The Effect of Fiber Dowel Heights in Resin Composite Cores on Restoration Failures of Endodontically Treated Teeth

2009 ◽  
Vol 35 (2) ◽  
pp. 63-69 ◽  
Author(s):  
Trakol Mekayarajjananonth ◽  
Nattinee Chitcharus ◽  
Sheldon Winkler ◽  
Meredith C. Bogert
Keyword(s):  
Fracture Resistance ◽  
Resin Composite ◽  
Endodontically Treated Teeth ◽  
Tooth Structure ◽  
Fiber Posts ◽  
Group 3 ◽  
Group 5 ◽  
Group 2 ◽  
Group 1

Abstract In vitro and in vivo testing suggest that fiber posts may reduce the incidence of root fractures of endodontically treated teeth. The purpose of this in vitro study was to compare the effect of fiber post height in resin composite cores on the fracture resistance of endodontically treated teeth. Forty maxillary central incisors were randomly divided into 2 control groups (Groups 1 and 2) of 5 teeth each, and 3 experimental groups (Groups 3, 4, and 5) of 10 teeth each. The teeth in Group 1 had their opening restored with composite resin, the teeth in Group 2 were restored with quartz fiber posts without resin composite cores, and the teeth in Groups 3, 4, and 5 were restored with quartz fiber posts of 2, 4, and 6 mm high, respectively, in 6-mm resin composite cores. Ceramic crowns were fabricated for the specimens. Specimens were positioned in a mounting device and aligned at a 130-degree angle to the long axis of each tooth. A universal testing machine was used to apply constant load at a crosshead speed of 0.5 mm/min until failure occurred. The highest fracture load and mode of failure of each specimen was recorded. The highest fracture resistance force was observed in Group 2 (290.38 ± 48.45 N) and decreased, respectively, in Group 1 (238.98 ± 26.26 N), Group 5 (228.35 ± 58.79 N), Group 4 (221.43 ± 38.74 N), and Group 3 (199.05 ± 58.00 N). According to one-way analysis of variance (ANOVA) and Duncan's test (P ≤ .05), there was no statistically significant increase in the force from Group 3 to Group 5, and the force in Group 2 was significantly higher than that of the experimental groups. There was no statistical significance difference in force among the experimental groups, and the amount of residual tooth structure was found to be the critical factor in fracture resistance. The results suggest that endodontically treated teeth should be restored with the longest possible post height while preserving maximum tooth structure.

Evaluation of the Effect of Different Ferrule Designs on the Fracture Resistance of Endodontically Treated Maxillary Central Incisors Incorporating Fiber Posts, Composite Cores and Crown Restorations

2007 ◽  
Vol 8 (7) ◽  
pp. 62-69 ◽  
Author(s):  
Emre Ozel ◽  
Idil Dikbas ◽  
Jale Tanalp ◽  
Temel Koksal ◽  
Mustafa Ersoy
Keyword(s):  
Fracture Resistance ◽  
Quartz Fiber ◽  
Group 4 ◽  
Fiber Posts ◽  
Significant Difference ◽  
Group 6 ◽  
Group 3 ◽  
Group 5 ◽  
Group 2 ◽  
Group 1

Abstract Aim The purpose of this study was to evaluate the fracture resistance of endodontically treated maxillary central incisors restored with quartz fiber posts, composite cores, and crowns when different types of ferrule designs were incorporated. Methods and Materials Sixty maxillary incisors were divided into six groups: Group 1 (control): teeth with root canal treatments having a full crown prosthesis; Group 2: teeth with a 2 mm circumferential ferrule; Group 3: teeth with a 2 mm ferrule only in the vestibular region; Group 4: teeth with a 2 mm ferrule only in the palatal region; Group 5: teeth with a 2 mm ferrule in the vestibular and palatal region, having cavities in both proximal areas; and Group 6: teeth with no ferrule. The teeth in the experimental groups were restored with quartz fiber posts-composite cores and full metallic crowns. All experimental teeth were subjected to an increasing compressive force with a crosshead speed of 1 mm/min, until fracture occurred. Results The median fracture values of groups were as follows: Group 1: 574.4 N, Group 2: 472.4 N, Group 3: 474.3 N, Group 4: 480.7 N, Group 5: 463.1 N, and Group 6: 297.9 N. A statistically significant difference was found between Group 1 and Group 6 (p< 0.01). Conclusion It was concluded different ferrule designs did not have any influence on the fracture resistance of teeth with fiber posts. The results of this study indicate fiber posts can safely be used for their reinforcing properties. Furthermore, there is no significant change in the resistance of teeth with fiber posts regardless of which ferrule design is incorporated. The property of these types of posts is an additional advantage in clinical practice. Citation Dikbas I, Tanalp J, Ozel E, Koksal T, Ersoy M. Evaluation of the Effect of Different Ferrule Designs on the Fracture Resistance of Endodontically Treated Maxillary Central Incisors Incorporating Fiber Posts, Composite Cores and Crown Restorations. J Contemp Dent Pract 2007 November; (8)7:062-069.

