Measuring Coral Skeletal Architecture Using Image Analysis v1

Author(s):  
Rowan Mclachlan ◽  
Ashruti Patel ◽  
Andrea G Grottoli

Coral morphology is influenced by genetics, the environment, or the interaction of both, and thus is highly variable. This protocol outlines a non-destructive and relatively simple method for measuring Scleractinian coral sub-corallite skeletal structures (such as the septa length, theca thickness, and corallite diameter, etc.) using digital images produced as a result of digital microscopy or from scanning electron microscopy. This method uses X and Y coordinates of points placed onto photomicrographs to automatically calculate the length and/or diameter of a variety of sub-corallite skeletal structures in the Scleractinian coral Porites lobata. However, this protocol can be easily adapted for other coral species - the only difference may be the specific skeletal structures that are measured (for example, not all coral species have a pronounced columella or pali, or even circular corallites). This protocol is adapted from the methods described in Forsman et al. (2015) & Tisthammer et al. (2018). There are 4 steps to this protocol: 1) Removal of Organic Tissue from Coral Skeletons 2) Imaging of Coral Skeletons 3) Photomicrograph Image Analysis 4) Calculation of Corallite Microstructure Size This protocol was written by Dr. Rowan McLachlan and was reviewed by Ashruti Patel and Dr. Andréa Grottoli. Acknowledgments Leica DMS 1000 and Scanning Electron Microscopy photomicrographs used in this protocol were acquired at the Subsurface Energy Materials Characterization and Analysis Laboratory (SEMCAL), School of Earth Sciences at The Ohio State University, Ohio, USA. I would like to thank Dr. Julie Sheets, Dr. Sue Welch, and Dr. David Cole for training me on the use of these instruments.

2017 ◽  
Vol 130 (10) ◽  
pp. 1845-1855 ◽  
Author(s):  
Faye M. Nixon ◽  
Thomas R. Honnor ◽  
Nicholas I. Clarke ◽  
Georgina P. Starling ◽  
Alison J. Beckett ◽  
...  

2015 ◽  
Vol 59 (3) ◽  
pp. 87-90 ◽  
Author(s):  
J. Stoulil ◽  
P. Šedá ◽  
M. Anisová ◽  
Z. Fencl ◽  
P. Novák ◽  
...  

Abstract The paper is focused on analyses of dark copper patina defects that were formed on one sheet under the same conditions. Roofs of ten historical buildings were studied by image analysis and samples of two roofs were subjected to more detailed destructive analysis. These samples were studied by means of scanning electron microscopy with energy dispersive X-ray spectroscopy, X-ray diffraction and infrared spectroscopy. Both types of patina are composed of brochantite. Green patinas consisted of a pure brochantite and they had a fl at and compact surface. Conversely, black patina contained a high degree of impurities (ammonia cations, nitrates, silicates) and the surface was rough. The proportion of dark patina was higher in south and east facing surfaces, where washing by rainfall is more difficult.


2010 ◽  
Vol 177 ◽  
pp. 530-532 ◽  
Author(s):  
Xin Gang Yu ◽  
Shi Song Luo ◽  
Yan Na Gao ◽  
Hong Fei Wang ◽  
Yue Xiang Li ◽  
...  

The pore structure and microstructure of the foam concrete was analyzed by scanning electron microscopy and light microscopy combined with digital image analysis. The results show that: (1) even-distributed fine and close pores resulting in high strength and low permeability; (2) uneven-distributed large size pores and open pores lead to low strength and high permeability; (3) light microscopy combined with digital image analysis is a cheap and convenient tool fitting for the pore structure analysis of the foam concrete; (4) scanning electron microscopy is very appropriate for the pore structure and microstructure analysis of the foam concrete.


2012 ◽  
Vol 535-537 ◽  
pp. 280-283 ◽  
Author(s):  
Hao Ran An ◽  
Feng Shi Cai ◽  
Xue Wei Wang ◽  
Zhi Hao Yuan

Different morphology CuO nanostructures, including platelets, flower-like were simply synthesized at 350 °C controlled by droplet on hydrophobic substrate. This is a simple method which does not require any template, catalyst, or surfactant but can control the morphology of CuO from platelets to flowerlike. The morphologies are strongly dependent on the volume of droplet. Scanning electron microscopy (SEM), Optical microscope and X-ray diffraction (XRD) were used to observe the morphology, crystallinity, and chemical composition of the CuO structures. Growth mechanisms for shape selective CuO synthesis were proposed based on these results.


2016 ◽  
Vol 368 ◽  
pp. 146-149
Author(s):  
Eva Macajová

This study is mainly focused on the study of pore size and shape, fibre diameter and also on the optimization of polymer solution composition and electrospinning parameters with respect to the final structure and morphology of PLA nano/microfibrous layers. The nano/microfibres were produced by electrospinning from the needle. Except the spinning process parameters, the morphology of nanofibrous layers can be also affected by the composition of the polymer solution and by the used solvents. Variations in technological process allows us to design the shape and form of nanofibrous structures upon request. The morphology of nano/microfibres was observed by scanning electron microscopy (SEM). Following image analysis and calculation enables the assessment of porosity contribution to the increase in micro/nanofibre surface area.


Sign in / Sign up

Export Citation Format

Share Document