Proppant Transport in Complex Fracture Networks

Author(s):  
Kaustubh Shrivastava ◽  
Mukul M. Sharma
Author(s):  
Hannes Hofmann ◽  
Tayfun Babadagli ◽  
Günter Zimmermann

The creation of large complex fracture networks by hydraulic fracturing is imperative for enhanced oil recovery from tight sand or shale reservoirs, tight gas extraction, and Hot-Dry-Rock (HDR) geothermal systems to improve the contact area to the rock matrix. Although conventional fracturing treatments may result in bi-wing fractures, there is evidence by microseismic mapping that fracture networks can develop in many unconventional reservoirs, especially when natural fracture systems are present and the differences between the principle stresses are low. However, not much insight is gained about fracture development as well as fluid and proppant transport in naturally fractured tight formations. In order to clarify the relationship between rock and treatment parameters, and resulting fracture properties, numerical simulations were performed using a commercial Discrete Fracture Network (DFN) simulator. A comprehensive sensitivity analysis is presented to identify typical fracture network patterns resulting from massive water fracturing treatments in different geological conditions. It is shown how the treatment parameters influence the fracture development and what type of fracture patterns may result from different treatment designs. The focus of this study is on complex fracture network development in different natural fracture systems. Additionally, the applicability of the DFN simulator for modeling shale gas stimulation and HDR stimulation is critically discussed. The approach stated above gives an insight into the relationships between rock properties (specifically matrix properties and characteristics of natural fracture systems) and the properties of developed fracture networks. Various simulated scenarios show typical conditions under which different complex fracture patterns can develop and prescribe efficient treatment designs to generate these fracture systems. Hydraulic stimulation is essential for the production of oil, gas, or heat from ultratight formations like shales and basement rocks (mainly granite). If natural fracture systems are present, the fracturing process becomes more complex to simulate. Our simulation results reveal valuable information about main parameters influencing fracture network properties, major factors leading to complex fracture network development, and differences between HDR and shale gas/oil shale stimulations.


2016 ◽  
Author(s):  
Yanmin Xu ◽  
Obinna Daniel Ezulike ◽  
Ashkan Zolfaghari ◽  
Hassan Dehghanpour ◽  
Claudio Virues

Geofluids ◽  
2019 ◽  
Vol 2019 ◽  
pp. 1-19
Author(s):  
Jianwei Feng ◽  
Xu Zhang ◽  
Peng Luo ◽  
Xizhe Li ◽  
He Du

Much research has been conducted on physical and numerical modeling that focus on stress state and structural controls on subsurface geofluid flow, yet very few attempts have been made to discover and quantify the mineral precipitation/dissolution kinetics in complex fracture system such as Tarim Basin of China. We conducted a geochemical simulation study using the outcrop fracture networks in Ordovician carbonate rocks in Tabei Outcrop Area of Tarim Basin. Structural analysis, filling analysis within the fracture networks and surrounding rocks were used to constrain the generation and geochemical evolution of the geofluids. Using an advanced reactive transport simulation platform TOUGHREACT, a pertinent thermodynamic system was applied to establish the geological model of the fracture-surrounding rock, where the corresponding calcium carbonate (CaCO3) solution was configured to replace the deep saturated hydrothermal fluids. Different types of mineral parameters were considered with material balance and phase equilibrium calculation to perform numerical simulation of multi-field, e.g., pressure field, temperature field, seepage field and chemical field under formation conditions. The simulation results were consistent with field observations. The major findings of this simulation study include: (1) Along with fluid injection, local dissolution occurred within the fractures and matrix, but with the gradual saturation of calcium ions and the increasing pH value, considerable calcite precipitation occurred. (2) The dissolution/precipitation in different fractures was mainly affected by their structure and physical properties, resulting in changes in fluid flow rate, temperature, pressure and ion concentration over time. (3) In the same group, the degree of mineral filling of small-aperture fractures, low-angle fractures and shallow fractures was significantly higher than other types of fractures. (4) The better the connectivity between reticular fractures and the higher the linear density of fractures, the lower the mineral filling degree. (5) Dissolution phenomenon strengthened within large-aperture conjugated fractures gradually along the flow direction. The proposed methodologies in this study can be applied to model effective fracture filling of other deep reservoirs.


Sign in / Sign up

Export Citation Format

Share Document