scholarly journals Effect of the number of thermocycles on microleakage of resin composite restorations

2003 ◽  
Vol 17 (4) ◽  
pp. 337-341 ◽  
Author(s):  
Flávia Bittencourt Pazinatto ◽  
Bruno Barbosa Campos ◽  
Leonardo César Costa ◽  
Maria Teresa Atta
Keyword(s):  
Resin Composite ◽  
Control Group ◽  
Group 4 ◽  
Thermal Changes ◽  
Group 3 ◽  
Group 5 ◽  
Group 2 ◽  
Number Of Cycles ◽  
Group 1

Thermocycling simulates, in vitro, thermal changes that occur in the oral cavity. The aim of this study was to evaluate the influence of the number of cycles on microleakage. Class V cavities (1.5 mm deep, 3 mm in height and 3 mm in width) were prepared in bovine teeth, restored with a Single Bond/Z250 restorative system (3M/ESPE) and then divided into five groups of ten teeth each: group 1 was not thermocycled (control group), and groups 2, 3, 4 and 5 were thermocycled 500, 1,000, 2,500 and 5,000 times, respectively (5º-55º ± 2ºC, 15 s dwell time). The teeth were immersed in 0.5% basic fuchsin aqueous solution for 24 h, sectioned and the sections with the highest degree of microleakage were selected, scanned and the extent of dye penetration was measured by the ImageTool program. The results submitted to one-way ANOVA showed no significant differences between the groups (p > 0.05). The averages of microleakage values in millimeters were: group 1 (3.92); group 2 (3.13); group 3 (4.48); group 4 (4.33) and group 5 (3.42). Thus, it was concluded that there is no relation between the increase of the number of cycles and the increase in microleakage.

scholarly journals Effect of Reinforcement on the Fracture Resistance of Endodontically Treated Molars by Various Bonded Restorations-An In Vitro Study

2015 ◽  
Vol 03 (02) ◽  
pp. 103-111
Author(s):  
Jaidev Dhillon ◽  
Sachin Passi ◽  
Ajay Chhabra ◽  
◽  
Keyword(s):  
Fracture Resistance ◽  
Resin Composite ◽  
Testing Machine ◽  
In Vitro Study ◽  
Group 4 ◽  
Significant Difference ◽  
Group 3 ◽  
Group 2 ◽  
Group 1

Abstract Objective: To compare and evaluate the fracture resistance of endodontically treated molars reinforced with various bonded restorations and to study the type of fractures in various restorations. Methods: Forty extracted mandibular molars were endodontically treated. MOD (Mesio-Occluso-Distal) cavities were prepared and Mesio-Buccal cusp was reduced in all to provide cuspal coverage. All the teeth were then divided into 4 groups. The cavities in group 1(control) were filled with high copper amalgam. Group 2 was restored with direct resin composite. In group 3 after the priming and bonding procedures as in group 2, cavity surfaces were coated with flowable resin composite. Before curing a piece of polyethylene ribbon fiber was cut and coated with adhesive resin and was embedded inside the flowable composite. The resin composite was cured with visible light cure (VLC) gun. For group 4, restorations were done according to the recommendations provided by the manufacturers of SR Adoro (Ivoclar-Vivadent, Schaan, Liechtenstein) composite material. Compressive fracture strength test was performed after at least 24 hours of the fabrication of the specimens, by application of compressive loading in a Universal testing machine, applied on the occlusal aspect of each specimen with a steel bar. The mean loads necessary to fracture were recorded in Newton and the results were statistically analyzed. Results: Group 4 (indirect composite inlay) had the greater fracture resistance and group 1(Amalgam) had the poorest. Difference between group 1 and 3, group 1 and 4, group 2 and 4 were statistically significant. No statistically significant difference was found between group 1 and 2, group 2 and 3, group 3 and 4. Predominant type of fracture in group 1 and 3 was fracture of tooth below cemento enamel junction at tooth restoration interface without mesio buccal cusp involvement. In group 2 and 4, predominant fractures were of tooth below cemento enamel junction through center of restoration without mesio–buccal cusp involvement.

