Vibration method for grading of large cross-section coniferous timber species

Holzforschung ◽  
2012 ◽  
Vol 66 (3) ◽  
Author(s):  
Francisco Arriaga ◽  
Guillermo Íñiguez-González ◽  
Miguel Esteban ◽  
Ferenc Divos
Keyword(s):  
Natural Frequency ◽  
Modulus Of Elasticity ◽  
Dynamic Modulus ◽  
Longitudinal Vibration ◽  
Strong Relationship ◽  
Modulus Of Rupture ◽  
Bending Test ◽  
Timber Species ◽  
Vibration Method ◽  
Dynamic Modulus Of Elasticity

Abstract The non-destructive testing (NDT) of timber using the longitudinal vibration method is based on the natural frequency of wood which is in relation to its quality. In the present paper, the suitability of this tool is investigated and the results of grading 395 pieces are presented. Structural timber of Radiata pine (Pinus radiata D. Don.), Scots pine (Pinus sylvestris L.), and Laricio pine [Pinus nigra ssp. salzmannii (Dunal) Franco] from Spanish sources were investigated. The specimens were tested for bending according to the European standard EN 408 (2003) and the values of strength and stiffness were compared with the results estimated by means of NDT. The vibration equipment applied permits the measurement of the longitudinal natural frequency and mass of the specimen, and then the density and the dynamic modulus of elasticity can be calculated. There is a strong relationship between the static modulus of elasticity obtained from the bending test and the dynamic modulus of elasticity obtained by the NDT technique. There is an acceptable relationship between modulus of rupture and dynamic modulus of elasticity if the visual defects (knot sizes) are taken into account. Acoustic measurements have become widely acceptable, and they have great potential for stress grading of coniferous timber.

Comparative Study on Four Different Methods for Measuring the Dynamic Modulus of Elasticity of Acer Mono Wood

2010 ◽  
Vol 160-162 ◽  
pp. 384-388
Author(s):  
Hua Dong Xu ◽  
Li Hai Wang
Keyword(s):  
Modulus Of Elasticity ◽  
Dynamic Modulus ◽  
Bending Test ◽  
Linear Regression Method ◽  
Clear Wood ◽  
Vibration Method ◽  
Dynamic Modulus Of Elasticity ◽  
The Mean ◽  
The Difference ◽  
Acer Mono

The dynamic modulus of elasticity (MOE) of forty one small Acer mono clear wood specimens was tested via stress wave, ultrasonic wave, edgewise vibration and flatwise vibration method respectively in laboratory. Then the static MOE of these specimens was measured with static bending test. The correlations between dynamic and static MOE were analyzed using linear regression method, and the difference of various methods was discussed using paired t test. The results show that the dynamic MOE of wood measured by four methods described above are higher than the static MOE, but their linear correlation is significantly strong. Thus, it is feasible to estimate static MOE using these four methods. Additionally, the mean of paired difference between static MOE and dynamic MOE tested by flatwise vibration method is least, and the correlation highest. Therefore, it is better to use flatwise vibration method to estimate static MOE of wood.

Relativity Analysis between Dynamic and Static Modulus of Elasticity on Different Thickness Wood-Plastic Structural Plates

2011 ◽  
Vol 121-126 ◽  
pp. 4254-4258 ◽  
Author(s):  
Gui Wen Yu ◽  
Ying Cheng Hu ◽  
Ji You Gu
Keyword(s):  
Mechanical Properties ◽  
Nondestructive Testing ◽  
Modulus Of Elasticity ◽  
Dynamic Modulus ◽  
Bending Test ◽  
Three Point Bending ◽  
Static Modulus ◽  
Dynamic Modulus Of Elasticity ◽  
Static Modulus Of Elasticity ◽  
Different Thickness

The relativity was evaluated between dynamic modulus of elasticity (MOE) and static MOE, in order to assess the potential of using nondestructive testing (NDT) method as a checking tool for mechanical properties of wood-plastic structural plates. The dynamic MOE was evaluated on a FFT system, and the static MOE was determined by three point bending test. All of specimens were made of polyethylene（PE）and poplar flour. A significant correlation between the dynamic MOE and the static MOE was obtained from relativity analysis. These results suggest that the NDT method could be appropriate to estimate the dynamic MOE of specimens with different thickness.

scholarly journals Prediction of Mechanical Properties of Hardwood Species Using the Longitudinal Vibration Acoustic Method

