Specification for High-Carbon Steel Joint Bars; Replaced by A 3

10.1520/a0005 ◽  
1978 ◽  
Author(s):  
Keyword(s):  
Carbon Steel ◽  
High Carbon Steel ◽  
High Carbon ◽  
Steel Joint

Friction Hydro-Pillar Processing of a High Carbon Steel: Joint Structure and Properties

2018 ◽  
Vol 49 (2) ◽  
pp. 699-708 ◽  
Author(s):  
Luis Fernando Kanan ◽  
Buchibabu Vicharapu ◽  
Antonio Fernando Burkert Bueno ◽  
Thomas Clarke ◽  
Amitava De
Keyword(s):  
Carbon Steel ◽  
High Carbon Steel ◽  
Structure And Properties ◽  
High Carbon ◽  
Steel Joint ◽  
Joint Structure

Bonding and Separation Behaviors between Ti-Sn Alloys and High Carbon Steel

2010 ◽  
Vol 638-642 ◽  
pp. 3787-3792 ◽  
Author(s):  
Yasuhiro Morizono ◽  
Seiichiro Nakatsukasa ◽  
Minoru Nishida
Keyword(s):  
Shear Strength ◽  
Carbon Steel ◽  
Elevated Temperatures ◽  
Alloy Composition ◽  
Bonding Temperature ◽  
High Carbon Steel ◽  
Binary Alloys ◽  
High Carbon ◽  
Steel Joint

Ti-Sn binary alloys (Ti-5 to 20 mol% Sn) were diffusion-bonded to high carbon steel between 1073 and 1273 K for 3.6 ks in a vacuum to investigate the influence of the alloy composition on the interfacial microstructures. Ti-5 and 10 mol% Sn alloys were attached firmly to the steel at a bonding temperature of 1273 K. A continuous TiC layer was formed along the interface, while voids were observed between the TiC layer and the steel. Although the joints with Ti-15 and 20 mol% Sn alloys were also prepared at 1273 K, these joints separated near the interface after the bonding treatment. The TiC layer was formed in the separated surface of Ti-Sn alloy, and Fe in the steel diffused into the Ti-Sn alloy. This indicates that the Ti-15 and 20 mol% Sn alloys established contact with the steel at elevated temperatures until just before the separation. The specimens bonded at 1173 K also denoted the same tendency. However, the Ti-15 mol% Sn/steel joint bonded at 1073 K showed a shear strength of more than 50 MPa. The mechanism and the application of the interface separation are discussed on the basis of the microstructural observations.

Internal friction in a martensitic high-carbon steel

2001 ◽  
Vol 81 (12) ◽  
pp. 2797-2808
Author(s):  
Rustem Bagramov, Daniele Mari, Willy Benoi
Keyword(s):  
Carbon Steel ◽  
Internal Friction ◽  
High Carbon Steel ◽  
High Carbon

Weldability of electroslag remelted high-carbon steel at flash-butt welding

2019 ◽  
Vol 2019 (3) ◽  
pp. 29-37
Author(s):  
A.A. Polishko ◽  
◽  
L.B. Medovar ◽  
A.P. Stovpchenko ◽  
E.V. Antipin ◽  
...  
Keyword(s):  
Carbon Steel ◽  
High Carbon Steel ◽  
High Carbon ◽  
Butt Welding

On the Measurement of Modulus in Torsion of High Carbon Steel Wire by Torsion Tester

1967 ◽  
Vol 53 (11) ◽  
pp. 1342-1344
Author(s):  
Akira NAKAGAWA ◽  
Akihiro SUZUKI ◽  
Tadatsugu KISHIGAMI ◽  
Norio NAGAI
Keyword(s):  
Carbon Steel ◽  
Steel Wire ◽  
High Carbon Steel ◽  
High Carbon

UNS G10600

Alloy Digest ◽  
1991 ◽  
Vol 40 (3) ◽  
Keyword(s):  
Fracture Toughness ◽  
Carbon Steel ◽  
Physical Properties ◽  
Tensile Properties ◽  
High Carbon Steel ◽  
Heat Treating ◽  
High Carbon ◽  
Steel Mills

Abstract UNS No. G 10600 is a high-carbon steel of low hardenability. It may be used in the as-rolled, annealed, normalized or quenched and-tempered condition, depending on the desired properties. This datasheet provides information on composition, physical properties, hardness, elasticity, and tensile properties as well as fracture toughness. It also includes information on forming, heat treating, machining, and joining. Filing Code: CS-129. Producer or source: Carbon steel mills.

Sign in / Sign up

Export Citation Format

Share Document