Carbonate oil and gas source rocks wettability alteration due to influence of polymer-colloidal drilling mud

Evaluation of rock wettability is an important task, since this parameter determines the distribution of water and oil in the reservoirs and their relative and phase permeability. The reliability of evaluation the wettability of rock samples depends on the drilling-in conditions during core sampling and core sample preparation methods. The investigation of the surface properties of the core from the Orenburg oil and gas condensate field showed that using of polymer-colloidal drilling mud leads to hydrophilization of the samples' surface. To obtain information on the actual wettability values of rock samples taken from wells drilled with polymer-colloidal drilling mud a method for estimating the relative (predominant) wettability of rocks based on petrophysical and lithological studies data is proposed. The authors suggest that the extraction of oil and gas source rock samples leads to irreversible changes in surface properties that cannot be restored. Keywords: selective wettability; relative wettability; predominant wettability; polymer-colloidal drilling mud; residual gas saturation; trapped gas saturation; pore space structure; extraction.

Study of the Critical Pore Radius That Results in Critical Gas Saturation during Methane Hydrate Dissociation at the Single-Pore Scale: Analytical Solutions for Small Pores and Potential Implications to Methane Production from Geological Media

We examine the critical pore radius that results in critical gas saturation during pure methane hydrate dissociation within geologic porous media. Critical gas saturation is defined as the fraction of gas volume inside a pore system when the methane gas phase spans the system. Analytical solutions for the critical pore radii are obtained for two, simple pore systems consisting of either a single pore-body or a single pore-body connected with a number of pore-throats. Further, we obtain critical values for pore sizes above which the production of methane gas is possible. Results shown in the current study correspond to the case when the depression of the dissociation temperature (due to the presence of small-sized pores; namely, with a pore radius of less than 100 nm) is considered. The temperature shift due to confinement in porous media is estimated through the well-known Gibbs-Thompson equation. The particular results are of interest to geological media and particularly in the methane production from the dissociation of natural hydrate deposits within off-shore oceanic or on-shore permafrost locations. It is found that the contribution of the depression of the dissociation temperature on the calculated values of the critical pore sizes for gas production is limited to less than 10% when compared to our earlier study where the porous media effects have been ignored.

Advanced Well Completion Strategies to Improve Gas Production Deliverability in Marginal Tight Gas Reservoirs from an Onshore Abu Dhabi Gas Field

Reservoir X is a marginal tight gas condensate reservoir located in Abu Dhabi with permeability of less than 0.05 mD. The field was conventionally developed with a few single horizontal wells, though sharp production decline was observed due to rapid pressure depletion. This study investigates the impact of converting the existing single horizontal wells into single long horizontal, dual laterals, triple laterals, fishbone design and hydraulic fracturing in improving well productivity. The existing wells design modifications were planned using a near reservoir simulator. The study evaluated the impact of length, trajectory, number of laterals and perforation intervals. For Single, dual, and triple lateral wells, additional simulation study with hydraulic fracturing was carried out. To evaluate and obtain effective comparisons, sector models with LGR was built to improve the simulation accuracy in areas near the wellbore. The study conducted a detailed investigation into the impact of various well designs on the well productivity. It was observed that maximizing the reservoir contact and targeting areas with high gas saturation led to significant increase in the well productivity. The simulation results revealed that longer laterals led to higher gas production rates. Dual lateral wells showed improved productivity when compared to single lateral wells. This incremental gain in the production was attributed to increased contact with the reservoir. The triple lateral well design yielded higher productivity compared to single and dual lateral wells. Hydraulic fracturing for single, dual, and triple lateral wells showed significant improvement in the gas production rates and reduced condensate banking near the wellbore. A detailed investigation into the fishbone design was carried out, this involved running sensitivity runs by varying the number of branches. Fishbone design showed considerable increment in production when compared to other well designs This paper demonstrates that increasing the reservoir contact and targeting specific areas of the reservoir with high gas saturation can lead to significant increase in the well productivity. The study also reveals that having longer and multiple laterals in the well leads to higher production rates. Hydraulic fracturing led to higher production gains. Fishbone well design with its multiple branches showed the most production again when compared to other well designs.

Characterization of a Volcanic Gas Reservoir Using Seismic Dispersion and Fluid Mobility Attributes

Seismic dispersion and fluid mobility attributes are used to characterize a volcanic gas reservoir in the Songliao Basin of China. A rock physics model is constructed to describe poroelastic behaviors associated with heterogeneous fluids saturation within the volcanic gas reservoirs, where velocity dispersion and attenuation of propagating waves are attributed to the wave-induced fluid flow described by the patchy saturation theory. Modeling results indicate that the frequency-dependent bulk modulus at the seismic frequency is more sensitive to gas saturation than the P-wave velocity dispersion. Accordingly, a new inversion method is developed to compute bulk-modulus-related dispersion attribute DK for improved characterization of volcanic gas reservoirs. Synthetic tests indicate that DK is more sensitive than traditional P-wave dispersion attribute DP to the variations of reservoir properties. The high value of dispersion attribute DK indicates the volcanic gas reservoirs with high porosity and gas saturation. At the same time, fluid mobility attribute FM can discriminate the volcanic gas reservoir as DK. Field data applications illustrate that DK and FM exhibit anomalies to the gas zones in the volcanic gas reservoir on the cross-well section. However, DK is more robust than FM to identify favorable zones on horizontal slices for specific target layers. Overall, rock physical modeling provides insights into the poroelastic behaviors of volcanic gas reservoirs, and inversion for seismic dispersion attribute DK improves hydrocarbon detection in the volcanic gas reservoir.

Developing features of the near-bottomhole zones in productive formations at fields with high gas saturation of formation oil

The article studies the formation features of the bottomhole zones in productive formations during operation of production wells in the north of the Perm Territory. Their distinctive feature is the high gas saturation of formation oil. The most widely used parameter in Russian and world practice – the skin factor was used as a criterion characterizing the state of the bottomhole zone. Analysis of scientific publications has shown that one of the main problems of applying the skin factor to assess the state of bottomhole zones is the ambiguity of interpretations of its physical meaning and the impossibility of identifying the prevailing factors that form its value. The paper proposes an approach to identifying such factors in the conditions of the fields under consideration, based on multivariate correlation-regression analysis. Choice of this tool is due to the complexity of the processes occurring in the “formation – bottomhole zone – well” system. When describing complex multifactorial processes, the chosen method demonstrates a high degree of reliability. For a large number of wells in the region, significant material was collected and summarized, including the results of determining the skin factor (1102 values) during hydrodynamic investigations, as well as data on the values ​​of various geological and technological indicators, which can probably be statistically related to the value of the skin factor. A series of multidimensional mathematical models has been built; the skin factor was used as a predicted parameter, and data on the values ​​of geological and technological indicators were used as independent indicators. Analysis of the constructed models is a key stage of this study. Set of parameters included in the multidimensional models, sequence of their inclusion and contribution to the total value of the achieved determination coefficient as the main indicator for the performance of the constructed models were studied. It has been established that the main factor influencing the state of the bottomhole zone is oil degassing. Significant differences in the formation features of the skin factor in the terrigenous and carbonate sediments at the fields under consideration have been determined.