Cloud Point ◽  
Mixed Micelles ◽  
Extraction Efficiency ◽  
Cloud Point Extraction ◽  
Sea Water ◽  
Limit Of Detection ◽  
Tetrabutylammonium Bromide ◽  
Aniline Blue ◽  
Ionic Surfactant ◽  
Triton X

The extractions of two anionic dyes viz. nigrosin and aniline blue by cloud point extraction method using mixed micelles of tetrabutylammonium bromide (TBAB) and Triton X-114 were conducted. To get the greatest extraction efficiency, pH of the solution, surfactant concentration, concentration of electrolyte, equilibrium temperature and time were optimized. A linear calibration curve in the range of 0.567-9.07 mg/L (nigrosin) and 0.982-19.645 mg/L (aniline blue) was obtained. Limit of detection were found to be 2.45 ng/L and 2.008 ng/L for nigrosin and aniline blue dyes, respectively. Thermodynamic parameters were also calculated to establish the feasibility of the process. This method was then used to determine the dyes in tap and sea water samples. The extraction efficiency was explained in terms of dye surfactant interaction as shown by observed spectral changes between anionic dye and cationic surfactant followed by solubilization of the complex in non-ionic surfactant.

scholarly journals Cloud point extraction and preconcentration of gold in geological matrices prior to flame atomic absorption determination

2010 ◽  
Vol 8 (1) ◽  
pp. 34-40 ◽  
Author(s):  
Wifky El-Naggar ◽  
Taysseer Lasheen ◽  
El-Said Nouh ◽  
Ahmed Ghonaim
Keyword(s):  
Atomic Absorption ◽  
Cloud Point ◽  
Cloud Point Extraction ◽  
Limit Of Detection ◽  
Absorption Spectrometry ◽  
Complexing Agent ◽  
Rich Phase ◽  
Flame Atomic Absorption ◽  
Initial Aqueous Solution ◽  
Triton X

AbstractBrilliant green was used as a complexing agent in cloud point extraction (CPE) and applied for selective preconcentration of trace amounts of gold in geological matrices. The analyte in the initial aqueous solution was acidified with hydrochloric acid (0.1 M) and octylphenoxypolyethoxyethanol (Triton X-114) was added as a surfactant. After phase separation, based on the cloud point separation of the mixture, the surfactant rich phase was diluted with methanol and the analyte determined in the surfactant rich phase by flame atomic absorption spectrometry (FAAS). After optimization of the complexation and extraction conditions, a preconcentration factor of 31 was obtained for only 10 mL of sample. The analytical curve was linear in the range of 3–1000 ng mL−1 and the limit of detection was 1.5 ng mL−1. The proposed method was applied to the determination of gold in geological samples.

scholarly journals Development of a Cloud-Point Extraction Method for Cobalt Determination in Natural Water Samples

2013 ◽  
Vol 2013 ◽  
pp. 1-7 ◽  
Author(s):  
Mohammad Reza Jamali ◽  
Mohammad Gholinezhad ◽  
Saiedeh Balarostaghi ◽  
Reyhaneh Rahnama ◽  
Seyed Hojjat Allah Rahimi
Keyword(s):  
Cloud Point ◽  
Water Samples ◽  
Cloud Point Extraction ◽  
Limit Of Detection ◽  
Cobalt Content ◽  
Cobalt Ions ◽  
Flame Atomic Absorption ◽  
Relative Standard ◽  
Separation And Preconcentration ◽  
Triton X

A new, simple, and versatile cloud-point extraction (CPE) methodology has been developed for the separation and preconcentration of cobalt. The cobalt ions in the initial aqueous solution were complexed with 4-Benzylpiperidinedithiocarbamate, and Triton X-114 was added as surfactant. Dilution of the surfactant-rich phase with acidified ethanol was performed after phase separation, and the cobalt content was measured by flame atomic absorption spectrometry. The main factors affecting CPE procedure, such as pH, concentration of ligand, amount of Triton X-114, equilibrium temperature, and incubation time were investigated and optimized. Under the optimal conditions, the limit of detection (LOD) for cobalt was 0.5 μg L-1, with sensitivity enhancement factor (EF) of 67. Calibration curve was linear in the range of 2–150 μg L-1, and relative standard deviation was 3.2% (c=100 μg L-1;n=10). The proposed method was applied to the determination of trace cobalt in real water samples with satisfactory analytical results.

scholarly journals Determination of Antidepressants in Human Plasma by Modified Cloud-Point Extraction Coupled with Mass Spectrometry

2020 ◽  
Vol 13 (12) ◽  
pp. 458
Author(s):  
Elżbieta Gniazdowska ◽  
Natalia Korytowska ◽  
Grzegorz Kłudka ◽  
Joanna Giebułtowicz
Keyword(s):  
Mass Spectrometry ◽  
Simultaneous Determination ◽  
Human Plasma ◽  
Cloud Point ◽  
Extraction Efficiency ◽  
Cloud Point Extraction ◽  
Limiting Factor ◽  
Drug Determination ◽  
Triton X

