Evidence in Variscan Corsica of a brief and voluminous Late Carboniferous to Early Permian volcanic-plutonic event contemporaneous with a high-temperature/low-pressure metamorphic peak in the lower crust

2015 ◽  
Vol 186 (2-3) ◽  
pp. 171-192 ◽  
Author(s):  
Philippe Rossi ◽  
Alain Cocherie ◽  
C. Mark Fanning

Abstract The U2 group of plutonic rocks constituting the main exposed part of the Corsica-Sardinia batholith (CSB) was emplaced from 308 to 275 Ma (the early Visean U1 group of Mg-K intrusions is not considered here). Field evidence earlier established volcanic-plutonic relationships in the U2 group of calc-alkaline intrusions of the CSB, though detailed chronological data were still lacking. Large outcrops of U2 volcanic formations are restricted to the less eroded zone north-west of the Porto-Ponte Leccia line in Corsica, but volcanic and volcano-sedimentary formations were widely eroded elsewhere since Permian times. They probably covered most of the batholith before the Miocene, as testified by the volcanic nature of the pebbles that form much of the Early Miocene conglomerates of eastern Corsica. U-Pb zircon dating (SHRIMP) was used for deciphering the chronology and duration of different volcanic pulses and for better estimating the time overlap between plutonic and volcanic rock emplacement in the CSB. The obtained ages fit well with field data, showing that most of the U2 and U3 volcanic formations were emplaced within a brief time span of roughly 15 m.y., from 293 to 278 Ma, coeval with most U2 monzogranodiorites and leucomonzogranites (295–280 Ma), alkaline U3 complexes (about 288 Ma), and mafic-ultramafic tholeiitic complexes (295–275 Ma). The same chronological link between deep-seated magma chambers and eruptions was identified in the Pyrenees. These results correlate with U-Pb zircon dating of HT-LP granulites from the Variscan deep crust exhumed along the “European” margin of the thinned Tethys margin in Corsica and Calabria. Here, the peak of the low-pressure/high-temperature metamorphism was dated at about 285–280 Ma. Our results throw light on the condition of magma production during the orogenic collapse in the southern Variscan realm. While juvenile tholeiitic basaltic magma was produced by the melting of spinel mantle lithosphere, all fertile protoliths melted in a brief period during the HT-LP peak in lower continental crust, leading to massive emplacement of large felsic U2 calc-alkaline and minor U3 A-type volcano-plutonic formations over about 15 Ma.

2002 ◽  
Vol 43 (4) ◽  
pp. 663-703 ◽  
Author(s):  
T. C. FEELEY ◽  
M. A. COSCA ◽  
C. R. LINDSAY

Abstract The petrogenesis of calc-alkaline magmatism in the Eocene Absaroka Volcanic Province (AVP) is investigated at Washburn volcano, a major eruptive center in the low-K western belt of the AVP. New 40Ar/39Ar age determinations indicate that magmatism at the volcano commenced as early as 55 Ma and continued until at least 52 Ma. Although mineral and whole-rock compositional data reflect near equilibrium crystallization of modal phenocrysts, petrogenetic modeling demonstrates that intermediate composition magmas are hybrids formed by mixing variably fractionated and contaminated mantle-derived melts and heterogeneous silicic crustal melts. Nd and Sr isotopic compositions along with trace element data indicate that silicic melts in the Washburn system are derived from deep-crustal rocks broadly similar in composition to granulite-facies xenoliths in the Wyoming Province. Our preferred explanation for these features is that mantle-derived basaltic magma intruded repeatedly in the deep continental crust leading to fractional crystallization, silicic melt production, and homogenization of magmas, followed by ascent to shallow reservoirs and crystallization of new plagioclase-rich mineral assemblages in equilibrium with the intermediate hybrid liquids. The implications of this process are that (1) some calc-alkaline magmas may only be recognized as hybrids on purely chemical grounds, particularly in systems where mixing precedes and is widely separated from crystallization in space and time, and (2) given the role ascribed to crustal processes at Washburn volcano, the variation between rocks that follow calc-alkaline trends in the western AVP and those that follow shoshonitic trends in the east cannot simply reflect higher pressures of fractionation to the east in Moho-level magma chambers in the absence of crustal interaction.


JOM ◽  
1961 ◽  
Vol 13 (7) ◽  
pp. 490-493 ◽  
Author(s):  
R. A. Perkins ◽  
D. D. Crooks

2021 ◽  
pp. 1-9
Author(s):  
Long Wang ◽  
Dongsheng Yang ◽  
Jiao Chen ◽  
Hui Tan ◽  
Shengyu Zhu ◽  
...  

Author(s):  
O. Namur ◽  
Bénédicte Abily ◽  
Alan E. Boudreau ◽  
Francois Blanchette ◽  
John W. M. Bush ◽  
...  

2019 ◽  
Vol 2019 (1) ◽  
pp. 000387-000392 ◽  
Author(s):  
Sri Krishna Bhogaraju ◽  
Omid Mokhtari ◽  
Jacopo Pascucci ◽  
Fosca Conti ◽  
Hiren R Kotadia ◽  
...  

Abstract High temperature power electronics based on wide-bandgap semiconductors have prominent applications, such as automotive, aircrafts, space exploration, oil/gas extraction, electricity distribution. Die-attach bonding process is an essential process in the realization of high temperature power devices. Here Cu offers to be a promising alternative to Ag, especially because of thermal and mechanical properties on par with Ag and a cost advantage by being a factor 100 cheaper than Ag. With the aim to achieve a low-pressure Cu sintering process, a low cost wet chemical etching process is developed to selectively etch Zn from brass to create nano-porous surface modifications to enhance sinterability, enabling sintering with low bonding pressure of 1MPa and at temperatures below 300°C. However, high tendency of Cu to oxidize poses a major challenge in realizing stable interconnects. For this purpose, in this contribution, we present the use of polyethylene-glycol 600 as reducing binder in the formulation of the Cu sintering paste. Finally, we propose a multi-pronged approach based on three crucial factors: surface-modified substrates, nanostructured surface modifications on micro-scale Cu-alloy particles and use of a reducing binder in the Cu particle paste.


Sign in / Sign up

Export Citation Format

Share Document