scholarly journals Shale volume and porosity delineation of coast swamp depobelt in Niger delta region, Nigeria, using well log

2019 ◽  
Vol 7 (2) ◽  
pp. 142
Author(s):  
Ubong Essien
Keyword(s):  
Niger Delta ◽  
Gamma Ray ◽  
Water Saturation ◽  
Effective Porosity ◽  
Neutron Density ◽  
Well Log ◽  
Shale Formations ◽  
Log Data ◽  
Shale Volume ◽  
Niger Delta Region

Well log data from two wells were evaluated for shale volume, total and effective porosity. Well log data were obtained from gamma ray, neutron-density log, resistivity, sonic and caliper log respectively. This study aimed at evaluating the effect of shale volume, total and effective porosity form two well log data. The results of the analysis depict the presence of sand, sand-shale and shale formations. Hydrocarbon accumulation were found to be high in sand, fair in sand-shale and low in shale, since existence of shale reduces total and effective porosity and water saturation of the reservoir. The thickness of the reservoir ranged from 66 – 248.5ft. The average values of volume of shale, total and effective porosity values ranged from 0.004 – 0.299dec, 0.178 – 0.207dec and 0.154 – 0.194dec. Similarly, the water saturation and permeability ranged from 0.277 – 0.447dec and 36.637 - 7808.519md respectively. These values of total and effective porosity are high in sand, fair in sand-shale and low in shale formations. The results for this study demonstrate: accuracy, applicability of these approaches and enhance the proper evaluation of petrophysical parameters from well log data.    

scholarly journals Evaluation of shale volume and effective porosity using larionov and archie equations from wire-line logs, Niger delta Nigeria

2019 ◽  
Vol 8 (4) ◽  
pp. 257
Author(s):  
Mfoniso U. Aka ◽  
Johnson Cletus Ibuot ◽  
Francisca N. Okeke
Keyword(s):  
Niger Delta ◽  
Water Saturation ◽  
Effective Porosity ◽  
Well Log ◽  
Reservoir Properties ◽  
Shale Formations ◽  
Shale Volume ◽  
Niger Delta Region ◽  
Rock Formations ◽  
Water Resistivity

<p>In Niger Delta region of Nigeria, reservoirs are mostly loose and unstratified sands to hold fluids. In this paper, three different wells in central Niger Delta were assessed for shale volume and actual porosity. The results of the analysis delineate the presence of sand, sand-shale and shale formations. Hydrocarbon prospecting was found to be strong in sand, moderate in sandshale and shallow in shale respectively. However, existent of shale lessens effective porosity and water saturation of the rock formations. The extent of the formation extends from 1300 to 2500 m. Shale volume and actual porosity values extend from 0.00 to 0.302 dec and 0.047 to 0.302 dec which decrease with increasing depth. Comparably, the water saturation and water resistivity extend from 0.432 to 0.779 dec and 0.106 to 2.918 Ohm respectively. These values of actual porosity are strong in sand, moderate in sand-shale and shallow in shale formations. The results from this assessment proof well log a vital and easier tool in assessing of reservoir properties.</p>

scholarly journals Shale volume and permeability of the Miocene unconsolidated turbidite sands of Bonga oil field, Niger delta, Nigeria

2017 ◽  
Vol 5 (1) ◽  
pp. 37 ◽  
Author(s):  
Inyang Namdie ◽  
Idara Akpabio ◽  
Agbasi Okechukwu .E.
Keyword(s):  
Niger Delta ◽  
Gamma Ray ◽  
Water Saturation ◽  
Strong Dependence ◽  
Water Injection ◽  
Oil Field ◽  
Reservoir Properties ◽  
Injection Wells ◽  
Log Data ◽  
Shale Volume

