Advanced Well Completion Strategies to Improve Gas Production Deliverability in Marginal Tight Gas Reservoirs from an Onshore Abu Dhabi Gas Field

2021 ◽  
Author(s):  
Hajar Ali Abdulla Al Shehhi ◽  
Bondan Bernadi ◽  
Alia Belal Zuwaid Belal Al Shamsi ◽  
Shamma Jasem Al Hammadi ◽  
Fatima Omar Alawadhi ◽  
...  
Keyword(s):  
Hydraulic Fracturing ◽  
Horizontal Wells ◽  
Gas Production ◽  
Abu Dhabi ◽  
Tight Gas ◽  
Production Rates ◽  
Well Productivity ◽  
Gas Saturation ◽  
Well Design ◽  
The Impact

Abstract Reservoir X is a marginal tight gas condensate reservoir located in Abu Dhabi with permeability of less than 0.05 mD. The field was conventionally developed with a few single horizontal wells, though sharp production decline was observed due to rapid pressure depletion. This study investigates the impact of converting the existing single horizontal wells into single long horizontal, dual laterals, triple laterals, fishbone design and hydraulic fracturing in improving well productivity. The existing wells design modifications were planned using a near reservoir simulator. The study evaluated the impact of length, trajectory, number of laterals and perforation intervals. For Single, dual, and triple lateral wells, additional simulation study with hydraulic fracturing was carried out. To evaluate and obtain effective comparisons, sector models with LGR was built to improve the simulation accuracy in areas near the wellbore. The study conducted a detailed investigation into the impact of various well designs on the well productivity. It was observed that maximizing the reservoir contact and targeting areas with high gas saturation led to significant increase in the well productivity. The simulation results revealed that longer laterals led to higher gas production rates. Dual lateral wells showed improved productivity when compared to single lateral wells. This incremental gain in the production was attributed to increased contact with the reservoir. The triple lateral well design yielded higher productivity compared to single and dual lateral wells. Hydraulic fracturing for single, dual, and triple lateral wells showed significant improvement in the gas production rates and reduced condensate banking near the wellbore. A detailed investigation into the fishbone design was carried out, this involved running sensitivity runs by varying the number of branches. Fishbone design showed considerable increment in production when compared to other well designs This paper demonstrates that increasing the reservoir contact and targeting specific areas of the reservoir with high gas saturation can lead to significant increase in the well productivity. The study also reveals that having longer and multiple laterals in the well leads to higher production rates. Hydraulic fracturing led to higher production gains. Fishbone well design with its multiple branches showed the most production again when compared to other well designs.

Challenges to Geosteering and Completion Optimization of Horizontal Wells in the Cotton Valley Formation, East Texas

2015 ◽  
Vol 18 (04) ◽  
pp. 590-598
Author(s):  
S.. Liu ◽  
J. L. Lucas ◽  
P. A. Plemons ◽  
X.. Zhou ◽  
A.. Zett ◽  
...  
Keyword(s):  
Hydraulic Fracturing ◽  
Rock Type ◽  
Horizontal Wells ◽  
Gas Production ◽  
Tight Gas ◽  
East Texas ◽  
Log Data ◽  
Formation Evaluation ◽  
Tight Gas Sands ◽  
Cotton Valley

Summary Cotton Valley tight gas sands in the East Texas basin of North America consist of very-fine-grained, well-sorted quartz arenites and subarkoses that are overprinted by significant diagenetic processes. Stratigraphic variations in rock type control gas production. Hydraulic fracturing delivers economic gas production. We drilled horizontal wells more than 4,000 ft long consisting of more than 12 hydraulic-fracturing stages. The good gas-producing rock-type reservoirs are usually less than 14-ft thick and exhibit strong diagenetic overprint. Low gas prices challenge the use of sophisticated geosteering logs. By use of a very-basic gamma ray (GR) log and very-limited offset-pilot-well data, chasing such thin and variable sand bodies over a distance of 4,000 ft in a marginal marine sedimentary environment is daunting. Apart from this, horizontal wells that target thin layers present unique challenges to completion optimization. We acquired quad-combo log data, including azimuthal-density image data, by use of a logging-while-drilling (LWD) tool. We performed extensive log modeling by combining the horizontal well logs with logs from the two offset vertical wells, and achieved consistent interpretation. Log modeling has helped the post-drill well diagnosis in geosteering, completion design, and production performance. It has also supported formation evaluation. This study will highlight an integrated-study work flow in tight gas sands by use of openhole and cased-hole data. It will demonstrate the geosteering challenges, explain the log-modeling process, and display the formation-evaluation results. Geomechanical study, together with hydraulic-fracturing data and production-log data, will be used to confirm that good gas-producing rock types are easier to fracture, and they contribute better to production.

