Conjugate Heat Transfer Analysis on the Interior Surface of Nozzle Guide Vane with Combined Impingement and Film Cooling

2020 ◽  
Vol 37 (4) ◽  
pp. 327-342
Author(s):  
Arun Kumar Pujari ◽  
B. V. S. S. S Prasad ◽  
Nekkanti Sitaram
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Surface Temperature ◽  
Film Cooling ◽  
Conjugate Heat Transfer ◽  
Guide Vane ◽  
Internal Surface ◽  
Conducting Material ◽  
Nozzle Guide Vane ◽  
Nozzle Guide

AbstractThe effect of conjugate heat transfer is investigated on a first stage nozzle guide vane (NGV) of a high pressure gas turbine which has both impingement and film cooling holes. The study is carried out computationally by considering a linear cascade domain, having two passages formed between the vanes, with a chord length of 228 mm and spacing of 200 mm. The effect of (i) coolant and mainstream Reynolds numbers, (ii) thermal conductivity (iii) temperature difference between the mainstream and coolant at the internal surface of the nozzle guide vane are investigated under conjugate thermal condition. The results show that, with increasing coolant Reynolds number the lower conducting material shows larger percentage decrease in surface temperature as compared to the higher conducting material. However, the internal surface temperature is nearly independent of mainstream Reynolds number variation but shows significant variation for higher conducting material. Further, the temperature gradient within the solid thickness of NGV is higher for the lower conductivity material.

An Internal Heat Transfer Study in a Cooled Nozzle Guide Vane of a Linear Cascade

2014 ◽  
Author(s):  
Arun Kumar Pujari ◽  
Prasad B. V. S. S. Subrahmanyaa ◽  
Sitaram Nekkanti
Keyword(s):  
Heat Transfer ◽  
Surface Temperature ◽  
Film Cooling ◽  
Guide Vane ◽  
Internal Heat ◽  
Leading Edge ◽  
Internal Surface ◽  
Structure Variation ◽  
Nozzle Guide Vane ◽  
Nozzle Guide

Experimental and computational heat transfer investigations are reported in the interior mid span of the pressure surface of a Nozzle Guide Vane (NGV) subjected to combined impingement and film cooling. The study is carried out by considering a two dimensional cascade domain having four passages formed between the five vane each has a chord length of 228 mm and spacing (between the blades) of 200 mm. The vane internal surface is cooled by two impingement inserts namely front and aft impingement tubes. The front impingement tube is used to cool the internal side of the leading edge of the NGV whereas the aft impingement tube is used to cool mainly the mid span of the internal surface. The mass flow through the impingement chamber is varied for a fixed target plate distance to jet diameter ratio of 1.12. The surface temperature at the mid chord region was measured by liquid crystal technique. The surface temperature obtained from both experiments and computations are compared and the computationally obtained average heat transfer coefficient distribution along chord reported. The flow structure variation along the chord and its effect on Nusselt number distribution is presented. The computation is carried out by using Shear stress transport (SST) k-ω turbulence model in the ANSY FLUENT-14 flow solver.

CFD Study of Combined Impingement and Film Cooling Flow on the Internal Surface Temperature Distribution of a Vane

2019 ◽  
Vol 0 (0) ◽  
Author(s):  
Arun Kumar Pujari
Keyword(s):  
Reynolds Number ◽  
Surface Temperature ◽  
Film Cooling ◽  
Guide Vane ◽  
Cross Flow ◽  
Internal Surface ◽  
Flow Reynolds Number ◽  
Nozzle Guide Vane ◽  
Lift Off ◽  
Nozzle Guide

Abstract Conjugate heat transfer analysis is carried out on the internal surface of the first-stage nozzle guide vane of a gas turbine, which has both impingement and film cooling holes. The mainstream flow Reynolds number and internal coolant flow Reynolds number systematically changed and its effect on internal local surface temperature variation is studied. It is found that an increase in the coolant mass flow rate causes a non-uniform decrease in the local internal surface temperature. The external film coolant jet-lift off and internal impingement cross-flow are significant contributors to the non-uniform variation in surface temperature. It is also observed that the leading edge regions are prone to jet lift-off, whereas the tip regions of the suction surface are prone to self-induced cross-flow, due to which hot patches are formed in these regions. Hot patches are observed near the hub regions of a pressure surface due to the reduced film thickness on the external surface. From these observations it is concluded that local values of internal surface temperature are differently affected in different regions of the vane surface for a given combination of mainstream and coolant flow rates. Therefore, the conventional method of obtaining the internal temperature distributions by considering generalized geometries may not yield accurate solutions, in predicting the life of the nozzle guide vane.

