scholarly journals Shale volume and permeability of the Miocene unconsolidated turbidite sands of Bonga oil field, Niger delta, Nigeria

2017 ◽  
Vol 5 (1) ◽  
pp. 37 ◽  
Author(s):  
Inyang Namdie ◽  
Idara Akpabio ◽  
Agbasi Okechukwu .E.
Keyword(s):  
Niger Delta ◽  
Gamma Ray ◽  
Water Saturation ◽  
Strong Dependence ◽  
Water Injection ◽  
Oil Field ◽  
Reservoir Properties ◽  
Injection Wells ◽  
Log Data ◽  
Shale Volume

Bonga oil field is located 120km (75mi) southeast of the Niger Delta, Nigeria. It is a subsea type development located about 3500ft water depth and has produced over 330 mmstb of hydrocarbon till date with over 16 oil producing and water injection wells. The producing formation is the Middle to Late Miocene unconsolidated turbidite sandstones with lateral and vertical homogeneities in reservoir properties. This work, analysis the petrophysical properties of the reservoir units for the purpose of modeling the effect of shale content on permeability in the reservoir. Turbidite sandstones are identified by gamma-ray log signatures as intervals with 26-50 API, while sonic, neutron, resistivity, caliper and other log data are applied to estimate volume of shale ranging between 0.972 v/v for shale intervals and 0.0549 v/v for turbidite sands, water saturation of 0.34 v/v average in most sand intervals, porosity range from 0.010 for shale intervals to 0.49 v/v for clean sands and permeability values for the send interval 11.46 to2634mD, for intervals between 7100 to 9100 ft., Data were analyzed using the Interactive Petrophysical software that splits the whole curve into sand and shale zones and estimates among other petrophysical parameters the shale contents of the prospective zones. While Seismic data revealed reservoir thickness ranging from 25ft to over 140ft well log data within the five wells have identified sands of similar thickness and estimated average permeability of700mD. Within the sand units across the five wells, cross plots of estimated porosity, volume of shale and permeability values reveal strong dependence of permeability on shale volume and a general decrease in permeability in intervals with shale volume. It is concluded that sand units with high shale contents that are from0.500 to0.900v/v will not provide good quality reservoir in the field.

scholarly journals Prospect evaluation and hydrocarbon potential assessment: the Lower Eocene Facha non-clastic reservoirs, Hakim Oil Field (NC74A), Sirte basin, Libya—a case study

2019 ◽  
Vol 10 (2) ◽  
pp. 351-362 ◽  
Author(s):  
Mohamed A. Kassab ◽  
Ali El-Said Abbas ◽  
Mostafa A. Teama ◽  
Musa A. S. Khalifa
Keyword(s):  
Gamma Ray ◽  
Water Saturation ◽  
Oil Field ◽  
Thickness Variation ◽  
Oil Accumulation ◽  
Lower Eocene ◽  
Log Data ◽  
Shale Volume ◽  
Volume Porosity ◽  
Sirte Basin

Abstract Petrophysical assessment of Facha Formation based on log data of six wells A1, A3, A4, A5, A8 and A13 recorded over the entire reservoir interval was established. Hakim Oil Field produces from the Lower Eocene Facha reservoir, which is located at the western side of Sirte basin. Limestone, dolostone and dolomitic limestone are the main lithologies of the Facha reservoir. This lithology is defined by neutron porosity—density cross-plot. Noteworthily, limestone increases in the lowermost intervals of the reservoir. Structurally, the field is traversed by three northwest–southeast faults. The shale of the Upper Cretaceous Sirte Formation is thought to be the source rock of the Facha Formation, whereas the seals are the limestone and anhydrite of the Lower Eocene Gir Formation. In this study, the Facha reservoir’s cutoff values were obtained from the cross-plots of the calculated shale volume, porosity and water saturation values accompanied with gamma ray log data and were set as 20%, 10% and 70%, respectively. Isoparametric maps for the thickness variation of net pay, average porosity, shale volume and water saturation were prepared, and the authors found out that the Facha Formation has promising reservoir characteristics in the area of study; a prospective region for oil accumulation trends is in the north and south of the study area.

