Location of Semi-Rigid Connection Effect On The Seismic Performance of Steel Frame Structures

Author(s):  
Emad A. Elhout

Abstract In design steel frames, combining semi-rigid and rigid connections can result in better structural performance, particularly in seismic locations. In this study, the effects of semi-rigid beam-to-column connections located on the seismic performance of steel frame structures are investigated. The analysis uses six and twelve-story moment resisting steel frames (MRSF) with rigid, semi-rigid, and dual beam-column connections. These frames are designed according to the Egyptian design codes. Drain-2Dx computer program and seven earthquake ground motions are used in the non-linear dynamic analysis. The rotational stiffness of beam-to-column connections is indicated through the end fixity factors with a value equal to 0.6. The performances of these frames are evaluated through the roof drift ratio (RDR), the maximum story drift ratios (SDR), and the maximum column axial compression force (MACF). The results indicated that the quantities of fundamental periods, roof drift ratio, the story drift ratio, and the column axial compression force are related to stiffness, rigidity, and the number of semi-rigid connections in steel frames.

Author(s):  
Kensuke Shiomi

Through the 2011 Tohoku Earthquake or the 2016 Kumamoto Earthquake, much larger earthquakes are considered recently in the seismic designs of large steel-frame structures. When structures are exposed by these severe ground motions, partial destructions in the structures, such as damage or fracture of members could happen. Especially, the low cycle fatigue of steel structures because of the repeated load from these long-term ground motions is a serious problem. However, current seismic performance evaluation method based on nonlinear dynamic analysis considers only elastic and plastic deformation of each member, excluding the fracture of members. If this member fracture happens during earthquakes, there is considered to be many effects on the seismic performance, like the changes of the vibration property, the dynamic response and the energy absorbance capacity of structures. Therefore, the fracture of members is preferably taken into account in the seismic performance evaluation for these large earthquakes. This paper proposes the dynamic analysis method for steel-frame structures which can express the member fracture. Dynamic analyses considering and not considering member fracture under the repeated loads supposing the long-term earthquake are conducted to the FEM model of full-scale structure. By comparing each result, the effects of considering member fracture to the seismic performance such as the dynamic response and the energy absorbance capacity are discussed.


2018 ◽  
Vol 4 (1) ◽  
pp. 27
Author(s):  
Osman Fatih Bayrak ◽  
Seda Yedek ◽  
Muhammet Musab Erdem ◽  
Murat Bikce

Infill walls consisting of materials such as hollow concrete, hollow clay and autoclaved aerated concrete bricks are not only preferred in reinforced concrete buildings but also in steel frame structures. It is a well-known fact that infill walls limit the displacement of frames under horizontal loads. However, they may also bring about certain problems due to being placed randomly in horizontal and discontinuously in vertical directions for some architectural reasons. Moreover, cracks in frame-wall joints are observed in steel frame structures in which ductile behaving steel and brittle behaving infill walls are used together. In this study, the effect of infill walls on steel frames has been investigated. In the steel frame structure chosen for the study, four different situations consisting of different combinations of infill walls have been modeled by using ETABS Software. Later, the pushover analyses have been performed for all the models and their results have been compared. As a result of the analyses done by using the equivalent diagonal strut model, it has been found out that infill walls limit the displacement of steel frames and increase the performance of a structure. However, it has been also determined that in the steel frame structure in which the infill walls have been placed discontinuously in vertical and asymmetrically in horizontal, infill walls may lead to torsional and soft story irregularities. As a result, it is possible to observe cracks in the joints of infill walls and steel frame, the deformation properties of which differ, unless necessary precautions are taken.


2012 ◽  
Vol 166-169 ◽  
pp. 2373-2378
Author(s):  
He Tao Hou ◽  
Ming Lei Wu ◽  
Miao Liu ◽  
Qin Ma

In recent years, wall panels have been more and more used in the steel residential houses. A series of investigations on the seismic performance of the steel frame with composite panels have been carried out. According to the connection types between the steel frames and the panels, the structural system can be divided into two kinds: steel frames with hanging composite panels and steel frame infilled with composite panels. Results of all researchers revealed that the composite panels could effectively improve the lateral stiffness and bearing capacity of the steel frames, at the same time could enhance the energy dissipation capacity. Morever, in this paper, the relevant research results of connections between the steel frame and composite panels obtained are compared and discussed. This review provides helpful directions to those who are already engaged in composite panels used in the steel residential houses, and points out the simplified method needed to promote safe and economic use of composite panels.


2000 ◽  
Vol 3 (3) ◽  
pp. 215-229 ◽  
Author(s):  
Philip Avery ◽  
Mahen Mahendran

Application of “advanced analysis” methods suitable for non-linear analysis and design of steel frame structures permits direct and accurate determination of ultimate system strengths, without resort to simplified elastic methods of analysis and semi-empirical specification equations. However, the application of advanced analysis methods has previously been restricted to steel frames comprising only compact sections that are not influenced by the effects of local buckling. A research project has been conducted with the aim of developing concentrated plasticity methods suitable for practical advanced analysis of steel frame structures comprising non-compact sections. This paper contains a comprehensive set of analytical benchmark solutions for steel frames comprising non-compact sections, which can be used to verify the accuracy of simplified concentrated plasticity methods of advanced analysis. The analytical benchmark solutions were obtained using a distributed plasticity shell finite element model that explicitly accounts for the effects of gradual cross-sectional yielding, longitudinal spread of plasticity, initial geometric imperfections, residual stresses, and local buckling. A brief description and verification of the shell finite element model is provided in this paper.


Author(s):  
Kensuke Shiomi

Abstract For steel frame infrastructure facilities like thermal power plants, storage facilities or port facilities, the more advanced seismic performance is needed which not only prevent major damages against assumed design ground motions but also result in the “desirable failure mode” that concerns the recovery works or prevent from resulting in catastrophic failure mode, even under severe ground motions beyond design assumptions in which occurrence of some damages in structures are inevitable. “Seismic structures which can control the locations of failure of structural members inside structures” is one of the examples of this seismic performance. By adding this performance to steel frame structures at the stage of seismic design, the high resilience structures which concern recovery works after earthquakes can be realized. In this research, a basic study on the seismic performance which controls the locations of fractures of steel frame members by adjusting the cross sections of each structural member was carried out. The analytical studies about the design procedure to realize this seismic performance were conducted. Then, by conducting the shaking table tests for simple steel frame structures and confirming the location of fractures under dynamic loads, the possibility of this seismic performance was discussed experimentally.


Sign in / Sign up

Export Citation Format

Share Document