Heat Transfer Studies on the Interior Surfaces of Cooled Nozzle Guide Vane in a Linear Cascade

2015 ◽  
Author(s):  
Arun Kumar Pujari ◽  
Bhamidi Prasad ◽  
Nekkanti Sitaram
Keyword(s):  
Heat Transfer ◽  
Surface Temperature ◽  
Guide Vane ◽  
Internal Heat ◽  
Leading Edge ◽  
Internal Surface ◽  
Transfer Coefficients ◽  
Computational Data ◽  
Nozzle Guide Vane ◽  
Nozzle Guide

Experimental and computational heat transfer investigations are reported in the interior side of a nozzle guide vane (NGV) subjected to combined impingement and film cooling. The domain of study is a two dimensional five-vane cascade having four passages. Each vane has a chord length of 228 mm and the pitch distance between the vanes is 200 mm. The vane internal surface is cooled by dry air supplied through the two impingement inserts: the front and the aft. The mass flow through the impingement chamber is varied, for a fixed spacing (H) to jet diameter (d) ratio of 1.2. The surface temperature distributions, at certain locations of the vane interior, are measured by pasting strips of liquid crystal sheets. The vane interior surface temperature distribution is also obtained by computations carried out by using Shear stress transport (SST) k-ω turbulence model in the ANSY FLUENT-14 flow solver. The computational data are in good agreement with the measured values of temperature. The internal heat transfer coefficients are thence determined along the leading edge and the mid span region from the computational data.

Effect of Blowing Ratio on the Internal Heat Transfer of a Cooled Nozzle Guide Vane in a Linear Cascade

2016 ◽  
Vol 8 (4) ◽  
Author(s):  
Arun Kumar Pujari ◽  
B. V. S. S. S. Prasad ◽  
Nekkanti Sitaram
Keyword(s):  
Heat Transfer ◽  
Surface Temperature ◽  
Guide Vane ◽  
Internal Heat ◽  
Internal Surface ◽  
Blowing Ratio ◽  
Computational Data ◽  
Nozzle Guide Vane ◽  
Nozzle Guide ◽  
Internal Heat Transfer

Experimental and computational heat transfer investigations are reported on the interior side of a nozzle guide vane (NGV) subjected to combined impingement and film cooling. The domain of study is a two-dimensional five-vane cascade having a space chord ratio of 0.88. The vane internal surface is cooled by dry air, supplied through the two impingement inserts: the front and the aft. The blowing ratio (ρcVc/ρmVm) is varied systematically by varying the coolant mass flow through the impingement chamber and also by changing the mainstream Reynolds number, but by keeping a fixed spacing (H) to jet diameter (d) ratio of 1.2. The surface temperature distributions, at certain locations of the vane interior surface, are measured by pasting strips of liquid crystal sheets. The vane interior surface temperature distribution is also obtained by the computations carried out by using shear stress transport (SST) k–ω turbulence model in the flow solver ansys fluent-14. The computational data are in good agreement with the measured values of temperature. The internal heat transfer coefficients are thence determined from the computational data. The results show that, when the blowing ratio is increased by increasing the coolant flow rate, the average internal surface temperature decreases. However, when the blowing ratio is varied by increasing the mainstream Reynolds number, the internal surface temperature increases. Further, the temperature variations are different all along the internal surface from the leading edge to the trailing edge and are largely dependent on the coolant flow distributions on the internal as well as the external sides.

The Influence of the Boundary Layer State and Reynolds Number on Film Cooling and Heat Transfer on a Cooled Nozzle Guide Vane

2000 ◽  
Author(s):  
Hans Reiss ◽  
Albin Bölcs
Keyword(s):  
Heat Transfer ◽  
Boundary Layer ◽  
Film Cooling ◽  
Guide Vane ◽  
Suction Side ◽  
Flow Conditions ◽  
Transfer Coefficients ◽  
Heat Transfer Coefficients ◽  
Nozzle Guide Vane ◽  
Nozzle Guide