scholarly journals Shale volume and porosity delineation of coast swamp depobelt in Niger delta region, Nigeria, using well log

2019 ◽  
Vol 7 (2) ◽  
pp. 142
Author(s):  
Ubong Essien
Keyword(s):  
Niger Delta ◽  
Gamma Ray ◽  
Water Saturation ◽  
Effective Porosity ◽  
Neutron Density ◽  
Well Log ◽  
Shale Formations ◽  
Log Data ◽  
Shale Volume ◽  
Niger Delta Region

Well log data from two wells were evaluated for shale volume, total and effective porosity. Well log data were obtained from gamma ray, neutron-density log, resistivity, sonic and caliper log respectively. This study aimed at evaluating the effect of shale volume, total and effective porosity form two well log data. The results of the analysis depict the presence of sand, sand-shale and shale formations. Hydrocarbon accumulation were found to be high in sand, fair in sand-shale and low in shale, since existence of shale reduces total and effective porosity and water saturation of the reservoir. The thickness of the reservoir ranged from 66 – 248.5ft. The average values of volume of shale, total and effective porosity values ranged from 0.004 – 0.299dec, 0.178 – 0.207dec and 0.154 – 0.194dec. Similarly, the water saturation and permeability ranged from 0.277 – 0.447dec and 36.637 - 7808.519md respectively. These values of total and effective porosity are high in sand, fair in sand-shale and low in shale formations. The results for this study demonstrate: accuracy, applicability of these approaches and enhance the proper evaluation of petrophysical parameters from well log data.    

scholarly journals Petrophysical Properties of Nahr Umar Formation in Nasiriya Oil Field

2020 ◽  
Vol 21 (3) ◽  
pp. 9-18
Author(s):  
Ahmed Abdulwahhab Suhail ◽  
Mohammed H. Hafiz ◽  
Fadhil S. Kadhim
Keyword(s):  
Gamma Ray ◽  
Water Saturation ◽  
Oil Field ◽  
Well Logs ◽  
High Porosity ◽  
Reservoir Properties ◽  
Petrophysical Parameters ◽  
Resistivity Logs ◽  
Lithology Prediction ◽  
Porosity And Permeability

   Petrophysical characterization is the most important stage in reservoir management. The main purpose of this study is to evaluate reservoir properties and lithological identification of Nahr Umar Formation in Nasiriya oil field. The available well logs are (sonic, density, neutron, gamma-ray, SP, and resistivity logs). The petrophysical parameters such as the volume of clay, porosity, permeability, water saturation, were computed and interpreted using IP4.4 software. The lithology prediction of Nahr Umar formation was carried out by sonic -density cross plot technique. Nahr Umar Formation was divided into five units based on well logs interpretation and petrophysical Analysis: Nu-1 to Nu-5. The formation lithology is mainly composed of sandstone interlaminated with shale according to the interpretation of density, sonic, and gamma-ray logs. Interpretation of formation lithology and petrophysical parameters shows that Nu-1 is characterized by low shale content with high porosity and low water saturation whereas Nu-2 and Nu-4 consist mainly of high laminated shale with low porosity and permeability. Nu-3 is high porosity and water saturation and Nu-5 consists mainly of limestone layer that represents the water zone.

scholarly journals Hydrocarbon reservoir characterization of “Otan-Ile” field, Niger Delta

2021 ◽  
Vol 11 (2) ◽  
pp. 601-615
Author(s):  
Tokunbo Sanmi Fagbemigun ◽  
Michael Ayu Ayuk ◽  
Olufemi Enitan Oyanameh ◽  
Opeyemi Joshua Akinrinade ◽  
Joel Olayide Amosun ◽  
...  
Keyword(s):  
Niger Delta ◽  
Reservoir Characterization ◽  
Water Saturation ◽  
Structural Deformation ◽  
Well Log ◽  
Reservoir Properties ◽  
Good Tool ◽  
Log Data ◽  
Hydrocarbon Reservoir ◽  
Hydrocarbon Saturation