Advanced Multi-Disciplinary Simulation Workflow for Well Placement, Hydraulic Fracturing and Production Optimization Applied to the Diyab Unconventional Play in Onshore UAE

2021 ◽  
Author(s):  
Hamid Pourpak ◽  
Samuel Taubert ◽  
Marios Theodorakopoulos ◽  
Arnaud Lefebvre-Prudencio ◽  
Chay Pointer ◽  
...  
Keyword(s):  
Hydraulic Fracturing ◽  
United Arab Emirates ◽  
Reservoir Characterization ◽  
Horizontal Wells ◽  
Production Optimization ◽  
Production Performance ◽  
Well Placement ◽  
Fully Integrated ◽  
Sector Model ◽  
The Impact

Abstract The Diyab play is an emerging unconventional play in the Middle East. Up to date, reservoir characterization assessments have proved adequate productivity of the play in the United Arab Emirates (UAE). In this paper, an advanced simulation and modeling workflow is presented, which was applied on selected wells located on an appraisal area, by integrating geological, geomechanical, and hydraulic fracturing data. Results will be used to optimize future well landing points, well spacing and completion designs, allowing to enhance the Stimulated Rock Volume (SRV) and its consequent production. A 3D static model was built, by propagating across the appraisal area, all subsurface static properties from core-calibrated petrophysical and geomechanical logs which originate from vertical pilot wells. In addition, a Discrete Fracture Network (DFN) derived from numerous image logs was imported in the model. Afterwards, completion data from one multi-stage hydraulically fracked horizontal well was integrated into the sector model. Simulations of hydraulic fracturing were performed and the sector model was calibrated to the real hydraulic fracturing data. Different scenarios for the fracture height were tested considering uncertainties related to the fracture barriers. This has allowed for a better understanding of the fracture propagation and SRV creation in the reservoir at the main target. In the last step, production resulting from the SRV was simulated and calibrated to the field data. In the end, the calibrated parameters were applied to the newly drilled nearby horizontal wells in the same area, while they were hydraulically fractured with different completion designs and the simulated SRVs of the new wells were then compared with the one calculated on the previous well. Applying a fully-integrated geology, geomechanics, completion and production workflow has helped us to understand the impact of geology, natural fractures, rock mechanical properties and stress regimes in the SRV geometry for the unconventional Diyab play. This work also highlights the importance of data acquisition, reservoir characterization and of SRV simulation calibration processes. This fully integrated workflow will allow for an optimized completion strategy, well landing and spacing for the future horizontal wells. A fully multi-disciplinary simulation workflow was applied to the Diyab unconventional play in onshore UAE. This workflow illustrated the most important parameters impacting the SRV creation and production in the Diyab formation for he studied area. Multiple simulation scenarios and calibration runs showed how sensitive the SRV can be to different parameters and how well placement and fracture jobs can be possibly improved to enhance the SRV creation and ultimately the production performance.

