Sensitivity of Piezoresistive Pressure Sensors to Acceleration

The article presents the negative aspects of the influence of static and dynamic acceleration on the accuracy of pressure measurement for a selected type of transmitter. The influence of static accelerations from catalog notes was shown and compared with the tests results for a few selected sensors. The results of research on the influence of dynamic acceleration for various types of its variability for selected converters are presented. Moreover, a method of measurement patented by the authors that uses a complex transducer is shown. The method allows for more accurate measurements on moving objects. The tests were performed based on the proposed method. The obtained results of the influence of acceleration on the classical sensor as well as the construction using the proposed method are shown. The paper presents approximate pressure measurement errors resulting from the influence of acceleration. For example, errors in measuring the speed of an airplane may occur without the proposed method. The last part of the article presents a unique design dedicated to a multi-point pressure measurement system, which uses the presented method of eliminating the influence of accelerations on the pressure measurement.

Review of Animal Models to Study Urinary Bladder Function

The urinary bladder (UB) serves as a storage and elimination organ for urine. UB dysfunction can cause multiple symptoms of failure to store urine or empty the bladder, e.g., incontinence, frequent urination, and urinary retention. Treatment of these symptoms requires knowledge on bladder function, which involves physiology, pathology, and even psychology. There is no ideal animal model for the study of UB function to understand and treat associated disorders, as the complexity in humans differs from that of other species. However, several animal models are available to study a variety of other bladder disorders. Such models include animals from rodents to nonhuman primates, such as mice, rats, rabbits, felines, canines, pigs, and mini pigs. For incontinence, vaginal distention might mimic birth trauma and can be measured based on leak point pressure. Using peripheral and central models, inflammation, bladder outlet obstruction, and genetic models facilitated the study of overactive bladder. However, the larger the animal model, the more difficult the study is, due to the associated animal ethics issues, laboratory facility, and budget. This review aims at facilitating adapted animal models to study bladder function according to facility, priority, and disease.

The Effect of Capillary Condensation on the Geomechanical and Acoustic Properties of Tight Formations: An Experimental Study

Capillary condensation is the condensation of the gas inside nano-pore space at a pressure lower than the bulk dew point pressure as the result of multilayer adsorption due to the high capillary pressure inside the small pore throat of unconventional rocks. The condensation of liquid in nano-pore space of rock changes its mechanical and acoustic properties. Acoustic properties variation due to capillary condensation provides us a tool to monitor phase change in reservoir as a result of nano-confinement as well as mapping the area where phase change occurs as well as characterize pore size distribution. This is particularly important for tight formations where confinement has a strong effect on phase behavior that is challenging to measure experimentally. Theoretical studies have examined the effects of capillary condensation; however, these findings have not been verified experimentally. The main objective of this study is to experimentally investigate the effect of capillary condensation on the mechanical and acoustic properties of shale samples. The mechanical and acoustic characterization of the samples was carried out experimentally using a state-of-the-art tri-axial facility at the Colorado School of Mines. The experimental set-up is capable of the simultaneous acquisition of coupled stress, strain, resistivity, acoustic and flow data. Carbon dioxide was used as the pore pressure fluid in these experiments. After a comprehensive characterization of shale samples, experiments were conducted by increasing the pore pressure until condensation occurs while monitoring the mechanical and acoustic properties of the sample to quantify the effect of capillary condensation on the mechanical and acoustic properties of the sample. Experimental data show a 5% increase in Young's Modulus as condensation occurs. This increase is attributed to the increase in pore stiffness as condensation occurs reinforcing the grain contact. An initial decrease in compressional velocity was observed as pore pressure increases before condensation occurs which is attributed to the expansion of the pore volume when pore pressure increases. After this initial decrease, compressional velocity slightly increases at a pressure around 750 - 800 psi which is close to the condensation pressure. We also observed a noticeable increase in shear velocity when capillary condensation occurs, this could be due to the immobility of the condensed liquid phase at the pore throats. The changes of geomechanical and acoustic signatures were observed at around 750 - 800 psi at 27°C, which is the dew point pressure of the fluid in the nano-pore space of the sample at this temperature. While the unconfined bulk dew point pressure of carbon dioxide at the same temperature is 977 psi. Hence, this study marks the first measurement of the dew point of fluid in nano-pore space and potentially leads to the construction of the phase envelope of fluid under confinement.