AbstractOtan-Ile field, located in the transition zone Niger Delta, is characterized by complex structural deformation and faulting which lead to high uncertainties of reservoir properties. These high uncertainties greatly affect the exploration and development of the Otan-Ile field, and thus require proper characterization. Reservoir characterization requires integration of different data such as seismic and well log data, which are used to develop proper reservoir model. Therefore, the objective of this study is to characterize the reservoir sand bodies across the Otan-Ile field and to evaluate the petrophysical parameters using 3-dimension seismic and well log data from four wells. Reservoir sands were delineated using combination of resistivity and gamma ray logs. The estimation of reservoir properties, such as gross thickness, net thickness, volume of shale, porosity, water saturation and hydrocarbon saturation, were done using standard equations. Two horizons (T and U) as well as major and minor faults were mapped across the ‘Otan-Ile’ field. The results show that the average net thickness, volume of shale, porosity, hydrocarbon saturation and permeability across the field are 28.19 m, 15%, 37%, 71% and 26,740.24 md respectively. Two major faults (F1 and F5) dipping in northeastern and northwestern direction were identified. The horizons were characterized by structural closures which can accommodate hydrocarbon were identified. Amplitude maps superimposed on depth-structure map also validate the hydrocarbon potential of the closures on it. This study shows that the integration of 3D seismic and well log data with seismic attribute is a good tool for proper hydrocarbon reservoir characterization.

scholarly journals Seismic Data Interpretation and Petrophysical Analysis of Kabirwala Area Tola (01) Well, Central Indus Basin, Pakistan

2021 ◽  
Vol 11 (7) ◽  
pp. 2911
Author(s):  
Naveed Ahmad ◽  
Sikandar Khan ◽  
Abdullatif Al-Shuhail
Keyword(s):  
Gamma Ray ◽  
Water Saturation ◽  
Research Work ◽  
Total Porosity ◽  
Effective Porosity ◽  
Indus Basin ◽  
Drilling Process ◽  
Reservoir Properties ◽  
Log Data ◽  
Petrophysical Analysis

Well logging is a significant procedure that assists geophysicists and geologists with making predictions regarding boreholes and efficiently utilizing and optimizing the drilling process. The current study area is positioned in the Punjab Territory of Pakistan, and the geographic coordinates are 30020′10 N and 70043′30 E. The objective of the current research work was to interpret the subsurface structure and reservoir characteristics of the Kabirwala area Tola (01) well, which is located in the Punjab platform, Central Indus Basin, utilizing 2D seismic and well log data. Formation evaluation for hydrocarbon potential using the reservoir properties is performed in this study. For the marked zone of interest, the study also focuses on evaluating the average water saturation, average total porosity, average effective porosity, and net pay thickness. The results of the study show a spotted horizon stone with respect to time and depth as follows: Dunghan formation, 0.9 s and 1080.46 m; Cretaceous Samana Suk formation, 0.96 s and 1174.05 m; Datta formation, 1.08 s and 1400 m; and Warcha formation, 1.24 s and 1810 m. Based on the interpretation of well logs, the purpose of petrophysical analysis was to identify hydrocarbon-bearing zones in the study area. Gamma ray, spontaneous potential, resistivity, neutron, and density log data were utilized. The high zone present in the east–west part of the contour maps may be a possible location of hydrocarbon entrapment, which is further confirmed by the presence of the Tola-01 well.

scholarly journals Reservoir units of Mishrif Formation in Majnoon Oil field, Southern Iraq

2019 ◽  
pp. 2656-2663
Author(s):  
Layla khudhur Abbas ◽  
Thamar Abdullah Mahdi
Keyword(s):  
Gamma Ray ◽  
Water Saturation ◽  
High Volume ◽  
Effective Porosity ◽  
Oil Field ◽  
Reservoir Properties ◽  
Marine Facies ◽  
Wireline Logs ◽  
Low Volume ◽  
Southern Iraq