Simultaneous Hydraulic Fracturing Improves Completion Efficiency and Lowers Costs Per Foot

2021 ◽  
Author(s):  
David Russell ◽  
Price Stark ◽  
Sean Owens ◽  
Awais Navaiz ◽  
Russell Lockman
Keyword(s):  
Hydraulic Fracturing ◽  
Oil And Gas ◽  
Horizontal Wells ◽  
Asset Returns ◽  
Gas Production ◽  
Well Performance ◽  
Additional Time ◽  
Oil And Gas Production ◽  
Single Well ◽  
Lateral Length

Abstract Reducing well costs in unconventional development while maintaining or improving production continues to be important to the success of operators. Generally, the primary drivers for oil and gas production are treatment fluid volume, proppant mass, and the number of stages or intervals along the well. Increasing these variables typically results in increased costs, causing additional time and complexity to complete these larger designs. Simultaneously completing two wells using the same volumes, rates, and number of stages as for any previous single well, allows for more lateral length or volume completed per day. This paper presents the necessary developments and outcomes of a completion technique utilizing a single hydraulic fracturing spread to simultaneously stimulate two or more horizontal wells. The goal of this technique is to increase operational efficiency, lower completion cost, and reduce the time from permitting a well to production of that well—without negatively impacting the primary drivers of well performance. To date this technique has been successfully performed in both the Bakken and Permian basins in more than 200 wells, proving its success can translate to other unconventional fields and operations. Ultimately, over 200 wells were successfully completed simultaneously, resulting in a 45% increase in completion speed and significant decrease in completion costs, while still maintaining equivalent well performance. This type of simultaneous completion scenario continues to be implemented and improved upon to improve asset returns.

Understanding Unusual Diagnostic Fracture Injection Test Results in Tight Gas Fields - A Holistic Approach to Resolving the Data

2015 ◽  
Author(s):  
R.N.. N. Naidu ◽  
E.A.. A. Guevara ◽  
A.J.. J. Twynam ◽  
J.. Rueda ◽  
W.. Dawson ◽  
...  
Keyword(s):  
Hydraulic Fracturing ◽  
Test Procedure ◽  
Holistic Approach ◽  
In Situ Stress ◽  
Lessons Learned ◽  
Petroleum Engineering ◽  
Tight Gas ◽  
Review Team ◽  
Gas Fields ◽  
The Impact

Abstract Hydraulic fracturing is a commonly used completion approach for extracting hydrocarbon resources from formations, particularly in those formations of very low permeability. As part of this process the use of Diagnostic Fracture Injection Tests (DFIT) can provide valuable information. When the measured pressures in such tests are outside the expected range for a given formation, a number of possibilities and questions will arise. Such considerations may include: What caused such inflated pressures? What is the in-situ stress state? Was there a mechanical or operational problem? Was the test procedure or the test equipment at fault? What else can explain the abnormal behaviour? While there may not be simple answers to all of these questions, such an experience can lead to a technically inaccurate conclusion based on inadequate analysis. A recently completed project faced just such a challenge, initially resulting in poor hydraulic fracturing efficiency and a requirement to understand the root causes. In support of this, a thorough analysis involving a multi-disciplinary review team from several technical areas, including petrophysics, rock/geo-mechanics, fluids testing/engineering, completions engineering, hydraulic fracture design and petroleum engineering, was undertaken. This paper describes the evolution of this study, the work performed, the results and conclusions from the analysis. The key factors involved in planning a successful DFIT are highlighted with a general template and a work process for future testing provided. The importance of appreciating the impact of the drilling and completion fluids composition, their properties and their compatibility with the formation fluids are addressed. The overall process and technical approach from this case study in tight gas fields, will have applicability across similar fields and the lessons learned could help unlock those reserves that are initially deemed technically or even commercially unattractive due to abnormal or unexpected behaviour measured during a DFIT operation.

Development of a new approach for hydraulic fracturing in tight sand with pre-existing natural fractures

2016 ◽  
Vol 56 (1) ◽  
pp. 225 ◽  
Author(s):  
Kunakorn Pokalai ◽  
David Kulikowski ◽  
Raymond L. Johnson ◽  
Manouchehr Haghighi ◽  
Dennis Cooke
Keyword(s):  
Hydraulic Fracturing ◽  
Hydraulic Fracture ◽  
High Stress ◽  
Gas Production ◽  
Natural Fracture ◽  
Rock Properties ◽  
Fracture Plane ◽  
Natural Fractures ◽  
Geomechanical Model ◽  
Well Design