scholarly journals AN INVITRO COMPARATIVE EVALUATION OF FRACTURE RESISTANCE OF ENDODONTICALLY TREATED TEETH OBTURATED WITH RESILON AND GUTTA-PERCHA

2014 ◽  
Vol 04 (03) ◽  
pp. 075-079
Author(s):  
Kiran Halkai ◽  
Rahul Halkai ◽  
Mithra N. Hegde ◽  
Vijay Kumar ◽  
Keyword(s):  
Fracture Resistance ◽  
Testing Machine ◽  
Control Group ◽  
Endodontically Treated Teeth ◽  
Group 4 ◽  
Anterior Teeth ◽  
Ah Plus ◽  
Group 3 ◽  
Group 2

Abstract Aim: To compare and evaluate in-vitro the fracture resistance of endodontically treated teeth obturated with resilon & epiphany sealer and guttapercha using different sealers. Epoxy resin based sealer AH-plus and zinc oxide eugenol based sealer-TubliSeal (EWT). Methodology: sixty four human single rooted maxillary anterior teeth, cleaned stored in 0.9% saline. All the teeth were decoronated to root length 14mm and bucco-lingual diameter of 5-7mm, After access openings teeth were instrumented using K3.06 up to final apical size 30/.06 and randomly allocated into 4 experimental groups (n=16 per group). Group 1(Control group): teeth were instrumented but not obturated, Group 2: Resilon cones and epiphany SE-sealer. Group 3: guttapercha cones and epoxy based sealer AH plus. Group 4: guttapercha and Tubli seal EWT. Coronal seal was done using IRM cement. Each of the specimens were tested for fracture resistance by instron universal testing machine. Results: Higher fracture resistance values were observed for group 2 (Resilon & Epiphany SE sealer) followed by group 3(Guttapercha & AH Plus sealer) and group 4(Guttapercha & TubliSeal EWT) when compared to group1 (control-instrumented but not obturated). Conclusion: filling the root canals with contemporary polymer based root canal obturating system- Resilon increased the in vitro fracture resistance of endodontically treated teeth.

scholarly journals Fracture Resistance of Composite Veneers with Different Preparation Designs

2016 ◽  
Vol 20 (2) ◽  
pp. 99-103
Author(s):  
Katerina Zlatanovska ◽  
Ljuben Guguvcevski ◽  
Risto Popovski ◽  
Cena Dimova ◽  
Ana Minovska ◽  
...  
Keyword(s):  
Fracture Resistance ◽  
In Vitro Study ◽  
Fracture Load ◽  
Group 3 ◽  
The Mean ◽  
Group 2 ◽  
Preparation Design ◽  
Frequent Localization ◽  
Group 1

Summary Background: The aim of this in vitro study was to examine the fracture load of composite veneers using three different preparation designs. Material and methods: Fifteen extracted, intact, human maxillary central incisors were selected. Teeth were divided into three groups with different preparation design: 1) feather preparation, 2) bevel preparation, and 3) incisal overlap- palatal chamfer. Teeth were restored with composite veneers, and the specimens were loaded to failure. The localization of the fracture was recorded as incisal, gingival or combined. Results: Composite veneers with incisal overlap - palatal chamfer showed higher fracture resistance compared to feather preparation and bevel preparation. The mean (SD) fracture loads were: Group 1: 100.6±8.0 N, Group 2: 107.4±6.8 N, and Group 3: 122.0±8.8 N. The most common mode of failure was debonding for veneers with feather preparation and fracture when incisal edge is reduced. The most frequent localization of fracture was incisal. Conclusion: The type of preparation has a significant effect on fracture load for composite veneers. This study indicates that using an incisal overlap- palatal chamfer preparation design significantly increases the fracture resistance compared to feather and bevel preparation designs.