The reservoir units of Mishrif Formation in Majnoon oil field were studied by using available wireline logs (gamma ray, porosity and resistivity) and facies that derived from core and cutting samples for three wells including Mj-1, Mj-15, and Mj-20. The reservoir properties were determined and interpreted by using IP software. The results showed that unit D have the best reservoir properties due to high effective porosity, low water saturation and very low volume of shale. Furthermore, a large part of this unit was deposited in shoal environment. The other reservoir units are then graded in reservoir properties including units B, A, F & E respectively, except unit C, which is considered as a cap unit, because it consists of restricted marine facies so that; it has high volume of shale and water saturation and very low effective porosity.

scholarly journals The Use of Gamma Ray Log Data to Compute and Study the Deposition of Shale Volume of Mishrif Formation in Middle and Southern Parts of Iraq

2021 ◽  
pp. 3932-3941
Author(s):  
Hiba Tarq Jaleel ◽  
Ahmed S. Al-Banna ◽  
Ghazi H. Al-Sharaa
Keyword(s):  
Gamma Ray ◽  
Oil Field ◽  
Log Data ◽  
Shale Volume ◽  
Carbonate Formation ◽  
Regional Area ◽  
Isopach Map ◽  
Gamma Ray Log ◽  
Surfer Software

The shale volume is one of the most important properties that can be computed depending on gamma ray log. The shale volume of Mishrif Formation (carbonate formation from middle Cenomanian- early Turonian) was studied for the regional area of the middle and southern parts of Iraq. The gamma ray log data from seventeen  wells ( Kf-3,Kf-4, Ad-1,Ad -2,Dh-1, Bu-47, Ns-2, Ns-4, Am-1,Am-2,Hf-2,Hf-115,Mj-3,Mj-15, Su-7,Wq-15 and  Lu-7) distributed in the study area were used to compute the shale volume of Mishrif Formation. From the available data of the considered wells, a regional isopach map of Mishrif Formation was obtained. The isopach map indicates that the maximum thickness of Mishrif Formation is located at the eastern part of the study area. The results of the CPI and the shale volume map, which were computed using the Techlog and surfer software,  show that the maximum value of shale volume is located at the southern part of the study area (Su-7  well), while the minimum value is at the eastern  part (Hf-2well). According to the classification of Kamel and Mabrouk (2003), Mishrif Formation seems to be a Shaly Formation in the study area, except Halfaya oil field at the eastern part of the study area, which seems as a Clear Formation. The top map of the shale marker bed, which appears in most studied wells, shows a regional trend of the formation toward the northeast. According to the variation of the thickness of the shale marker bed, the study area is divided into four zones.

scholarly journals Evaluation of Petrophysical Properties Using Well Logs of Yamama Formation in Abu Amood Oil Field, Southern Iraq

2021 ◽  
Vol 54 (1E) ◽  
pp. 67-77
Author(s):  
Buraq Adnan Al-Baldawi
Keyword(s):  
Gamma Ray ◽  
Water Saturation ◽  
Bulk Water ◽  
Carbonate Reservoir ◽  
Oil Field ◽  
Well Logs ◽  
Water Volume ◽  
High Porosity ◽  
Petrophysical Properties ◽  
Reservoir Properties

The petrophysical analysis is very important to understand the factors controlling the reservoir quality and production wells. In the current study, the petrophysical evaluation was accomplished to hydrocarbon assessment based on well log data of four wells of Early Cretaceous carbonate reservoir Yamama Formation in Abu-Amood oil field in the southern part of Iraq. The available well logs such as sonic, density, neutron, gamma ray, SP, and resistivity logs for wells AAm-1, AAm-2, AAm-3, and AAm-5 were used to delineate the reservoir characteristics of the Yamama Formation. Lithologic and mineralogic studies were performed using porosity logs combination cross plots such as density vs. neutron cross plot and M-N mineralogy plot. These cross plots show that the Yamama Formation consists mainly of limestone and the essential mineral components are dominantly calcite with small amounts of dolomite. The petrophysical characteristics such as porosity, water and hydrocarbon saturation and bulk water volume were determined and interpreted using Techlog software to carried out and building the full computer processed interpretation for reservoir properties. Based on the petrophysical properties of studied wells, the Yamama Formation is divided into six units; (YB-1, YB-2, YB-3, YC-1, YC-2 and YC-3) separated by dense non porous units (Barrier beds). The units (YB-1, YB-2, YC-2 and YC-3) represent the most important reservoir units and oil-bearing zones because these reservoir units are characterized by good petrophysical properties due to high porosity and low to moderate water saturation. The other units are not reservoirs and not oil-bearing units due to low porosity and high-water saturation.