Overcoming Downhole Fluid Sampling Challenge Using Dual-Port Straddle Packer in Shallow Viscous Reservoir

Objectives/Scope: Downhole fluid sampling of high quality, low contaminated oil samples with a pumpout wireline formation tester (PWFT) in a shallow unconsolidated reservoir with high H2S, high water salinity and filled with viscous oil is a quite challenging operation. Key properties, related to fluid flow in low pressure reservoirs: formation mechanical weakness, drilling invasion and the high contrast on fluid mobility, have resulted in the failure or impracticality of conventional methods for efficient sampling, resulting in a long sampling time causing high rig cost overhead and often highly contaminated oil samples. Most common problems faced during sampling are: Sand production- causing caving and lost seals and no pressure or samples. Sand plugging of the tool flowline. Operation limitation of pressure drawdown- dictated by extremely low formation pressure and mainly due to having saturated pressure around 20 to 30 psia below formation initial pressure (based on 118 bubble point samples measured in the laboratory). To maintain rock stability and low pressure draw down, fluids were pumped at a low rate, resulting in a long operation time, where a single sample take up to 15 – 20 hours of a pump out. Even with the long pumpout time the collected sample is often highly contaminated based on laboratory PVT analysis report. Methods, Procedures, Process Understanding of the formation properties and its rock mechanics helps to design proper operating techniques to overcome the challenge of viscous oil sampling in unconsolidated sand reservoir. A pre-job geomeechanical study of unconfined sand with very low compressive strength, restricted the flow rate to a maximum drawdown per square inch to maintain rock stability while pumping out. Dual-Port Straddle Packer (figure 1) sampling was introduced to overcome the mentioned challenges. Its large flow area (>1000 in² in 8 ½″ OH section) allowed a high total pumping rate while maintaining very low flow rate per square inch at the sand face, which resulted in an ultra-low draw-down flowing pressure to prevent sand collapse and producing below bubble point pressure that could invalidate further PVT studies. Packer inflation pressure has also been limited to a maximum of 150 to 200 psia above hydrostatic pressure to achieve isolation without overcoming the sand weak compressive strength. During the clean-out operation crude oil tend to separate from water based mud (WBM) filtrate in the packed-off interval due to fluid density difference and immiscibility of the two liquids due to the lower shear rate applied (among others). So a water/oil interface forms within the packed-off interval. As pumping continues, this oil/water fluid contact moves toward the bottom inlet port allowing more clean oil to accumulate at the top. Results, Observations, Conclusions: With the advantage of the dual inlet port straddle packer and the independent opening/closing operating design of each port, a clean segregated oil sample was collected from the top port at an early stage of job operation, saving rig time and cost without compromising collected fluids quality that is valid for PVT studies. Novel/Additive Information: Dual-port Straddle Packer with large flow area (plus filters) with ultra-low drawdown pressure to stay above bubble point pressure in shallow heavy oil reservoirs resulted to be another provided a cost effective technology that can be utilized for collecting downhole samples (DHS) that will undergo PVT studies.

CO2 Liquefaction Close to the Triple Point Pressure

For vessel-based transport of liquid CO2 in carbon capture and storage chains, transport at 8 bar(a) enable significant cost reductions compared to transport at higher pressures for most transport distances and volumes. Transport at even lower pressures could further reduce the costs. There are, however, concerns related to dry ice formation and potential clogging in parts of the chain that could lead to operational issues when operating close to the triple point pressure of CO2. In this paper, results from an experimental campaign to de-risk and gain operational experience from the low-pressure CO2 liquefaction process are described. Six experiments using pure CO2 or CO2/N2 mixtures are presented. In four of the experiments, the liquid product pressure was continuously lowered until dry ice was detected and eventually clogged the system. In the final two experiments, the liquefaction process was run in steady-state at low liquefaction pressures for five hours to ensure that there is no undetected dry ice in the process that could lead to accumulation and operational issues over time. These experiments demonstrate that pure CO2 can be safely liquefied at 5.8 bar(a) and a CO2/N2 mixture can be liquefied at 6.5 bar(a) without issues related to dry ice formation.