Film cooling and heat transfer measurements were carried out on a cooled nozzle guide vane in a linear cascade, using a transient liquid crystal technique. Three flow conditions were realized: the nominal operating condition of the vane with an exit Reynolds number of 1.47e6, as well as two lower flow conditions: Re2L = 1.0e6 and 7.5e5. The vane model was equipped with a single row of inclined round film cooling holes with compound angle orientation on the suction side. Blowing ratios ranging form 0.3 to 1.5 were covered, all using foreign gas injection (CO2) yielding an engine-representative density ratio of 1.6. Two distinct states of the incoming boundary layer onto the injection station were compared, an undisturbed laminar boundary layer as it forms naturally on the suction side, and a fully turbulent boundary layer which was triggered with a trip wire upstream of injection. The aerodynamic flow field is characterized in terms of profile Mach number distribution, and the associated heat transfer coefficients around the uncooled airfoil are presented. Both detailed and spanwise averaged results of film cooling effectiveness and heat transfer coefficients are shown on the suction side, which indicate considerable influence of the state of the incoming boundary layer on the performance of a film cooling row. The influence of the mainstream flow condition on the film cooling behavior at constant blowing ratio is discussed for three chosen injection regimes.

The Effects of Slot Film Cooling on Deposition on a Nozzle Guide Vane

2014 ◽  
Author(s):  
Robin Prenter ◽  
Steven M. Whitaker ◽  
Ali Ameri ◽  
Jeffrey P. Bons
Keyword(s):  
Surface Temperature ◽  
Mass Flow ◽  
Flow Rate ◽  
Film Cooling ◽  
Guide Vane ◽  
Capture Efficiency ◽  
Coolant Flow Rate ◽  
Nozzle Guide Vane ◽  
Nozzle Guide ◽  
Slot Film Cooling

The effects of slot film cooling on deposition in a high pressure nozzle guide vane passage were investigated experimentally and computationally. Experiments were conducted in Ohio State’s Turbine Reaction Flow Rig, using a four-vane cascade, operating at temperatures up to 1353 K. Film cooling was achieved on one of the vanes using a span-wise slot, located at approximately 30% chord on the pressure surface. The coolant’s effect on vane surface temperature was characterized by taking infrared images at various cooling levels. Deposition was produced by injecting sub-bituminous ash particles with a median diameter of 6.48 μm upstream of the vane passage. Several deposition tests were conducted with varying coolant levels. Results exhibit a strong relationship between the coolant flow rate and the amount of ash that deposits on the cooled vane. Capture efficiency was reduced by 70% at the highest coolant flow rate (1.27% of the mass flow rate in the passage). Capture efficiency reduction was compared to that achieved using discrete hole film cooling in other studies. The slot scheme showed similar or larger reductions in capture efficiency at lower coolant mass flow rates. Deposit distribution patterns are affected by regions of cooler temperature, both downstream of the slot where film effects dominate, and slightly upstream of the slot which is cooled by conduction. A computational simulation was conducted to model both the flow and deposition. The solid vane was also discretized to allow for conjugate heat transfer calculations, which produced results that were qualitatively similar to IR measurements, but over predicted the effectiveness of the coolant. An Eulerian-Lagrangian particle tracking model was utilized to track the ash particles through the flow. A sticking model was implemented to determine whether particles stick upon impacting the vane surface, from which deposition rates and distributions are obtained. The computational model under predicted the baseline capture efficiency and the capture efficiency reduction factors for each cooling level, suggesting that the model is not sufficiently sensitive to the temperature changes between tests. Inclusion of surface temperature and local shear dependencies was suggested as an improvement to the sticking model.

A Converging Slot-Hole Film-Cooling Geometry—Part 2: Transonic Nozzle Guide Vane Heat Transfer and Loss

2002 ◽  
Vol 124 (3) ◽  
pp. 461-471 ◽  
Author(s):  
J. E. Sargison ◽  
S. M. Guo ◽  
M. L. G. Oldfield ◽  
G. D. Lock ◽  
A. J. Rawlinson
Keyword(s):  
Heat Transfer ◽  
Film Cooling ◽  
Guide Vane ◽  
Density Ratio ◽  
Wide Band ◽  
Nozzle Guide Vane ◽  
Cooling Hole ◽  
Hole Geometry ◽  
Temperature Levels ◽  
Nozzle Guide

