Kinetic Study on Delignification of Kraft-AQ Pine Pulp with Hydrogen Peroxide Catalyzed by Mn(IV)-Me4DTNE

Holzforschung ◽  
2000 ◽  
Vol 54 (4) ◽  
pp. 413-419 ◽  
Author(s):  
Yu Cui ◽  
Pratuang Puthson ◽  
Chen-Loung Chen ◽  
Josef S. Gratzl ◽  
Adrianna G. Kirkman
Keyword(s):  
Hydrogen Peroxide ◽  
Initial Phase ◽  
Model Compound ◽  
Kinetic Studies ◽  
Kappa Number ◽  
Lignin Model Compound ◽  
First Order Kinetics ◽  
Residual Phase ◽  
Lignin Model ◽  
Kinetics Of

Summary The kinetics of delignification of a kraft-AQ southern pine pulp with hydrogen peroxide catalyzed by [LMn(IV)(μ-O)3Mn(IV)](ClO4)2 (1), where L = 1,2-bis(4,7-dimethyl-1,4,7-triazacyclonon-1-yl)ethane was studied. The degree of delignification was significantly improved by using the catalyst. The pulp was bleached for 2 hours at 80°C, in 10% consistency with 2% NaOH, 4% H2O2 and 60 ppm catalyst charges on pulp (O.D.). Kappa number of the pulp was reduced from 31.6 to 16.8 corresponding to a degree of delignification of approximately 4%, while GE brightness was increased from 24.2 to 44.7. At the same time, viscosity of the resulting pulp was reduced from 31.1 mPa•s to 20.1 mPa•s compared to the reduction from 31.1 mPa•s to 20.1 mPa•s in the uncatalyzed bleaching under the same reaction condition. This indicates that the degradation of the carbohydrates was moderate in the catalyzed bleaching compared to the uncatalyzed bleaching. The delignification was found to follow pseudo first order kinetics with respect to kappa number, i.e., residual lignin, in the initial phase and quickly slowed down after 30 minutes (residual phase) under all the reaction temperatures investigated. The delignification rate constants in the initial phase were 0.17, 0.18, and 0.21 min−1 at 50, 60, and 80°C, respectively. Degree of delignification at the delignification time of 30 minutes is approximately 40% at 80°C. The possible delignification mechanism was discussed on the basis of the kinetic studies and lignin model compound experiments.

Reaction kinetics of strong nucleophiles with a dimeric non-phenolic lignin model compound with α-carbonyl functionality (adleron) in aqueous alkali solution

Holzforschung ◽  
2016 ◽  
Vol 70 (9) ◽  
pp. 811-818 ◽  
Author(s):  
Olesya Fearon ◽  
Susanna Kuitunen ◽  
Tapani Vuorinen
Keyword(s):  
Hydrogen Sulfide ◽  
Model Compound ◽  
Degradation Kinetics ◽  
Reaction Products ◽  
Lignin Model Compound ◽  
Vis Spectroscopy ◽  
Soda Pulping ◽  
Lignin Model ◽  
Kinetics Of ◽  
Sulfite Ion

Abstract The degradation kinetics of a non-phenolic lignin model compound with α-carbonyl functionality (adlerone) has been studied by varying temperature and concentrations of sodium hydroxide, sodium hydrogen sulfide, and sodium sulfite. The kinetics of adlerone degradation and formation of its reaction products were monitored by UV-Vis spectroscopy and their structures were analyzed by GC/MS. The two step degradation of adlerone was studied in two separate experimental setups. In the first alkali catalyzed step, adlerone is converted to a β-elimination product that reacts further in the second step with hydrogen sulfide or sulfite ion. The Arrhenius kinetic parameters were derived by the KinFit software. The activation energy for the 1st step was 69.1 kJ mol-1, and for the 2nd step with sulfide 42.4 kJ mol-1 and with sulfite ion 35.8 kJ mol-1. The reaction mechanisms presented are in line with those published earlier: β-ether bonds of structures having α-carbonyl functionality do not cleave under soda pulping conditions, whereas in kraft and sulfite pulping the cleavage of β-ether bonds proceeds via nucleophile attack and addition. The combination of hydroxyl and sulfite ions gives the fastest cleavage of β-ether bonds in non-phenolic lignin structures with the α-carbonyl functionality.

Kinetics of the reaction between a lignin model compound and chlorine dioxide

2020 ◽  
Vol 393 ◽  
pp. 124783
Author(s):  
Ming Lei ◽  
Bin Luo ◽  
Qingtong Zhang ◽  
Chenyan Guo ◽  
Mingchao Chi ◽  
...  
Keyword(s):  
Chlorine Dioxide ◽  
Model Compound ◽  
Lignin Model Compound ◽  
Lignin Model ◽  
Kinetics Of

scholarly journals KINETICS OF OXIDATION WITH HYDROGEN PEROXIDE AND IRON(II) COMPLEX WITH A MACROCYCLIC BINUCLEATING LIGAND

1995 ◽  
Vol 3 (3) ◽  
pp. 55-62
Author(s):  
Lourdes T. Kist ◽  
Bruno Szpoganicz ◽  
Manuel G. Basallote ◽  
Maria J. F. Trujillo ◽  
Maria A. Mariez
Keyword(s):  
Hydrogen Peroxide ◽  
Macrocyclic Ligand ◽  
Kinetic Studies ◽  
Organic Substrates ◽  
Kinetics Of Oxidation ◽  
Oxidation Processes ◽  
First Order ◽  
First Order Kinetics ◽  
Kinetics Of ◽  
Catalyzed Oxidation

