MIXING LAYER STRUCTURE OF A JET IN A WIND TUNNEL WITH AN OPEN TEST SECTION

2017 ◽  
Vol 48 (8) ◽  
pp. 711-722
Author(s):  
N. I. Batura ◽  
Valery Viktorovich Vozhdaev ◽  
Gadzhi Gadzhimagomaevich Gadzhimagomedov ◽  
Igor Ivanovich Lipatov
2018 ◽  
Author(s):  
S. A. Baranov ◽  
N. I. Batura ◽  
G. G. Gadzhimagomedov ◽  
D. S. Sboev

2018 ◽  
Vol 145 ◽  
pp. 03015
Author(s):  
Hardy Weisweiler ◽  
Jasmina Kojouharova ◽  
Roland Dückershoff

The paper is focused on design simulations by the means of commercial software for a low speed circuit wind tunnel with an open test section, recently built at the Department of Mechanical Engineering, Mechatronics and Materials Technology at THM University of Applied Sciences in Friedberg. The proposed wind tunnel has a test section with cross sectional area of 1 X 1 m2 and a length of 1.6 m. The maximum achievable speed is about 50 m/s with empty test section. The simulation had the target to propose and to verify various geometries - test chamber, tunnel contraction, diffuser etc. as well the tunnel corner including the vanes. In addition, the influence of the vanes number and their shape on the ventilator power needed and the flow velocity uniformity as well, have been subjects of the investigation. Also the ventilator type (rotational segment) impact on the flow pattern within the operational area has been scrutinized.


2013 ◽  
Vol 5 (3) ◽  
pp. 305-314 ◽  
Author(s):  
Luciana Bassi Marinho Pires ◽  
Igor Braga De Paula ◽  
Gilberto Fisch ◽  
Ralf Gielow ◽  
Roberto Da Mota Girardi

1997 ◽  
Vol 200 (10) ◽  
pp. 1441-1449 ◽  
Author(s):  
C J Pennycuick ◽  
T Alerstam ◽  
A Hedenström

A new wind tunnel for experiments on bird flight was completed at Lund University, Sweden, in September 1994. It is a closed-circuit design, with a settling section containing five screens and a contraction ratio of 12.25. The test section is octagonal, 1.20 m wide by 1.08 m high. The first 1.2 m of its length is enclosed by acrylic walls, and the last 0.5 m is open, giving unrestricted access. Experiments can be carried out in both the open and closed parts, and comparison between them can potentially be used to measure the lift effect correction. The fan is driven by an a.c. motor with a variable-frequency power supply, allowing the wind speed to be varied continuously from 0 to 38 m s-1. The whole machine can be tilted to give up to 8 ° descent and 6 ° climb. A pitot-static survey in the test section showed that the air speed was within ±1.3 % of the mean at 116 out of 119 sample points, exceeding this deviation at only three points at the edges. A hot-wire anemometer survey showed that the turbulence level in the closed part of the test section was below 0.04 % of the wind speed throughout most of the closed part of the test section, rising to approximately 0.06 % in the middle of the open part. No residual rotation from the fan could be detected in the test section. No decrease in wind speed was detectable beyond 3 cm from the side walls of the closed part, and turbulence was minimal beyond 10 cm from the walls. The installation of a safety net at the entrance to the test section increased the turbulence level by a factor of at least 30, to 1.2 % longitudinally and 1.0 % transversely.


Sign in / Sign up

Export Citation Format

Share Document