Bonga oil field is located 120km (75mi) southeast of the Niger Delta, Nigeria. It is a subsea type development located about 3500ft water depth and has produced over 330 mmstb of hydrocarbon till date with over 16 oil producing and water injection wells. The producing formation is the Middle to Late Miocene unconsolidated turbidite sandstones with lateral and vertical homogeneities in reservoir properties. This work, analysis the petrophysical properties of the reservoir units for the purpose of modeling the effect of shale content on permeability in the reservoir. Turbidite sandstones are identified by gamma-ray log signatures as intervals with 26-50 API, while sonic, neutron, resistivity, caliper and other log data are applied to estimate volume of shale ranging between 0.972 v/v for shale intervals and 0.0549 v/v for turbidite sands, water saturation of 0.34 v/v average in most sand intervals, porosity range from 0.010 for shale intervals to 0.49 v/v for clean sands and permeability values for the send interval 11.46 to2634mD, for intervals between 7100 to 9100 ft., Data were analyzed using the Interactive Petrophysical software that splits the whole curve into sand and shale zones and estimates among other petrophysical parameters the shale contents of the prospective zones. While Seismic data revealed reservoir thickness ranging from 25ft to over 140ft well log data within the five wells have identified sands of similar thickness and estimated average permeability of700mD. Within the sand units across the five wells, cross plots of estimated porosity, volume of shale and permeability values reveal strong dependence of permeability on shale volume and a general decrease in permeability in intervals with shale volume. It is concluded that sand units with high shale contents that are from0.500 to0.900v/v will not provide good quality reservoir in the field.

scholarly journals Hydrocarbon Reservoir Characterization of ‘Khume’ Field, Offshore Niger Delta, Nigeria

2021 ◽  
pp. 47-60
Author(s):  
K. A. Obakhume ◽  
O. M. Ekeng ◽  
C. Atuanya
Keyword(s):  
Niger Delta ◽  
Reservoir Characterization ◽  
Gamma Ray ◽  
Water Saturation ◽  
Seismic Interpretation ◽  
Effective Porosity ◽  
Well Logs ◽  
Integrative Approach ◽  
Neutron Density ◽  
Hydrocarbon Reservoir

The integrative approach of well log correlation and seismic interpretation was adopted in this study to adequately characterize and evaluate the hydrocarbon potentials of Khume field, offshore Niger Delta, Nigeria. 3-D seismic data and well logs data from ten (10) wells were utilized to delineate the geometry of the reservoirs in Khume field, and as well as to estimate the hydrocarbon reserves. Three hydrocarbon-bearing reservoirs of interest (D-04, D-06, and E-09A) were delineated using an array of gamma-ray logs, resistivity log, and neutron/density log suites. Stratigraphic interpretation of the lithologies in Khume field showed considerable uniform gross thickness across all three sand bodies. Results of petrophysical evaluations conducted on the three reservoirs correlated across the field showed that; shale volume ranged from 7-14%, total and effective porosity ranged from 19-26% and 17-23% respectively, NTG from 42 to 100%, water saturation from 40%-100% and permeability from 1265-2102 mD. Seismic interpretation established the presence of both synthetic and antithetic faults. A total of six synthetic and four antithetic faults were interpreted from the study area. Horizons interpretation was done both in the strike and dip directions. Time and depth structure maps revealed reservoir closures to be anticlinal and fault supported in the field. Hydrocarbon volumes were calculated using the deterministic (map-based) approach. Stock tank oil initially in place (STOIIP) for the proven oil column estimated for the D-04 reservoir was 11.13 MMSTB, 0.54 MMSTB for D-06, and 2.16 MMSTB for E-09A reservoir. For the possible oil reserves, a STOIIP value of 7.28 MMSTB was estimated for D-06 and 6.30 MMSTB for E-09A reservoir, while a hydrocarbon initially in place (HIIP) of 4.13 MMSTB of oil equivalents was derived for the undefined fluid (oil/gas) in D-06 reservoir. A proven gas reserve of 1.07 MMSCF was derived for the D-06 reservoir. This study demonstrated the effectiveness of 3-D seismic and well logs data in delineating reservoir structural architecture and in estimating hydrocarbon volumes

Evaluation of Reservoir’s Petrophysical Parameters, Niger Delta, Nigeria

2017 ◽  
Vol 5 (1) ◽  
pp. 19
Author(s):  
Ubong Essien ◽  
Akaninyene Akankpo ◽  
Okechukwu Agbasi
Keyword(s):  
Niger Delta ◽  
Gamma Ray ◽  
Water Saturation ◽  
Petrophysical Parameters ◽  
Niger Delta Region ◽  
Average Porosity ◽  
Irreducible Water Saturation ◽  
Open Hole ◽  
Bulk Volume ◽  
Niger Delta Basin