Influence of Cavity Preparation, Light-curing Units, and Composite Filling on Intrapulpal Temperature Increase in an In Vitro Tooth Model

2014 ◽  
Vol 39 (5) ◽  
pp. E195-E205 ◽  
Author(s):  
SH Choi ◽  
JF Roulet ◽  
SD Heintze ◽  
SH Park
Keyword(s):  
Resin Composite ◽  
The Other ◽  
Temperature Measurements ◽  
Group 4 ◽  
Light Curing ◽  
Group 3 ◽  
Group 2 ◽  
Power Densities ◽  
Group 1

SUMMARY This study examined the effect of both the tooth substance and restorative filling materials on the increase in pulp chamber temperature when using light-curing units with different power densities. The tip of a temperature sensor was positioned on the pulpal dentinal wall of the buccal side of a maxillary premolar. Metal tubes were inserted in the palatal and buccal root of the tooth, one for water inflow and the other for water outflow. Polyethylene tubes were connected from the metal tubes to a pump to control the flow rate. For the unprepared tooth group (group 1), the tooth was light-cured from the buccal side using two light-curing units (three curing modes): the VIP Junior (QTH, BISCO, Schaumburg, IL, USA) and the Bluephase LED light-curing units (two modes: LEDlow and LEDhigh; Ivoclar Vivadent, Schaan, Liechtenstein). The power densities of each light-curing unit for the LEDlow, QTH, and LEDhigh modes were 785 mW/cm2, 891 mW/cm2, and 1447 mW/cm2, respectively. All light-curing units were activated for 60 seconds. For the prepared tooth group (group 2), a Class V cavity, 4.0 mm in width by 4.0 mm in height by 1.8 mm in depth in size, was prepared on the buccal surface of the same tooth for the temperature measurement. The light-curing and temperature measurements were performed using the same methods used in group 1. The cavity prepared in group 2 was filled with a resin composite (Tetric N Ceram A3 shade, Ivoclar Vivadent) (group 3) or a flowable composite (Tetric N Flow with A3 shade, Ivoclar Vivadent) (group 4). The light-curing and temperature measurements were performed for these groups using the same methods used for the other groups. The highest intrapulpal temperature (TMAX) was measured, and a comparison was conducted between the groups using two-way analysis of variance with a post hoc Tukey test at the 95% confidence level. The TMAX values were as follows: 38.4°C (group 1), 39.0°C (group 2), 39.8°C (group 3), and 40.3°C (group 4) for the LEDlow mode. For the QTH mode, the TMAX values were 40.1°C (group 1), 40.4°C (group 2), 40.9°C (group 3), and 41.4°C (group 4). For the LEDhigh mode, the TMAX values were 43.3°C (group 1), 44.5°C (group 2), 44.7°C (group 3), and 45.3°C (group 4). The statistical analysis revealed the following: the TMAX values were arranged by mode in the following manner: LEDlow &lt; QTH &lt; LEDhigh (p&lt;0.05) and group 1 &lt; group 2 ≤ group 3 ≤ group 4 (p&lt;0.05).

scholarly journals Overlays or Ceramic Fragments for Tooth Restoration: An Analysis of Fracture Resistance

2014 ◽  
Vol 15 (1) ◽  
pp. 56-60
Author(s):  
Matheus Coelho Bandéca ◽  
Adriana Santos Malheiros ◽  
Rudys Rodolfo de Jesus Tavarez ◽  
Leily Macedo Firoozmand ◽  
Mônica Barros Silva
Keyword(s):  
Fracture Resistance ◽  
Testing Machine ◽  
Resin Cement ◽  
Posterior Teeth ◽  
Tooth Structure ◽  
Significant Difference ◽  
Group 3 ◽  
Group 2 ◽  
Ceramic Restorations ◽  
Group 1

