Development Features of Cold Production with Horizontal Wells in a Foamy Extra-Heavy Oil Reservoir

2021 ◽  
Author(s):  
Zhaopeng Yang ◽  
Xingmin Li ◽  
Xinxia Xu ◽  
Yang Shen ◽  
Xiaoxing Shi
Keyword(s):  
Heavy Oil ◽  
Horizontal Wells ◽  
Oil Field ◽  
Production Performance ◽  
Oil Reservoirs ◽  
Bubble Point ◽  
Foamy Oil ◽  
Bubble Point Pressure ◽  
Heavy Oil Reservoirs ◽  
Point Pressure

Abstract The block M as a foamy extra-heavy oil field in the Carabobo Area, the eastern Orinoco Belt, has been exploited by foamy oil cold production utilizing horizontal wells. The early producing area of block M has been put into production more than 10 years. And the development features of cold production in foamy extra-heavy oil reservoirs are different from the conventional oil field. It is necessary to investigate the development features of this kind reservoir and analyze its influence factors. Combining the production data with the reservoir geological characteristics of the research area, the cold production features of foamy extra-heavy oil using horizontal wells are analyzed. Then numerical simulations were adopted to study the influence factors of cold production performance. In the early stage of cold production, the oil production rate is high and the producing GOR is low. With the process of cold production, the reservoir pressure decreases gradually, the producing GOR increases gradually, and the oil production rate decreases gradually. When the bottom hole flowing pressure drops to below the bubble point pressure, the flow of extra-heavy oil in the reservoir can be divided into two zones: far well zone and near well area. In the far well zone, the pressure is higher than the bubble point pressure. The flow of oil is a single-phase flow, and the displacement mode is elastic driving. In the near well area, the pressure is lower than the bubble point pressure, and the oil flow is foamy oil flow, and the displacement mode is the dissolving gas drive driven by foamy oil. There exists many factors that influence the cold production performance of foamy extra-heavy oil, including reservoir depth, reservoir thickness, reservoir physical property and heterogeneity. The oil recovery factor per unit pressure drop can evaluate the cold production performance of foamy extra-heavy oil reservoirs. The effectiveness of cold production is closely related to reservoir parameters. Larger reservoir thickness, deeper reservoir depth and greater reservoir permeability will enhance the performance of cold production. Closer, larger and more interlayers above the horizontal well will hinder the performance of cold production. This research provides certain guidance and reference for further development adjustment and new project evaluation for foamy extra-heavy oil reservoirs in the Eastern Orinoco Belt.

scholarly journals Comparison of Foamy Oil Behaviour between Shallow and Middepth Heavy Oil Reservoirs in the Orinoco Belt

Geofluids ◽  
2021 ◽  
Vol 2021 ◽  
pp. 1-8
Author(s):  
Xingmin Li ◽  
Changchun Chen ◽  
Zhangcong Liu ◽  
Yongbin Wu ◽  
Xiaoxing Shi
Keyword(s):  
Heavy Oil ◽  
Oil And Gas ◽  
Production Performance ◽  
Oil Reservoirs ◽  
Recovery Factor ◽  
Oil Reservoir ◽  
Foamy Oil ◽  
Heavy Oil Reservoirs ◽  
Heavy Oil Reservoir ◽  
The Difference

Nowadays, extra heavy oil reservoirs in the Orinoco Heavy-Oil-Belt in Venezuela are exploited via cold production process, which present different production performance in well productivity and primary recovery factor. The purpose of this study is to investigate the causes for such differences with the aspect of foamy oil mechanism. Two typical oil samples were adopted from a shallow reservoir in western Junìn region and a middepth reservoir in eastern Carabobo region in the Belt, respectively. A depletion test was conducted using 1D sand-pack with a visualized microscopic flow observation installation for each of the oil samples under simulated reservoir conditions. The production performance, the foamy oil behaviour, and the oil and gas morphology were recorded in real time during the tests. The results indicated that the shallow heavy oil reservoir in the Belt presents a weaker foamy oil phenomenon when compared with the middepth one; its foamy oil behaviour lasts a shorter duration with a smaller scope, with bigger bubble size and less bubble density. The difference in foamy oil behaviour for those two types of heavy oil reservoir is caused by the difference in reservoir pressure, solution GOR, asphaltene content, etc. Cold production presents obvious features of three stages under the action of strong foamy oil displacement mechanism for the middepth heavy oil reservoir, which could achieve a more favourable production performance. In the contrary, no such obvious production characteristics for the shallow heavy oil reservoir are observed due to weaker foamy oil behaviour, and its primary recovery factor is 9.38 percent point lower than which of the middle heavy oil reservoirs.