2021 ◽  
Vol 71 (4) ◽  
pp. 391-400
Author(s):  
Kayode Olaoye ◽  
Lawrence Aguda ◽  
Bolade Ogunleye
Keyword(s):  
Mechanical Properties ◽  
Modulus Of Elasticity ◽  
Dynamic Modulus ◽  
Longitudinal Vibration ◽  
Modulus Of Rupture ◽  
Damping Factor ◽  
Acoustic Parameters ◽  
Static Modulus ◽  
Hardwood Species ◽  
Static Modulus Of Elasticity

Abstract Acoustic test methods such as longitudinal vibration have been developed to predict the elastic properties of wood. However, attention has not been shifted to using this method to predict other mechanical properties, especially on Nigeria's preferred, and lesser-used wood species. Thus, we further investigate relationships among mechanical and acoustic properties of selected hardwood species with a view of predicting the mechanical properties of wood from acoustic parameters. Clear wood samples (324) of 20 by 20 by 20 mm3 were collected axially from Albizia adianthifolia, Gmelina arborea, Delonix regia, and Boscia anguistifolia trees, and conditioned before testing. The longitudinal vibration method was adopted to test for the dynamic (acoustic) parameters and properties (fundamental frequency, damping factor, dynamic modulus of elasticity, sound velocity, specific elastic modulus, radiation coefficient, acoustic conversion efficiency, acoustic impedance) while the universal testing machine was used to test for the mechanical properties (static modulus of elasticity, modulus of rupture, maximum compression strength parallel to grain). The damping factor, dynamic modulus of elasticity, and acoustic impedance were the best acoustic parameters that significantly correlated with the static modulus of elasticity (−0.57, 0.81, 0.76), modulus of rupture −0.64, 0.82, 0.85) and maximum compression strength parallel to grain (−0.52, 0.78, 0.84), respectively. There was a significant difference in the mechanical properties with respect to species, thus A. adianthifolia and G. arborea were mechanically better than D. regia and B. anguistifolia for construction or structural purposes. This study revealed that additional new acoustic measures are suitable for inferring mechanical wood properties.

ANALYSIS OF SOUND SPEED IN LONGITUDINAL DIRECTION AT REFERENCE MOISTURE CONTENT (w = 12 %) IN SAWMILL ASSORTMENTS (FAGUS SYLVATICA, L.)

Akustika ◽  
2020 ◽  
pp. 45-50
Author(s):  
Alena Rohanová
Keyword(s):  
Moisture Content ◽  
Modulus Of Elasticity ◽  
Dynamic Modulus ◽  
Sound Speed ◽  
Longitudinal Direction ◽  
Structural Timber ◽  
Sound Speeds ◽  
Dynamic Modulus Of Elasticity ◽  
Round Timber

This paper explores the analysis of sound speeds in the longitudinal direction and their reduction to the reference moisture content w = 12 %. The sound speed cw was determined with Sylvatest Duo device. Moisture content of beech sawmill assortments (round timber: N = 16, logs: N = 2 × 16, structural boards: N = 54) in the range of 12 – 72 % was measured. For the analysis purposes, the sound speed was converted to reference conditions (c12, uref = 12%). A second-degree polynomial (parabola) with a regression equation of the form: c// = 5649 - 27,371 × w + 0.0735 × w2 was used to convert cw to c12, and correction of measured and calculated values was used as well. The sound speeds c12 in sawmill assortments (c12,round, c12,log, c12,board) were evaluated by linear dependences. Dependence was not confirmed for c12,round and c12,board1 (r = 0.168), in contrast for c12,round and c12,log2 the dependence is statistically very significant (r = 0.634). The results of testing showed that the most suitable procedure for predicting quality of structural timber is the first step round timber – log2, the second step: log2 - board2. More exact results of the construction boards were obtained from log2 than from log1. The sound speed is used in the calculation of dynamic modulus of elasticity (Edyn). EN 408 mentions the possibility of using dynamic modulus of elasticity as an alternative method in predicting the quality of structural timber.

scholarly journals Diagnosis and Assessment of Deep Pile Cap Foundation of a Tall Building Affected by Internal Expansion Reactions