ABSTRACT Purpose The aim of this study was to evaluate the mode of fracture and resistance of partial ceramic restorations of posterior teeth. Materials and methods Thirty healthy upper premolars were selected and divided into three groups (n = 10): Group 1— control, healthy unrestored teeth, group 2—teeth restored with ceramic fragments; and group 3—teeth restored with ceramic overlays. The restorations were manufactured with feldspathic ceramic and cemented with RelyX ARC resin cement. After being stored in distilled water for 7 days, the teeth were subjected to axial compression mechanical testing with a universal testing machine. Force was applied to the long axis of the tooth at a speed of 0.5 mm/min until fracture. The data were analyzed with one-way ANOVA and Tukey's test (5%). The mode of fracture was scored according to the degree of involvement of the tooth structure and the type of restoration. Results A significant difference (p < 0.05) was showed between groups 2 (1155 N) and 3 (846.6 N), but there was no significant difference between group 1 and the other groups (1046 N), More extensive fractures were prevalent in the healthy teeth group (Group 1), which had no occlusal coverage; less severe fractures were found in groups 2 and 3. Conclusion We conclude that teeth restored with ceramic fragments may offer greater resistance to fractures compared to teeth that have overlay restorations. How to cite this article de Jesus Tavarez RR, Firoozmand LM, Silva MB, Malheiros AS, Bandéca MC. Overlays or Ceramic Fragments for Tooth Restoration: An Analysis of Fracture Resistance. J Contemp Dent Pract 2014;15(1):56-60.

scholarly journals Effect of cyclic loading on fracture strength of endodontically treated teeth restored with conventional and esthetic posts

2006 ◽  
Vol 14 (4) ◽  
pp. 297-303 ◽  
Author(s):  
Anuar Antônio Xible ◽  
Rudys Rodolfo de Jesus Tavarez ◽  
Carlos dos Reis Pereira de Araujo ◽  
Paulo César Rodrigues Conti ◽  
Wellington Cardoso Bonachella
Keyword(s):  
Survival Rate ◽  
Cyclic Loading ◽  
Fracture Strength ◽  
Resin Composite ◽  
Endodontically Treated Teeth ◽  
Core System ◽  
Group 3 ◽  
Post And Core ◽  
Group 2 ◽  
Group 1

INTRODUCTION: Esthetic post and core systems were recently introduced. There are few reports regarding their behavior under cyclic loading. OBJECTIVES: This study compared the effect of cyclic loading on survival rate, residual strength and mode of fracture of endodontically treated teeth restored with esthetic and direct metallic post systems subjected to mechanical cyclic loading. MATERIALS AND METHODS: Thirty canines were endodontically treated, decoronated and prepared for metal free ceramic crowns, leaving 1.5 mm of dentin for ferrule effect. They were distributed in 3 groups and restored as follows: group 1 with zirconia posts (Cosmopost) and glass-ceramic cores (IPS Empress Cosmopost); group 2 with fiber reinforced composite posts (FibreKor) and group 3 with titanium posts (AZthec Anchor). Direct resin composite (Build It FR Resin Composite) was used as core in groups 2 and 3. All specimens were restored with all ceramic crowns (IPS Empress 2). A resin cement/adhesive system (Cement It/Bond It Primer A+B) was used to lute the posts to root canals and metal free porcelain crowns to the teeth preparation. Specimens were subjected to mechanical load of 250 N for 500,000x at a frequency of 1.7 Hz and then to static load until failure in a universal testing machine. Data were analyzed using One-way ANOVA and Fischer Exact tests alpha=0.05. RESULTS: All groups had 100% survival rate after cyclic loading; fracture strength values (SD) in N were: group 1 = 886.5(170.6), group 2 = 762.2(113.6) and group 3 = 768.9(72.9); there was no difference among groups (p=0.08); the percentage of mode of favorable fracture found was: group 1 = 60%, group 2 = 90% and group 3 = 50%; there was no correlation between the mode of failure and post and core system used (P=0.142). CONCLUSIONS: Esthetic post and core systems showed statistically equivalent fracture strength values, mode of failure and survival rate compared to conventional direct metallic post and resin composite core system after cyclic loading.

Does Perioperative Hemoglobin A1c Level Affect the Incidence, Pattern and Mortality of Lower Extremity Amputation?

2019 ◽  
Vol 17 (4) ◽  
pp. 354-364
Author(s):  
Hassan Al-Thani ◽  
Moamena El-Matbouly ◽  
Maryam Al-Sulaiti ◽  
Noora Al-Thani ◽  
Mohammad Asim ◽  
...  
Keyword(s):  
Glycemic Control ◽  
Lower Extremity ◽  
Hazard Ratio ◽  
Lower Extremity Amputation ◽  
Group 4 ◽  
Group 3 ◽  
Group 5 ◽  
Group 2 ◽  
Extremity Amputation ◽  
Group 1