This paper presents the first experimental measurements on an engine representative nozzle guide vane, of a new film-cooling hole geometry, a con¯vergings¯lot-hole¯ or console. The patented console geometry is designed to improve the heat transfer and aerodynamic performance of turbine vane and rotor blade cooling systems. These experiments follow the successful validation of the console design in low-speed flat-plate tests described in Part 1 of this paper. Stereolithography was used to manufacture a resin model of a transonic, engine representative nozzle guide vane in which seven rows of previously tested fan-shaped film-cooling holes were replaced by four rows of consoles. This vane was mounted in the annular vane ring of the Oxford cold heat transfer tunnel for testing at engine Reynolds numbers, Mach numbers and coolant to mainstream momentum flux ratios using a heavy gas to simulate the correct coolant to mainstream density ratio. Heat transfer data were measured using wide-band thermochromic liquid crystals and a modified analysis technique. Both surface heat transfer coefficient and the adiabatic cooling effectiveness were derived from computer-video records of hue changes during the transient tunnel run. The cooling performance, quantified by the heat flux at engine temperature levels, of the console vane compares favourably with that of the previously tested vane with fan-shaped holes. The new console film-cooling hole geometry offers advantages to the engine designer due to a superior aerodynamic efficiency over the fan-shaped hole geometry. These efficiency measurements are demonstrated by results from midspan traverses of a four-hole pyramid probe downstream of the nozzle guide vane.

Film Cooling Research on the Endwall of a Turbine Nozzle Guide Vane in a Short Duration Annular Cascade: Part 2—Analysis and Correlation of Results

1992 ◽  
Vol 114 (4) ◽  
pp. 741-746 ◽  
Author(s):  
S. P. Harasgama ◽  
C. D. Burton
Keyword(s):  
Heat Transfer ◽  
Pressure Gradient ◽  
Film Cooling ◽  
Guide Vane ◽  
Three Dimensional ◽  
Companion Paper ◽  
Hole Injection ◽  
Nozzle Guide Vane ◽  
Nozzle Guide ◽  
Annular Cascade

Results have been presented on the heat transfer characteristics of the film cooled endwall (platform) of a turbine nozzle guide vane in an annular cascade at engine representative conditions in a companion paper by Harasgama and Burton (1992). The present paper reports on the analysis of these measurements. The experimental results are well represented by the superposition theory of film cooling. It is shown that high cooling effectiveness can be achieved when the data are corrected for axial pressure gradients. The data are correlated against both the slot-wall jet parameter and the discrete hole injection function for flat-plate, zero pressure gradient cases. The pressure gradient correction brings the present data to within ± 11 percent of the discrete hole correlation. Preliminary predictions of heat transfer reduction have been carried out using the STANCOOL program. These indicate that the code can predict the magnitude of heat transfer reduction correctly, although the absolute values are not in good agreement. This is attributed to the three-dimensional nature of the flow at the endwall.

The Effect of Film Cooling on Nozzle Guide Vane Deposition

2013 ◽  
Author(s):  
C. Bonilla ◽  
C. Clum ◽  
M. Lawrence ◽  
B. Casaday ◽  
J. P. Bons
Keyword(s):  
Surface Temperature ◽  
Film Cooling ◽  
Guide Vane ◽  
Particle Temperature ◽  
Test Facility ◽  
Minor Effect ◽  
Engine Operation ◽  
Infrared Measurements ◽  
Nozzle Guide Vane ◽  
Nozzle Guide

An accelerated deposition test facility was used to study the relationship between film cooling, surface temperature, and particle temperature on deposit formation. Tests were run at gas turbine representative inlet Mach numbers (0.1) and temperatures (1090°C). Deposits were created from lignite coal fly ash with mass median diameters of 1.3 and 8.8μm. Two CFM56-5B nozzle guide vane doublets, comprising three full passages and two half passages of flow, were utilized as the test articles. Tests were run with different levels of film cooling back flow margin and coolant temperature. Particle temperature upon impact with the vane surface was shown to be the leading factor in deposition. Since the particle must traverse the boundary layer of the cooled vane before impact, deposition is directly affected by the film and metal surface temperature as well. Film coolant jet strength showed only minor effect on deposit patterns on the leading edge. However, larger Stokes number (resulting in higher particle impact temperature) corresponded with increased deposit coverage area on the showerhead region. Additionally, infrared measurements showed a strong correlation between regions of greater deposits and elevated surface temperature on the pressure surface. Thickness distribution measurements also highlighted the effect of film cooling by showing reduced deposition immediately downstream of cooling holes. Implications for engine operation in particulate-laden environments are discussed.

Sign in / Sign up

Export Citation Format

Share Document