Buildings ◽  
2021 ◽  
Vol 11 (3) ◽  
pp. 104
Author(s):  
Fernando A. N. Silva ◽  
João M. P. Q. Delgado ◽  
António C. Azevedo ◽  
Tahlaiti Mahfoud ◽  
Abdelhafid Khelidj ◽  
...  
Keyword(s):  
Compressive Strength ◽  
Reinforced Concrete ◽  
Modulus Of Elasticity ◽  
Dynamic Modulus ◽  
Structural Integrity ◽  
Gas Permeability ◽  
Ettringite Formation ◽  
Dynamic Modulus Of Elasticity ◽  
Pile Cap ◽  
Deterioration Process

Early deterioration of reinforced concrete foundations has been often reported in recent years. This process is usually characterized by an extensive mapping cracking process on concrete surfaces that results from several types of Internal Swelling Reaction (ISR). In this paper, a real case study of a tall reinforced concrete building with a severe deterioration process installed in its deep foundations is discussed. Laboratory tests were performed in concrete drilled cores extracted from a deep pile cap block 19 years after the beginning of construction. Tests to assess the compressive strength, the static and the dynamic modulus of elasticity, the gas permeability, and electron microscopy scanning to find out the primary mechanism responsible for the deterioration observed during in situ inspections. Chemical alterations of materials were observed in concrete cores, mainly due to Delayed Ettringite Formation (DEF), which significantly affected the integrity and durability of the structure. Dynamic modulus of elasticity showed to be a better indicator of damage induced by ISR in concrete than compressive strength. Procedures to strengthen the deteriorated elements using prestressing proved to be an efficient strategy to recover the structural integrity of pile caps deteriorated due to expansions due to ISR.

scholarly journals Effects of ring characteristics on the compressive strength and dynamic modulus of elasticity of seven softwood species

Holzforschung ◽  
2007 ◽  
Vol 61 (4) ◽  
pp. 414-418 ◽  
Author(s):  
Cheng-Jung Lin ◽  
Ming-Jer Tsai ◽  
Chia-Ju Lee ◽  
Song-Yung Wang ◽  
Lang-Dong Lin
Keyword(s):  
Compressive Strength ◽  
Statistical Analysis ◽  
Modulus Of Elasticity ◽  
Dynamic Modulus ◽  
Ring Width ◽  
Ring Density ◽  
Dynamic Modulus Of Elasticity ◽  
Wave Technique ◽  
Wood Strength ◽  
Softwood Species

Abstract The effects of ring characteristics on the compressive strength and dynamic modulus of elasticity of seven softwood species in Taiwan were examined. The results revealed good correlation between compressive strength and dynamic modulus of elasticity obtained using an ultrasonic wave technique (correlation coefficient r=0.77–0.86). Overall, compressive strength increased with decreasing ring width parameters and increasing ring density parameters. Ring density was related to compressive strength, but was not the sole factor affecting the wood strength. According to our statistical analysis, compressive strength was affected by various ring characteristics. Relationships between ring characteristics and compressive strength are influenced by the anatomic direction. Results revealed that earlywood density and minimum density in a ring are equally important variables for evaluating the compressive strength of wood.

Nondestructive Evaluation of Red Oak and White Oak Species

2020 ◽  
Vol 70 (3) ◽  
pp. 370-377
Author(s):  
Cristian Grecca Turkot ◽  
Roy Daniel Seale ◽  
Edward D. Entsminger ◽  
Frederico José Nistal França ◽  
Rubin Shmulsky
Keyword(s):  
Modulus Of Elasticity ◽  
Longitudinal Vibration ◽  
Mechanical Tests ◽  
Modulus Of Rupture ◽  
Red Oak ◽  
Quercus Alba ◽  
White Oak ◽  
Static Modulus ◽  
Static Modulus Of Elasticity ◽  
The Relationship

Abstract The objective of this article is to evaluate the relationship between the dynamic modulus of elasticity (MOEd), which was obtained with acoustic-based nondestructive testing (NDT) methods, and static bending properties of two domestic hardwood oak species. The mechanical properties were conducted using static modulus of elasticity (MOE) and modulus of rupture (MOR) in radial and tangential directions. Mechanical tests were performed according to ASTM D143 on small clear, defect-free specimens from the two tree species: red oak (Quercus rubra) and white oak (Quercus alba). The MOEd was determined by two NDT methods and three longitudinal vibration methods based on the fast Fourier transform. The destructive strength values obtained in this study were within the expected range for these species. The MOE was best predicted by NDT methods for both species but also had a strong capability to predict MOR.

Sign in / Sign up

Export Citation Format

Share Document