Background: We hypothesized that perioperative HbA1c influenced the pattern and outcomes of Lower Extremity Amputation (LEA). Methods: A retrospective analysis was conducted for all patients who underwent LEA between 2000 and 2013. Patients were categorized into 5 groups according to their perioperative HbA1c values [Group 1 (<6.5%), Group 2 (6.5-7.4%), Group 3 (7.5-8.4%), Group 4 (8.5-9.4%) and Group 5 (≥9.5%)]. We identified 848 patients with LEA; perioperative HbA1c levels were available in 547 cases (Group 1: 18.8%, Group 2: 17.7%, Group 3: 15.0%, Group 4: 13.5% and Group 5: 34.9%). Major amputation was performed in 35%, 32%, 22%, 10.8% and 13.6%, respectively. Results: The overall mortality was 36.5%; of that one quarter occurred during the index hospitalization. Mortality was higher in Group 1 (57.4%) compared with Groups 2-5 (46.9%, 38.3%, 36.1% and 31.2%, respectively, p=0.001). Cox regression analysis showed that poor glycemic control (Group 4 and 5) had lower risk of mortality post-LEA [hazard ratio 0.57 (95% CI 0.35-0.93) and hazard ratio 0.46 (95% CI 0.31-0.69)]; this mortality risk persisted even after adjustment for age and sex but was statistically insignificant. The rate of LEA was greater among poor glycemic control patients; however, the mortality was higher among patients with tight control. Conclusion: The effects of HbA1c on the immediate and long-term LEA outcomes and its therapeutic implications need further investigation.

scholarly journals Association between serum oestradiol level on the hCG administration day and neonatal birthweight after IVF-ET among 3659 singleton live births

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Yu Liu ◽  
Jing Li ◽  
Wanyu Zhang ◽  
Yihong Guo
Keyword(s):  
Birth Weight ◽  
Ovarian Stimulation ◽  
Group 4 ◽  
Group 6 ◽  
Group 3 ◽  
Group 5 ◽  
Group 2 ◽  
The Impact ◽  
Ivf Et ◽  
Group 1

AbstractOestradiol, an important hormone in follicular development and endometrial receptivity, is closely related to clinical outcomes of fresh in vitro fertilization-embryo transfer (IVF-ET) cycles. A supraphysiologic E2 level is inevitable during controlled ovarian hyper-stimulation (COH), and its effect on the outcome of IVF-ET is controversial. The aim of this retrospective study is to evaluate the association between elevated serum oestradiol (E2) levels on the day of human chorionic gonadotrophin (hCG) administration and neonatal birthweight after IVF-ET cycles. The data of 3659 infertile patients with fresh IVF-ET cycles were analysed retrospectively between August 2009 and February 2017 in First Hospital of Zhengzhou University. Patients were categorized by serum E2 levels on the day of hCG administration into six groups: group 1 (serum E2 levels ≤ 1000 pg/mL, n = 230), group 2 (serum E2 levels between 1001 and 2000 pg/mL, n = 524), group 3 (serum E2 levels between 2001 and 3000 pg/mL, n = 783), group 4 (serum E2 levels between 3001 and 4000 pg/mL, n = 721), group 5 (serum E2 levels between 4001 and 5000 pg/mL, n = 548 ), and group 6 (serum E2 levels > 5000 pg/mL, n = 852). Univariate linear regression was used to evaluate the independent correlation between each factor and outcome index. Multiple logistic regression was used to adjust for confounding factors. The LBW rates were as follows: 3.0% (group 1), 2.9% (group 2), 1.9% (group 3), 2.9% (group 4), 2.9% (group 5), and 2.0% (group 6) (P = 0.629), respectively. There were no statistically significant differences in the incidences of neonatal LBW among the six groups. We did not detect an association between peak serum E2 level during ovarian stimulation and neonatal birthweight after IVF-ET. The results of this retrospective cohort study showed that serum E2 peak levels during ovarian stimulation were not associated with birth weight during IVF cycles. In addition, no association was found between higher E2 levels and increased LBW risk. Our observations suggest that the hyper-oestrogenic milieu during COS does not seem to have adverse effects on the birthweight of offspring after IVF. Although this study provides some reference, the obstetric-related factors were not included due to historical reasons. The impact of the high estrogen environment during COS on the birth weight of IVF offspring still needs future research.

Sign in / Sign up

Export Citation Format

Share Document