Cloud-point extraction (CPE) is rarely combined with liquid chromatography coupled to mass spectrometry (LC–MS) in drug determination due to the matrix effect (ME). However, we have recently shown that ME is not a limiting factor in CPE. Low extraction efficiency may be improved by salt addition, but none of the salts used in CPE are suitable for LC–MS. It is the first time that the influences of a volatile salt—ammonium acetate (AA)—on the CPE extraction efficiency and ME have been studied. Our modification of CPE included also the use of ethanol instead of acetonitrile to reduce the sample viscosity and make the method more environmentally friendly. We developed and validated CPE–LC–MS for the simultaneous determination of 21 antidepressants in plasma that can be useful for clinical and forensic toxicology. The selected parameters included Triton X-114 concentration (1.5 and 6%, w/v), concentration of AA (0, 10, 20 and 30%, w/v), and pH (3.5, 6.8 and 10.2). The addition of 10% of AA increased recovery twice. For 20 and 30% (w/v) of AA, three phases were formed that prolonged the extraction process. The developed CPE method (6% Triton X-114, 10% AA, pH 10.2) was successfully validated through LC–MS/MS simultaneous determination of 21 antidepressants in human plasma. The linearity was in the range of 10–750 ng/mL (r2 > 0.990).

scholarly journals Improvement of a 'SSQuEE' Method for Recovery and Preconcentration of Pesticides from Environmental Samples

2021 ◽  
Vol 33 (10) ◽  
pp. 2472-2476
Author(s):  
Rajib Joarder
Keyword(s):  
Cloud Point ◽  
High Performance ◽  
Limit Of Detection ◽  
Ionic Surfactant ◽  
Analytical Technique ◽  
Liquid Chromatography Separation ◽  
Cloud Point Temperature ◽  
Triton X ◽  
Optimum Extraction

A simple, sensitive, quick, easy and efficient (SSQuEE) analytical technique based on cloud point extraction (CPE) has been developed for the determination of different pesticides present in soil and water with high performance liquid chromatography separation and ultraviolet detection. The environmentally friendliness surfactant like Triton X -100, compared to Tween series of non-ionic surfactant can effectively extract imidacloprid (insecticide), flusilazole (fungicide) and atrazine (herbicide) at cloud point temperature at 67 ºC, 82 ºC and 62 ºC, respectively. To reach the optimum extraction efficiency, different experimental parameters like surfactant concentration, salt type and its concentration, equilibrium time and temperature, pH were observed. At the optimum conditions, linear regression coefficient of the standard curves was greater than 0.9924. The limit of detection of imidacloprid, flusilazole and atrazine were 0.10 μg L-1, 0.24 μg L-1, 0.15 μg L-1 and recovery percent are 99.71 %, 88.1% and 89.74%, respectively.

A cloud point extraction procedure for gallium, indium and thallium determination in liquid crystal display and sediment samples

2015 ◽  
Vol 7 (5) ◽  
pp. 2114-2120 ◽  
Author(s):  
Wael I. Mortada ◽  
Ibrahim M. Kenawy ◽  
Mohamed M. Hassanien
Keyword(s):  
Liquid Crystal ◽  
Cloud Point ◽  
Cloud Point Extraction ◽  
Liquid Crystal Display ◽  
Extraction Procedure ◽  
Ionic Surfactant ◽  
Sediment Samples ◽  
Separation And Preconcentration ◽  
Thallium Determination ◽  
Triton X

A simple, sensitive and rapid cloud point extraction (CPE) methodology has been developed for the selective separation and preconcentration of gallium, indium and thallium, after complexation with gallic acid in the presence of Triton X-114 as a non-ionic surfactant.

scholarly journals Cloud Point Extraction of Toxic Reactive Black 5 Dye from Water Samples Using Triton X-100 as Nonionic Surfactant

2011 ◽  
Vol 8 (4) ◽  
pp. 1606-1613 ◽  
Author(s):  
Raziyeh Mousavi ◽  
Farzin Nekouei
Keyword(s):  
Cloud Point ◽  
Salt Concentration ◽  
Water Samples ◽  
Cloud Point Extraction ◽  
Extraction Procedure ◽  
Ionic Surfactant ◽  
Reactive Black 5 ◽  
Optimum Conditions ◽  
Single Extraction ◽  
Triton X

A surfactant mediated cloud point extraction (CPE) procedure has been developed to remove color from wastewater containing reactive black 5, using triton x-100 (TX-100) as non-ionic surfactant. The effects of the concentration of the surfactant, pH, temperature and salt concentration on the different concentrations of dye have been studied and optimum conditions were obtained for the removal of reactive black 5 (RB 5). The concentration of RB 5 in the dilute phase was measured using UV-Vis spectrophotometer. It was found that the separation of phases was complete and the recovery of RB 5 was very effective in the presence of NaCl as an electrolyte. The results showed that up to 600 mg L-1of RB 5 can quantitatively be removed (>97%) by cloud point extraction procedure in a single extraction using optimum conditions.