Petrophysical analysis was performed in two wells in the Niger Delta Region, Nigeria. This study is aimed at making available petrophysical data, basically water saturation calculation using cementation values of 2.0 for the reservoir formations of two wells in the Niger delta basin. A suite of geophysical open hole logs namely Gamma ray; Resistivity, Sonic, Caliper and Density were used to determine petrophysical parameters. The parameters determined are; volume of shale, porosity, water saturation, irreducible water saturation and bulk volume of water. The thickness of the reservoir varies between 127ft and 1620ft. Average porosity values vary between 0.061 and 0.600; generally decreasing with depth. The mean average computed values for the Petrophysical parameters for the reservoirs are: Bulk Volume of Water, 0.070 to 0.175; Apparent Water Resistivity, 0.239 to 7.969; Water Saturation, 0.229 to 0.749; Irreducible Water Saturation, 0.229 to 0.882 and Volume of Shale, 0.045 to 0.355. The findings will also enhance the proper characterization of the reservoir sands.

scholarly journals Petrophysical Properties and Digenetic Evolution of Shuaiba Formation in Nasiriyah Oil Field, Southern Iraq

2021 ◽  
pp. 4810-4818
Author(s):  
Marwah H. Khudhair
Keyword(s):  
Gamma Ray ◽  
Water Saturation ◽  
Middle Part ◽  
Effective Porosity ◽  
Oil Field ◽  
Neutron Density ◽  
Petrophysical Properties ◽  
Secondary Porosity ◽  
Primary Porosity ◽  
Gamma Ray Log

     Shuaiba Formation is a carbonate succession deposited within Aptian Sequences. This research deals with the petrophysical and reservoir characterizations characteristics of the interval of interest in five wells of the Nasiriyah oil field. The petrophysical properties were determined by using different types of well logs, such as electric logs (LLS, LLD, MFSL), porosity logs (neutron, density, sonic), as well as gamma ray log. The studied sequence was mostly affected by dolomitization, which changed the lithology of the formation to dolostone and enhanced the secondary porosity that replaced the primary porosity. Depending on gamma ray log response and the shale volume, the formation is classified into three zones. These zones are A, B, and C, each can be split into three rock intervals in respect to the bulk porosity measurements. The resulted porosity intervals are: (I) High to medium effective porosity, (II) High to medium inactive porosity, and (III) Low or non-porosity intervals. In relevance to porosity, resistivity, and water saturation points of view, there are two main reservoir horizon intervals within Shuaiba Formation. Both horizons appear in the middle part of the formation, being located within the wells Ns-1, 2, and 3. These intervals are attributed to high to medium effective porosity, low shale content, and high values of the deep resistivity logs. The second horizon appears clearly in Ns-2 well only.

scholarly journals Prospect evaluation and hydrocarbon potential assessment: the Lower Eocene Facha non-clastic reservoirs, Hakim Oil Field (NC74A), Sirte basin, Libya—a case study

2019 ◽  
Vol 10 (2) ◽  
pp. 351-362 ◽  
Author(s):  
Mohamed A. Kassab ◽  
Ali El-Said Abbas ◽  
Mostafa A. Teama ◽  
Musa A. S. Khalifa
Keyword(s):  
Gamma Ray ◽  
Water Saturation ◽  
Oil Field ◽  
Thickness Variation ◽  
Oil Accumulation ◽  
Lower Eocene ◽  
Log Data ◽  
Shale Volume ◽  
Volume Porosity ◽  
Sirte Basin

Abstract Petrophysical assessment of Facha Formation based on log data of six wells A1, A3, A4, A5, A8 and A13 recorded over the entire reservoir interval was established. Hakim Oil Field produces from the Lower Eocene Facha reservoir, which is located at the western side of Sirte basin. Limestone, dolostone and dolomitic limestone are the main lithologies of the Facha reservoir. This lithology is defined by neutron porosity—density cross-plot. Noteworthily, limestone increases in the lowermost intervals of the reservoir. Structurally, the field is traversed by three northwest–southeast faults. The shale of the Upper Cretaceous Sirte Formation is thought to be the source rock of the Facha Formation, whereas the seals are the limestone and anhydrite of the Lower Eocene Gir Formation. In this study, the Facha reservoir’s cutoff values were obtained from the cross-plots of the calculated shale volume, porosity and water saturation values accompanied with gamma ray log data and were set as 20%, 10% and 70%, respectively. Isoparametric maps for the thickness variation of net pay, average porosity, shale volume and water saturation were prepared, and the authors found out that the Facha Formation has promising reservoir characteristics in the area of study; a prospective region for oil accumulation trends is in the north and south of the study area.