Multilateral Wells to Improve Production Performance in Heavy Oil Reservoirs: The Challenges of the ZAM-408ML Well

2008 ◽  
Author(s):  
Loris Tealdi ◽  
Maurizio Rampoldi ◽  
Henri Malonga ◽  
Leone Riccobon ◽  
Fabrice Okassa ◽  
...  
Keyword(s):  
Heavy Oil ◽  
Production Performance ◽  
Oil Reservoirs ◽  
Improve Production ◽  
Heavy Oil Reservoirs

scholarly journals Mechanisms on the Injection Conformance Reversion during Polymer Flooding of Offshore Heterogeneous Heavy-Oil Reservoirs

Geofluids ◽  
2021 ◽  
Vol 2021 ◽  
pp. 1-9
Author(s):  
Zhijie Wei ◽  
Xiaodong Kang ◽  
Yuyang Liu ◽  
Hanxu Yang
Keyword(s):  
Polymer Solution ◽  
Heavy Oil ◽  
Flow Resistance ◽  
Polymer Flooding ◽  
Production Performance ◽  
Oil Reservoirs ◽  
Resistance Force ◽  
Oil Viscosity ◽  
Permeable Layer ◽  
Heavy Oil Reservoirs

Injection conformance reversion commonly observed during polymer flooding in offshore heterogeneous heavy-oil reservoirs weakens the volumetric sweep of polymer solution and compromises its EOR results. To investigate its mechanisms and impact factors, one mathematical model to predicate injection conformance behavior is constructed for heterogeneous reservoirs based on the Buckley-Leverett function. The different suction capability of each layer to polymer solution results in distinct change law of the flow resistance force, which in turn reacts upon the suction capability and creates dynamic redistribution of injection between layers. Conformance reversion takes place when the variation ratio of flow resistance force of different layers tends to be the same. The peak value and scope of conformance reversion decrease and reversion timing is advanced as oil viscosity or permeability contrast increases, or polymer concentration or relative thickness of low permeable layer decreases, which compromises the ability of polymer flooding to improve the volumetric sweep and lower suction of the low permeable layer. The features of offshore polymer flooding tend to make the injection conformance V-type and create low-efficiency circulation of polymer in a high permeable layer more easily. These results can provide guidance to improve the production performance of polymer flooding in offshore heterogeneous heavy-oil reservoirs.

Experimental Analysis of the Effects of Varying Temperature and Viscosities on Foamy Oil Production

2021 ◽  
Author(s):  
Jasmine Shivani Medina ◽  
Iomi Dhanielle Medina ◽  
Gao Zhang
Keyword(s):  
Oil Recovery ◽  
Heavy Oil ◽  
Elevated Temperatures ◽  
Oil Production ◽  
Oil Reservoirs ◽  
Oil Viscosity ◽  
Gas Recovery ◽  
Foamy Oil ◽  
Heavy Oil Reservoirs ◽  
Pressure Depletion

Abstract The phenomenon of higher than expected production rates and recovery factors in heavy oil reservoirs captured the term "foamy oil," by researchers. This is mainly due to the bubble filled chocolate mousse appearance found at wellheads where this phenomenon occurs. Foamy oil flow is barely understood up to this day. Understanding why this unusual occurrence exists can aid in the transfer of principles to low recovery heavy oil reservoirs globally. This study focused mainly on how varying the viscosity and temperature via pressure depletion lab tests affected the performance of foamy oil production. Six different lab-scaled experiments were conducted, four with varying temperatures and two with varying viscosities. All experiments were conducted using lab-scaled sand pack pressure depletion tests with the same initial gas oil ratio (GOR). The first series of experiments with varying temperatures showed that the oil recovery was inversely proportional to elevated temperatures, however there was a directly proportional relationship between gas recovery and elevation in temperature. A unique observation was also made, during late-stage production, foamy oil recovery reappeared with temperatures in the 45-55°C range. With respect to the viscosities, a non-linear relationship existed, however there was an optimal region in which the live-oil viscosity and foamy oil production seem to be harmonious.