Hydraulic fracturing in tight gas reservoirs has been performed in the Cooper Basin for decades in reservoirs containing high stress and pre-existing natural fractures, especially near faults. The hydraulic fracture is affected by factors such as tortuosity, high entry pressures, and the rock fabric including natural fractures. These factors cause fracture plane rotation and complexities, leading to fracture disconnection or reduced proppant placement during the treatment. In this paper, rock properties are estimated for a targeted formation using well logs to create a geomechanical model. Natural fracture and stress azimuths within the interval were interpreted from borehole image logs. The image log interpretations inferred that fissures are oriented 30–60° relative to the maximum horizontal stress. Next, diagnostic fracture injection test (DFIT) data was used with the poro-elastic stress equations to predict tectonic strains. Finally, the geomechanical model was history-matched with a planar 3D hydraulic fracturing simulator, and gave more insight into fracture propagation in an environment of pre-existing natural fractures. The natural fracture azimuths and calibrated geomechanical model are input into a framework to evaluate varying scenarios that might result based on a vertical or inclined well design. A well design is proposed based on the natural fracture orientation relative to the hydraulic fracture that minimises complexity to optimise proppant placement. In addition, further models and diagnostics are proposed to aid predicting the hydraulically induced fracture geometry, its impact on gas production, and optimising wellbore trajectory to positively interact with pre-existing natural fractures.

Geologic Controls on Gas Production and Hydraulic-Fracturing Flowback in Tight Gas Sandstones of the Late Jurassic Monteith Formation, Deep Basin, Alberta, Canada

2016 ◽  
Vol 19 (01) ◽  
pp. 024-040 ◽  
Author(s):  
Liliana Zambrano ◽  
Per K. Pedersen ◽  
Roberto Aguilera
Keyword(s):  
Hydraulic Fracturing ◽  
Gas Production ◽  
Production Performance ◽  
Rock Properties ◽  
Hydraulic Fractures ◽  
Tight Gas ◽  
Deep Basin ◽  
Rock Types ◽  
Sandstone Reservoirs ◽  
Geologic Controls

Summary A comparison of rock properties integrated with production performance and hydraulic-fracturing flowback (FB) of the uppermost lithostratigraphic “Monteith A” and the lowermost portion “Monteith C” of the Monteith Formation in the Western Canada Sedimentary Basin (WCSB) in Alberta is carried out with the use of existing producing gas wells. The analyses are targeted to understand the major geologic controls that differentiate the two tight gas sandstone reservoirs. This study consists of basic analytical tools available for geological characterization of tight gas reservoirs that is based on the identification and comparison of different rock types such as depositional, petrographic, and hydraulic for each lithostratigraphic unit of the Monteith Formation. As these low-matrix-permeability sandstone reservoirs were subjected to intense post-depositional diagenesis, a comparison of the various rock types allows the generation of more-accurate reservoir description, and a better understanding of the key geologic characteristics that control gas-production potential and possible impact on hydraulic-fracturing FB. Well performance and FB were the focus of many previous simulation and geochemical studies. In contrast, we find that an adequate understanding of the rocks hosting hydraulic fractures is a necessary complement to those studies for estimating FB times. This understanding was lacking in some previous studies. As a result, a new method is proposed on the basis of a crossplot of cumulative gas production vs. square root of time for estimating FB time. It is concluded that the “Monteith A” unit has better rock quality than the “Monteith C” unit because of less-heterogeneous reservoir geometry, less-complex mineralogical composition, and larger pore-throat apertures.

scholarly journals Chemical and bioassay assessment of waters related to hydraulic fracturing at a tight gas production site

2019 ◽  
Vol 690 ◽  
pp. 636-646
Author(s):  
Ann-Hélène Faber ◽  
Mark P.J.A. Annevelink ◽  
Paul P. Schot ◽  
Kirsten A. Baken ◽  
Merijn Schriks ◽  
...  
Keyword(s):  
Hydraulic Fracturing ◽  
Gas Production ◽  
Tight Gas ◽  
Production Site

Liquid loading in wellbores and its effect on cleanup period and well productivity in tight gas sand reservoirs