scholarly journals Hydrocarbon reservoir characterization of “Otan-Ile” field, Niger Delta

2021 ◽  
Vol 11 (2) ◽  
pp. 601-615
Author(s):  
Tokunbo Sanmi Fagbemigun ◽  
Michael Ayu Ayuk ◽  
Olufemi Enitan Oyanameh ◽  
Opeyemi Joshua Akinrinade ◽  
Joel Olayide Amosun ◽  
...  
Keyword(s):  
Niger Delta ◽  
Reservoir Characterization ◽  
Water Saturation ◽  
Structural Deformation ◽  
Well Log ◽  
Reservoir Properties ◽  
Good Tool ◽  
Log Data ◽  
Hydrocarbon Reservoir ◽  
Hydrocarbon Saturation

AbstractOtan-Ile field, located in the transition zone Niger Delta, is characterized by complex structural deformation and faulting which lead to high uncertainties of reservoir properties. These high uncertainties greatly affect the exploration and development of the Otan-Ile field, and thus require proper characterization. Reservoir characterization requires integration of different data such as seismic and well log data, which are used to develop proper reservoir model. Therefore, the objective of this study is to characterize the reservoir sand bodies across the Otan-Ile field and to evaluate the petrophysical parameters using 3-dimension seismic and well log data from four wells. Reservoir sands were delineated using combination of resistivity and gamma ray logs. The estimation of reservoir properties, such as gross thickness, net thickness, volume of shale, porosity, water saturation and hydrocarbon saturation, were done using standard equations. Two horizons (T and U) as well as major and minor faults were mapped across the ‘Otan-Ile’ field. The results show that the average net thickness, volume of shale, porosity, hydrocarbon saturation and permeability across the field are 28.19 m, 15%, 37%, 71% and 26,740.24 md respectively. Two major faults (F1 and F5) dipping in northeastern and northwestern direction were identified. The horizons were characterized by structural closures which can accommodate hydrocarbon were identified. Amplitude maps superimposed on depth-structure map also validate the hydrocarbon potential of the closures on it. This study shows that the integration of 3D seismic and well log data with seismic attribute is a good tool for proper hydrocarbon reservoir characterization.

scholarly journals Characterization of Mishrif Formation Reservoir in Amara Oil Field, Southeast Iraq, Using Geophysical Well-logging

2021 ◽  
pp. 4702-4711
Author(s):  
Asmaa Talal Fadel ◽  
Madhat E. Nasser
Keyword(s):  
Reservoir Characterization ◽  
Gamma Ray ◽  
Water Saturation ◽  
Total Porosity ◽  
Effective Porosity ◽  
Oil Field ◽  
Neutron Density ◽  
Reservoir Water ◽  
Resistivity Logs ◽  
Reliable Knowledge

     Reservoir characterization requires reliable knowledge of certain fundamental properties of the reservoir. These properties can be defined or at least inferred by log measurements, including porosity, resistivity, volume of shale, lithology, water saturation, and permeability of oil or gas. The current research is an estimate of the reservoir characteristics of Mishrif Formation in Amara Oil Field, particularly well AM-1, in south eastern Iraq. Mishrif Formation (Cenomanin-Early Touronin) is considered as the prime reservoir in Amara Oil Field. The Formation is divided into three reservoir units (MA, MB, MC). The unit MB is divided into two secondary units (MB1, MB2) while the unit MC is also divided into two secondary units (MC1, MC2). Using Geoframe software, the available well log images (sonic, density, neutron, gamma ray, spontaneous potential, and resistivity logs) were digitized and updated. Petrophysical properties, such as porosity, saturation of water, saturation of hydrocarbon, etc. were calculated and explained. The total porosity was measured using the density and neutron log, and then corrected to measure the effective porosity by the volume content of clay. Neutron -density cross-plot showed that Mishrif Formation lithology consists predominantly of limestone. The reservoir water resistivity (Rw) values of the Formation were calculated using Pickett-Plot method.   