Cloud Point Extraction of Direct Blue 71 Dye using Triton X-100 as Nonionic Surfactant

2021 ◽  
Vol 58 (1) ◽  
pp. 27-32
Author(s):  
Moussa Alibrahim
Keyword(s):  
Cloud Point ◽  
Salt Concentration ◽  
Dye Removal ◽  
Cloud Point Extraction ◽  
Blue Dye ◽  
Ionic Surfactant ◽  
Optimal Conditions ◽  
Direct Blue ◽  
Triton X ◽  
Direct Blue 71

Abstract A surfactant-mediated cloud point extraction (CPE) method using the non-ionic surfactant Triton X-100 (TX-100) has been developed to remove the dye Direct Blue 71 (DB71) from a waste water. Most of the dye molecules are solubilized in the coacervate phase so that the dilute phase remains free of the dye. The effects of surfactant concentration, temperature and salt concentration on the different dye concentrations were studied to determine the optimal conditions for removing DB71. The concentration of DB71 in the dilute phase was measured using UV-Vis spectrophotometer. It was found that the separation of phases was complete and the recovery of DB71 was very effective in the presence of NaCl as an electrolyte. The results showed that up to 25 ppm DB71, i.e. more than 95%, can be quantitatively removed by cloud point extraction procedures in a single extraction at optimal conditions. It was also observed that at a dye concentration of 1 ppm, 100% of the blue dye DB71 can be directly removed with a TX-100 concentration of 12% by weight. At higher dye concentrations of up to 30 ppm, 94.7%-100% dye can be removed. The TX-100 concentration was 12 wt%, the salt concentration (NaCl) 0.005 M and the temperature 75°C. It is concluded that the surfactant mediated cloud point extraction method for dye removal can be an alternative to current dye removal methods.

scholarly journals Cloud-Point Extraction of Rhodamine 6G by Using Triton X-100 as the Non-Ionic Surfactant

2011 ◽  
Vol 94 (1) ◽  
pp. 286-292 ◽  
Author(s):  
Celal Duran ◽  
Duygu Ozdes ◽  
Volkan Numan Bulut ◽  
Mehmet Tufekcī ◽  
Mustafa Soylak
Keyword(s):  
Cloud Point ◽  
Rhodamine 6G ◽  
Cloud Point Extraction ◽  
Equilibrium Temperature ◽  
Isotherm Models ◽  
Ionic Surfactant ◽  
Water And Wastewater ◽  
Dye Extraction ◽  
Triton X ◽  
Significant Interference

Abstract Cloud-point extraction (CPE) using the non-ionic surfactant Triton X-100 was used successfully to remove a highly toxic dye, rhodamine 6G (R6G), from water and wastewater. The effects of different analytical parameters such as pH, concentration of Triton X-100 (TX-100) and salts, equilibrium temperature, and incubation time on the efficiency of the extraction of R6G were studied in detail, and optimum conditions for dye extraction were obtained. Thermodynamic parameters including changes in Gibbs free energy, enthalpy, and entropy were also calculated, and these parameters indicated that the CPE of R6G was feasible, spontaneous, and endothermic in the temperature range of 75–95°C. The equilibrium solubilization capacity of TX-100 was found to be 1.10 mmol/mol by using Langmuir isotherm models. No significant interference effects were observed in the presence of phenol and its derivatives, some acidic and basic dyes and most of the anions and cations. It was concluded that the CPE process described in this paper can be an alternative technique for removal of dyes and other pollutants from waters and wastewaters.

scholarly journals Room temperature cloud point extraction: An application to preconcentration and spectrophotometric determination of copper(II)

2020 ◽  
Vol 85 (1) ◽  
pp. 89-96 ◽  
Author(s):  
Denys Snigur ◽  
Alexander Chebotarev ◽  
Vitaliy Dubovyi ◽  
Dmytro Barbalat ◽  
Anastasiia Klochkova
Keyword(s):  
Sulfuric Acid ◽  
Cloud Point ◽  
Spectrophotometric Determination ◽  
Cloud Point Extraction ◽  
Limit Of Detection ◽  
Extraction Procedure ◽  
Rich Phase ◽  
Triton X ◽  
Determination Of Copper

The novel cloud point extraction procedure for preconcentration of copper(II) was discovered. A simple chemical method for initiating the cloud point extraction (CPE) has been proposed. The formation of surfactant rich phase in a system containing a nonionic surfactant Triton X-100, copper(II), 6,7-dihydroxy-4-methyl-2-phenylbenzopyrilium chloride (DHMPhB) and ammonium benzoate is observed immediately upon the sulfuric acid addition into solution. Under the optimal conditions (absorption band maximum was 540 nm, concentration 1.5?10-4 mol dm-3 of DHMPhB, 1.0 vol.% of Triton X-100, 2.0 cm3 of 0.75 mol dm-3 ammonium benzoate, and 1.0 cm3 of 0.5 mol dm-3 sulfuric acid solution for obtaining benzoic?benzoate buffer solution with pH 4.5 and initiation immediate surfactant rich phase formation) the calibration plot for spectrophotometric determination of copper(II) was linear in the range of copper(II) concentration 0.02?0.95 ?g cm?3. The limit of detection was calculated 0.006 ?g cm?3. The water samples were analyzed according to a suggested procedure with satisfactory results.

Sign in / Sign up

Export Citation Format

Share Document