scholarly journals Evaluation of shale volume and effective porosity using larionov and archie equations from wire-line logs, Niger delta Nigeria

2019 ◽  
Vol 8 (4) ◽  
pp. 257
Author(s):  
Mfoniso U. Aka ◽  
Johnson Cletus Ibuot ◽  
Francisca N. Okeke
Keyword(s):  
Niger Delta ◽  
Water Saturation ◽  
Effective Porosity ◽  
Well Log ◽  
Reservoir Properties ◽  
Shale Formations ◽  
Shale Volume ◽  
Niger Delta Region ◽  
Rock Formations ◽  
Water Resistivity

<p>In Niger Delta region of Nigeria, reservoirs are mostly loose and unstratified sands to hold fluids. In this paper, three different wells in central Niger Delta were assessed for shale volume and actual porosity. The results of the analysis delineate the presence of sand, sand-shale and shale formations. Hydrocarbon prospecting was found to be strong in sand, moderate in sandshale and shallow in shale respectively. However, existent of shale lessens effective porosity and water saturation of the rock formations. The extent of the formation extends from 1300 to 2500 m. Shale volume and actual porosity values extend from 0.00 to 0.302 dec and 0.047 to 0.302 dec which decrease with increasing depth. Comparably, the water saturation and water resistivity extend from 0.432 to 0.779 dec and 0.106 to 2.918 Ohm respectively. These values of actual porosity are strong in sand, moderate in sand-shale and shallow in shale formations. The results from this assessment proof well log a vital and easier tool in assessing of reservoir properties.</p>

scholarly journals Lithology and Fluid discrimination of Sody field of the Nigerian Delta

2020 ◽  
Vol 24 (8) ◽  
pp. 1321-1327
Author(s):  
S.C.P. Finecountry ◽  
S. Inichinbia
Keyword(s):  
Niger Delta ◽  
Gamma Ray ◽  
Water Saturation ◽  
Total Porosity ◽  
Reservoir Properties ◽  
High Hydrocarbon ◽  
Average Porosity ◽  
Reservoir Porosity ◽  
Shaly Sand ◽  
Net To Gross

The lithology and fluid discrimination of an onshore Sody field, of the Niger Delta was studied using gamma ray, resistivity and density logs from  three wells in the field in order to evaluate the field’s reservoir properties. Two reservoir sands (RES 1 and RES 2) were delineated and identified as hydrocarbon bearing reservoirs. The petrophysical parameters calculated include total porosity, water saturation and volume of shale. The results obtained revealed that the average porosity of the reservoir sands, range from 21% to 39%, which is excellent indicator of a good quality reservoir and probably reflecting well sorted coarse grain sandstone reservoirs with minimal cementation. Water saturation is low in all the reservoirs, ranging from 2% to 32%, indicating that the proportion of void spaces occupied by water is low, and implying high hydrocarbon saturation. The crossplot discriminated the reservoirs lithologies as sand, shaly sand and shale sequences, except well Sody 2 which differentiated its lithologies as sand and shale sequences and distinguished the reservoirs’ litho-fluids into three, namely; gas, oil and brine. These results suggest that the reservoirs sand units of Sody field contain significant accumulations of hydrocarbon. Keywords: Reservoir, porosity, net-to-gross, impedance, lithology

Sign in / Sign up

Export Citation Format

Share Document