Well logging data interpretation for appraising the performance of Alam El-Bueib reservoir in Safir Oil Field, Shushan Basin, Egypt

2021 ◽  
Vol 11 (5) ◽  
pp. 2075-2089
Author(s):  
Mohamed Mahmoud Elhossainy ◽  
Ahmed Kamal Basal ◽  
Hussein Tawfik ElBadrawy ◽  
Sobhy Abdel Salam ◽  
Mohammad Abdelfattah Sarhan
Keyword(s):  
Water Saturation ◽  
Data Interpretation ◽  
Effective Porosity ◽  
Oil Field ◽  
Reservoir Quality ◽  
Well Log ◽  
Relative Permeabilities ◽  
Log Data ◽  
Bulk Volume ◽  
Water Cut

AbstractThis paper presents different well log data interpretation techniques for evaluating the reservoir quality for the sandstone reservoir of the Alam El-Bueib-3A Member in Safir-03 well, Shushan Basin, Egypt. The evaluation of the available well log data for the Alam El-Bueib-3A Member in this well indicated high quality as oil-producing reservoir between depths 8108–8133 ft (25 ft thick). The calculated reservoir parameters possess shale volume less than or equal to 9% indicating the clean nature of this sandstone interval, water saturation values range from 10 to 23%, and effective porosity varies between 19 and 23%. Bulk volume of water is less than 0.04, non-producing water (SWirr) saturation varies between 10 and 12%, and permeability ranges from 393 to 1339 MD reflecting excellent reservoir quality. The calculated BVW values are less than the minimum (BVWmin = 0.05) reflecting clean (no water) oil production, which was confirmed through the drill stem test (DST). The relative permeabilities to both water and oil are located between 0.01–0 and 1.0–0.5, respectively. The water cut is fairly low where it ranges between 0 and 20%. Additionally, the water saturation values are less than the critical water saturation (Scw = 29.5%) which reflects that the whole net pay will flow hydrocarbon, whereas the water phase will remain immobile. This was confirmed with reservoir engineering through the DST.

scholarly journals Seismic Data Interpretation and Petrophysical Analysis of Kabirwala Area Tola (01) Well, Central Indus Basin, Pakistan

2021 ◽  
Vol 11 (7) ◽  
pp. 2911
Author(s):  
Naveed Ahmad ◽  
Sikandar Khan ◽  
Abdullatif Al-Shuhail
Keyword(s):  
Gamma Ray ◽  
Water Saturation ◽  
Research Work ◽  
Total Porosity ◽  
Effective Porosity ◽  
Indus Basin ◽  
Drilling Process ◽  
Reservoir Properties ◽  
Log Data ◽  
Petrophysical Analysis

Well logging is a significant procedure that assists geophysicists and geologists with making predictions regarding boreholes and efficiently utilizing and optimizing the drilling process. The current study area is positioned in the Punjab Territory of Pakistan, and the geographic coordinates are 30020′10 N and 70043′30 E. The objective of the current research work was to interpret the subsurface structure and reservoir characteristics of the Kabirwala area Tola (01) well, which is located in the Punjab platform, Central Indus Basin, utilizing 2D seismic and well log data. Formation evaluation for hydrocarbon potential using the reservoir properties is performed in this study. For the marked zone of interest, the study also focuses on evaluating the average water saturation, average total porosity, average effective porosity, and net pay thickness. The results of the study show a spotted horizon stone with respect to time and depth as follows: Dunghan formation, 0.9 s and 1080.46 m; Cretaceous Samana Suk formation, 0.96 s and 1174.05 m; Datta formation, 1.08 s and 1400 m; and Warcha formation, 1.24 s and 1810 m. Based on the interpretation of well logs, the purpose of petrophysical analysis was to identify hydrocarbon-bearing zones in the study area. Gamma ray, spontaneous potential, resistivity, neutron, and density log data were utilized. The high zone present in the east–west part of the contour maps may be a possible location of hydrocarbon entrapment, which is further confirmed by the presence of the Tola-01 well.

Sign in / Sign up

Export Citation Format

Share Document