Improved production performance of heavy oil reservoirs with compacted and shaled-out interlayers

2021 ◽  
pp. 28-31
Author(s):  
А.Т. Zaripov ◽  
◽  
А.R. Razumov ◽  
Аnt.N. Beregovoy ◽  
N.А. Knyazeva ◽  
...  
Keyword(s):  
Heavy Oil ◽  
Production Performance ◽  
Oil Reservoirs ◽  
Heavy Oil Reservoirs

scholarly journals Experimental Investigation of Oil Recovery from Tight Sandstone Oil Reservoirs by Pressure Depletion

Energies ◽  
2018 ◽  
Vol 11 (10) ◽  
pp. 2667 ◽  
Author(s):  
Wenxiang Chen ◽  
Zubo Zhang ◽  
Qingjie Liu ◽  
Xu Chen ◽  
Prince Opoku Appau ◽  
...  
Keyword(s):  
Oil Recovery ◽  
Oil Reservoirs ◽  
Oil Reservoir ◽  
Reservoir Pressure ◽  
Dissolved Gas ◽  
Tight Sandstone ◽  
Bubble Point ◽  
Bubble Point Pressure ◽  
Pressure Depletion ◽  
Point Pressure

Oil production by natural energy of the reservoir is usually the first choice for oil reservoir development. Conversely, to effectively develop tight oil reservoir is challenging due to its ultra-low formation permeability. A novel platform for experimental investigation of oil recovery from tight sandstone oil reservoirs by pressure depletion has been proposed in this paper. A series of experiments were conducted to evaluate the effects of pressure depletion degree, pressure depletion rate, reservoir temperature, overburden pressure, formation pressure coefficient and crude oil properties on oil recovery by reservoir pressure depletion. In addition, the characteristics of pressure propagation during the reservoir depletion process were monitored and studied. The experimental results showed that oil recovery factor positively correlated with pressure depletion degree when reservoir pressure was above the bubble point pressure. Moreover, equal pressure depletion degree led to the same oil recovery factor regardless of different pressure depletion rate. However, it was noticed that faster pressure drop resulted in a higher oil recovery rate. For oil reservoir without dissolved gas (dead oil), oil recovery was 2–3% due to the limited reservoir natural energy. In contrast, depletion from live oil reservoir resulted in an increased recovery rate ranging from 11% to 18% due to the presence of dissolved gas. This is attributed to the fact that when reservoir pressure drops below the bubble point pressure, the dissolved gas expands and pushes the oil out of the rock pore spaces which significantly improves the oil recovery. From the pressure propagation curve, the reason for improved oil recovery is that when the reservoir pressure is lower than the bubble point pressure, the dissolved gas constantly separates and provides additional pressure gradient to displace oil. The present study will help engineers to have a better understanding of the drive mechanisms and influencing factors that affect development of tight oil reservoirs, especially for predicting oil recovery by reservoir pressure depletion.

Pressure Maintenance and Improving Oil Recovery by Means of Immiscible Water-Alternating-CO2 Processes in Thin Heavy-Oil Reservoirs

2013 ◽  
Vol 16 (01) ◽  
pp. 60-71 ◽  
Author(s):  
Sixu Zheng ◽  
Daoyong Yang
Keyword(s):  
Oil Recovery ◽  
Heavy Oil ◽  
Oil Production ◽  
Horizontal Wells ◽  
Operating Conditions ◽  
Oil Reservoirs ◽  
Oil Saturation ◽  
Water Alternating Gas ◽  
Heavy Oil Reservoirs ◽  
Water Cut

Summary Techniques have been developed to experimentally and numerically evaluate performance of water-alternating-CO2 processes in thin heavy-oil reservoirs for pressure maintenance and improving oil recovery. Experimentally, a 3D physical model consisting of three horizontal wells and five vertical wells is used to evaluate the performance of water-alternating-CO2 processes. Two well configurations have been designed to examine their effects on heavy-oil recovery. The corresponding initial oil saturation, oil-production rate, water cut, oil recovery, and residual-oil-saturation (ROS) distribution are examined under various operating conditions. Subsequently, numerical simulation is performed to match the experimental measurements and optimize the operating parameters (e.g., slug size and water/CO2 ratio). The incremental oil recoveries of 12.4 and 8.9% through three water-alternating-CO2 cycles are experimentally achieved for the aforementioned two well configurations, respectively. The excellent agreement between the measured and simulated cumulative oil production indicates that the displacement mechanisms governing water-alternating-CO2 processes have been numerically simulated and matched. It has been shown that water-alternating-CO2 processes implemented with horizontal wells can be optimized to significantly improve performance of pressure maintenance and oil recovery in thin heavy-oil reservoirs. Although well configuration imposes a dominant impact on oil recovery, the water-alternating-gas (WAG) ratios of 0.75 and 1.00 are found to be the optimum values for Scenarios 1 and 2, respectively.

Sign in / Sign up

Export Citation Format

Share Document