Compaction pressure distribution and pressure uniformity of segmented rollers for automated fiber placement

For automated fiber placement onto molds with complex surfaces, uneven compaction pressure distribution limits tows number in a single sequence and affects layup quality. Compaction roller has a direct influence on the pressure distribution, but the relationship between the two has not been widely explored. In this paper, the segmented compaction roller is used, and a theoretical model of compaction pressure distribution for layup onto general surfaces is established by analyzing the contact between the roller and prepreg layers, followed by experimental validation. Based on the model, single-point pressure uniformity and whole-path pressure uniformity are proposed to quantitatively evaluate the pressure distribution. Furthermore, pressure distribution and pressure uniformity of segmented roller and common roller are compared, as well as the influence of the two pressure distribution on layup quality. The results show that the established model can predict pressure distribution and provide a basis for analyzing layup defects, and segmented rollers apply evener compaction pressure and help to improve layup quality.

Optimization of Kiel geometry for better recovery factor in high temperature measurement in aero gas turbine engine

During gas turbine engine testing, steady-state gas-path stagnation temperatures and pressures are measured in order to calculate the adiabatic efficiencies of the major turbomachinery components. These measurements are carried out using fixed intrusive probes, which are installed at the inlet and outlet of each component. The overall uncertainty in calculated component efficiency depends on the accuracy of discrete point pressure and temperature measurement. High accuracy in measurement and prediction of measurement errors has become increasingly important if small gains in component performance needs to be achieved. The recent trend is to predict component efficiencies within ±1–2%. The present work covers different Kiel designs that have been developed in a response to this demand based on a MATLAB code and experimental evaluation. A parametric study has been carried out by varying the two most critical parameters viz. Ae/Ab ratio and L/D ratio to optimize the Kiel design. These design changes will allow measurements to be made with minimum possible errors and efficiencies to be calculated more accurately over a wider range of conditions inside a low bypass turbofan gas turbine engine.

Influence of reservoir lithology on porous flow resistance of gas-bearing tight oil reservoirs and production forecast

The release of dissolved gas during the development of gas-bearing tight oil reservoirs has a great influence on the effect of development. In this article, the high-pressure mercury intrusion experiment was carried out in cores from different regions and lithologies of the Ordos Basin and the Sichuan Basin. The objectives are to study the microscopic characteristics of the porous throat structure of these reservoirs and to analyze the porous flow resistance laws of different lithology by conducting a resistance gradient test experiment. A mathematical model is established and the oil production index is corrected according to the experiment results to predict the oil production. The experimental results show that for tight reservoirs in the same area and lithology, the lower the permeability under the same back pressure, the greater the resistance gradient. And for sandstone reservoirs in different areas, the resistance gradients have little difference and the changes in the resistance coefficients are similar. However, limestone under the same conditions supports a much higher resistance gradient than sandstone reservoirs. Furthermore, the experimental results are consistent with the theoretical analysis indicating that the PVT (pressure–volume-temperature) characteristics in the nanoscale pores are different from those measured in the high-temperature, high-pressure sampler. Only when the pressure is less than a certain value of the bubble point pressure, the dissolved gas will begin to separate and generate resistance. This pressure is lower than the bubble point pressure measured in the high-temperature and pressure sampler. The calculation results show that the heterogeneity of limestone reservoirs and the mismatch of fluid storage and flow space will make the resistance, generated by the separation of dissolved gas, have a greater impact on oil production.