In the present study solutions of a complex of Fe(II) with a macrocyclic ligand were prepared and their oxidation kinetics with hydrogen peroxide examined. The kinetic studies of the oxidation processes lead to values of rate constant of two-step which occur via first-order kinetics. The results are expected to result in a better knowledge of the mechanism of H202 activation in catalyzed oxidation of organic substrates.

scholarly journals Revisiting the mechanism of β-O-4 bond cleavage during acidolysis of lignin VII: acidolyses of non-phenolic C6-C2-type model compounds using HBr, HCl and H2SO4, and a proposal on the characteristic action of Br− and Cl−

2020 ◽  
Vol 66 (1) ◽  
Author(s):  
Qiaoqiao Ye ◽  
Tomoya Yokoyama
Keyword(s):  
Model Compound ◽  
Bond Cleavage ◽  
Type Model ◽  
Enol Ether ◽  
Lignin Model Compound ◽  
Benzyl Cation ◽  
Acid Type ◽  
Unstable Compound ◽  
Lignin Model ◽  
Acidolysis Reaction

AbstractA non-phenolic C6-C2-type lignin model compound with the β-O-4 bond, 2-(2-methoxyphenoxy)-1-(3,4-dimethoxyphenyl)ethanol (I), was acidolyzed in aqueous 82% 1,4-dioxane containing HBr, HCl, or H2SO4 with a concentration of 0.2 mol/L at 85 ℃ to examine the differences between these acidolyses. Compound I primarily converted to an enol ether compound, 1-(2-methoxyphenoxy)-2-(3,4-dimethoxyphenyl)ethene (II), via the benzyl cation followed by acidolytic β-O-4 bond cleavage regardless of the acid-type, although the disappearance rates of compound I were remarkably different (HBr > HCl >> H2SO4). Acidolyses of compound II using these acids under the same conditions showed a similar tendency, but the rate differences were much smaller than in the acidolyses of compound I. Acidolyses of the α-methyl-etherified derivative of compound I (I-α-OMe) using these acids under the same conditions suggested that the formation rates of the benzyl cation from compound I-α-OMe (also from compound I) are not largely different between the acidolyses using these acids, but those of compound II from the benzyl cation are remarkably different. Acidolysis of the α-bromo-substituting derivative of compound I (I-α-Br) using HBr under the same conditions showed a characteristic action of Br¯ in the acidolysis. Br¯ adds to the benzyl cation generated from compound I or I-α-OMe to afford unstable compound I-α-Br, resulting in acceleration of the formation of compound II and of the whole acidolysis reaction.

scholarly journals Model compounds-based study on adsorption and dispersion properties of lignin-based superplasticizer

2021 ◽  
Vol 104 (1) ◽  
pp. 003685042098062
Author(s):  
Shuangping Ma ◽  
Qingjun Ding ◽  
Fen Zhou ◽  
Huaxiong Zhu
Keyword(s):  
Molecular Structure ◽  
Zeta Potential ◽  
Model Compound ◽  
Research Work ◽  
Structure Activity Relationship ◽  
Activity Relationship ◽  
Lignin Model Compound ◽  
Structure Activity ◽  
Lignin Model ◽  
Relationship Of

The chemical modifications of lignin-based superplasticizers have attracted extensive attentions during recent years. The comprehending of the structure-activity relationship of lignin-based superplasticizer is important to promote the modification and application research of lignin resources. However, lignin features complex and variable molecular structure, which is not conducive to study on structure-activity relationship of lignin-based superplasticizer as well as development and application of new lignin-based superplasticizer. However, the related research work can be simplified by selecting small molecular compound with appropriate molecular structure as the lignin model compound. This article intends to study the structure-activity relationship of lignin-based superplasticizer by using dihydroeugenol as the lignin model compound. Through the substitution of lignin by dihydroeugenol during the synthesis process, a model compound lignin-based superplasticizer (DAFS) was synthesized. The adsorption and dispersion properties of this superplasticizer and reference sample (LAFS) were investigated by fluidity test, Zeta-potential measurement, Total organic carbon analysis and others. The results suggest that the adsorption behavior of both DAFS and LAFS conformed to the Langmuir isotherms and Pseudo-second order kinetic. In cement paste, added with 1 g/L of LAFS and DAFS, Zeta potential were reduced from +3.5 to −15.2 mV and −18.7 mV, respectively. The substitution of lignin by dihydroeugenol has no significantly influence on the dispersive property, but differences on rheological properties which need to be optimized in the future. All the tests confirmed that dihydroeugenol is suitable to replace lignin on exploring the structure-activity relationship of lignin-based superplasticizer. This research work provides new insight on model study of lignin-based superplasticizer.

Synthesis and application of Co(salen) complexes containing proximal imidazolium ionic liquid cores

2012 ◽  
Vol 90 (1) ◽  
pp. 60-70 ◽  
Author(s):  
Swapnil Sonar ◽  
Kenson Ambrose ◽  
Arthur D. Hendsbee ◽  
Jason D. Masuda ◽  
Robert D. Singer
Keyword(s):  
Ionic Liquid ◽  
Ionic Liquids ◽  
Model Compound ◽  
Veratryl Alcohol ◽  
Oxidation Catalysts ◽  
Imidazolium Ionic Liquid ◽  
Lignin Model Compound ◽  
Salen Complexes ◽  
Lignin Model ◽  
Salen Ligand

Ionic ligands derived from a salen ligand containing two proximal 1,3-disubstituted imidazolium ionic liquid cores form cobalt(III) complexes capable of selectively oxidizing veratryl alcohol, a lignin model compound, to veratraldehyde using air as the source of oxygen. These complexes are easy to prepare, inexpensive, water stable, and soluble in ionic liquids, making them viable candidates for use as oxidation catalysts.

Sign in / Sign up

Export Citation Format

Share Document