2010 ◽  
Vol 50 (1) ◽  
pp. 559
Author(s):  
Hassan Bahrami ◽  
M Reza Rezaee ◽  
Vamegh Rasouli ◽  
Armin Hosseinian
Keyword(s):  
Numerical Simulation ◽  
Gas Production ◽  
Production Performance ◽  
Tight Gas ◽  
Gas Reservoirs ◽  
Liquid Loading ◽  
Performance Modelling ◽  
Well Productivity ◽  
Tight Gas Reservoirs ◽  
Tight Gas Reservoir

Tight gas reservoirs normally have production problems due to very low matrix permeability and significant damage during well drilling, completion, stimulation and production. Therefore they might not flow gas to surface at optimum rates without advanced production improvement techniques. After well stimulation and fracturing operations, invaded liquids such as filtrate will flow from the reservoir into the wellbore, as gas is produced during well cleanup. In addition, there might be production of condensate with gas. The produced liquids when loaded and re-circulated downhole in wellbores, can significantly reduce the gas production rate and well productivity in tight gas formations. This paper presents assessments of tight gas reservoir productivity issues related to liquid loading in wellbores using numerical simulation of multiphase flow in deviated and horizontal wells. A field example of production logging in a horizontal well is used to verify reliability of the numerical simulation model outputs. Well production performance modelling is also performed to quantitatively evaluate water loading in a typical tight gas well, and test the water unloading techniques that can improve the well productivity. The results indicate the effect of downhole liquid loading on well productivity in tight gas reservoirs. It also shows how well cleanup is sped up with the improved well productivity when downhole circulating liquids are lifted using the proposed methods.

Tiltmeter Hydraulic Fracturing Mapping on a Cluster of Horizontal Wells in a Tight Gas Reservoir

2015 ◽  
Author(s):  
Jian Zhou ◽  
Yijin Zeng ◽  
Tingxue Jiang ◽  
Baoping Zhang ◽  
Xudong Zhang
Keyword(s):  
Hydraulic Fracturing ◽  
Horizontal Wells ◽  
Tight Gas ◽  
Gas Reservoir ◽  
Tight Gas Reservoir

scholarly journals Modeling Simultaneous Multiple Fracturing Using the Combined Finite-Discrete Element Method

Geofluids ◽  
2018 ◽  
Vol 2018 ◽  
pp. 1-20 ◽  
Author(s):  
Quansheng Liu ◽  
Lei Sun ◽  
Pingli Liu ◽  
Lei Chen
Keyword(s):  
Hydraulic Fracturing ◽  
Solid Phase ◽  
Horizontal Wells ◽  
In Situ Stress ◽  
Gas Production ◽  
Hydraulic Fractures ◽  
Multiple Fractures ◽  
Fracture Geometry ◽  
Stress Shadow ◽  
Oil Gas

Simultaneous multiple fracturing is a key technology to facilitate the production of shale oil/gas. When multiple hydraulic fractures propagate simultaneously, there is an interaction effect among these propagating hydraulic fractures, known as the stress-shadow effect, which has a significant impact on the fracture geometry. Understanding and controlling the propagation of simultaneous multiple hydraulic fractures and the interaction effects between multiple fractures are critical to optimizing oil/gas production. In this paper, the FDEM simulator and a fluid simulator are linked, named FDEM-Fluid, to handle hydromechanical-fracture coupling problems and investigate the simultaneous multiple hydraulic fracturing mechanism. The fractures propagation and the deformation of solid phase are solved by FDEM; meanwhile the fluid flow in the fractures is modeled using the principle of parallel-plate flow model. Several tests are carried out to validate the application of FDEM-Fluid in hydraulic fracturing simulation. Then, this FDEM-Fluid is used to investigate simultaneous multiple fractures treatment. Fractures repel each other when multiple fractures propagate from a single horizontal well, while the nearby fractures in different horizontal wells attract each other when multiple fractures propagate from multiple parallel horizontal wells. The in situ stress also has a significant impact on the fracture geometry.

Sign in / Sign up

Export Citation Format

Share Document