scholarly journals Effect of Chenodeoxycholic Acid as Dye Co-Adsorbent and ZnO Blocking Layer in Improving The Performance of Rose Bengal Dye Based Dye Sensitized Solar Cells

2021 ◽  
Author(s):  
Rajat Biswas ◽  
Suman Chatterjee
Keyword(s):  
Solar Cell ◽  
Chenodeoxycholic Acid ◽  
Short Circuit ◽  
Dye Sensitized Solar Cells ◽  
Short Circuit Current ◽  
Open Circuit ◽  
Blocking Layer ◽  
Cell Efficiency ◽  
Dye Sensitized ◽  
Dye Aggregation

Abstract Effective suppression of dye aggregation on the photoanode surface of dye sensitized solar cell plays a key role in improving the solar cell efficiency. Chenodeoxycholic acid (CDCA) is a very popular anti dye aggregation material used in Dye sensitized solar cells. However, the selection of an improper concentration of CDCA may lead to decreased solar cell efficiency by lowering the open circuit voltage and short circuit current as a consequence of reduced dye loading. The influence of chenodeoxycholic acid (CDCA) as a dye co-adsorbent on the performance of DSSCs fabricated using Rose Bengal dye was studied in this paper. The concentration of the CDCA solution was varied to identify the optimum value for the best device performance. Aside from this, the effect of a very thin and compact ZnO blocking layer was also investigated to reduce the recombination. With photovoltaic parameters such as short circuit current density (Jsc) = 1.98 mA/cm2, open circuit voltage (Voc) = 0.58 V, and fill factor (FF) = 0.43, the traditional cell displayed an overall conversion efficiency of 0.50 %, while the power conversion efficiency was found to be increased to 0.97 % ( Jsc = 2.80 mA/cm2, Voc= 0.64, FF = 0.58 ) when CDCA was added at optimised concentration of 8 mM. Reduced dye aggregation and increased electron injection in the presence of CDCA may be accounted for the DSSC's remarkable improvement in efficiency. Moreover, the combined effect of 8 mM CDCA and the compact ZnO blocking layer dramatically enhanced the efficiency further to 1.23 % (Jsc = 3.09 mA/cm2, Voc= 0.66, FF = 60 ). Electrochemical impedance spectroscopic (EIS) analysis revealed that the addition of CDCA as a co-adsorbent in the dye solution and addition of ZnO blocking layer resulted in significantly improved electron lifetime and reduced electron recombination yielding improved Jsc, Voc and η.

Characteristics of Dye-Sensitized Solar Cells Using Dye from Pitaya Fruit

2015 ◽  
Vol 793 ◽  
pp. 450-454 ◽  
Author(s):  
N. Gomesh ◽  
R. Syafinar ◽  
Muhamad Irwanto ◽  
Y.M. Irwan ◽  
M. Fareq ◽  
...  
Keyword(s):  
Solar Cell ◽  
Short Circuit ◽  
Dye Sensitized Solar Cells ◽  
Short Circuit Current ◽  
Liquid Electrolyte ◽  
Open Circuit ◽  
Dye Sensitized Solar Cell ◽  
Photoelectrochemical Performance ◽  
Cell Efficiency ◽  
Dye Sensitized

Dye-sensitized solar cell (DSSC) consists of TiO2 nanoporous coating which acts as a photo electrode, a sensitizer of dye molecules soaked in the TiO2 film, liquid electrolyte and a counter electrode. This paper focuses on the usage of a sensitizer from the Pitaya fruit. Pitaya or commonly known as dragon fruit (Hylocereus polyrhizus) was extracted and used as a sensitizer to fabricate the dye sensitized solar cell (DSSC). The photoelectrochemical performance of Pitaya based solar cell shows an open circuit voltage (VOC) of 237 mV, short circuit current (ISC) of 4.98 mA, fill factor (FF) of 0.51, solar cell efficiency (η) of 0.70 % and has a peak absorbance rate of 2.7 at 550 nm. The photoelectrochemical and UV-Visible light absorbance performance of Pitaya-DSSC shows good potential in future solar cell fabrication.

scholarly journals Magnetron Sputtered Electron Blocking Layer as an Efficient Method to Improve Dye-Sensitized Solar Cell Performance

Energies ◽  
2020 ◽  
Vol 13 (11) ◽  
pp. 2690
Author(s):  
Dariusz Augustowski ◽  
Paweł Kwaśnicki ◽  
Justyna Dziedzic ◽  
Jakub Rysz
Keyword(s):  
Solar Cell ◽  
Short Circuit ◽  
Dye Sensitized Solar Cells ◽  
Short Circuit Current ◽  
Dye Sensitized Solar Cell ◽  
Blocking Layer ◽  
Electron Blocking Layer ◽  
Solar Cell Performance ◽  
Force Microscopy ◽  
Dye Sensitized

The main efficiency loss is caused by an intensive recombination process at the interface of fluorine-doped tin oxide (FTO) and electrolyte in dye-sensitized solar cells. Electrons from the photoanode can be injected back to the redox electrolyte and, thus, can reduce the short circuit current. To avoid this, the effect of the electron blocking layer (EBL) was studied. An additional thin film of magnetron sputtered TiO2 was deposited directly onto the FTO glass. The obtained EBL was characterized by atomic force microscopy, scanning electron microscopy, optical profilometry, energy dispersive spectroscopy, Raman spectroscopy and UV-VIS-NIR spectrophotometry. The results of the current–voltage characteristics showed that both the short circuit current (Isc) and fill factor (FF) increased. Compared to traditional dye-sensitized solar cell (DSSC) architecture, the power conversion efficiency (η) increased from 4.67% to 6.07% for samples with a 7 × 7 mm2 active area and from 2.62% to 3.06% for those with an area of 7 × 80 mm2.

scholarly journals Efficiency enhancement of natural dye sensitized solar cell by optimizing electrode fabrication parameters

2018 ◽  
Vol 35 (4) ◽  
pp. 816-823 ◽  
Author(s):  
M. Khalid Hossain ◽  
M.F. Pervez ◽  
S. Tayyaba ◽  
M. Jalal Uddin ◽  
A.A. Mortuza ◽  
...  
Keyword(s):  
Solar Cell ◽  
Counter Electrode ◽  
Short Circuit ◽  
Short Circuit Current ◽  
Short Circuit Current Density ◽  
Open Circuit ◽  
Dye Sensitized Solar Cell ◽  
Cell Efficiency ◽  
Dye Sensitized ◽  
Candle Flame

Abstract Efficiency of dye-sensitized solar cell (DSSC) depends on several interrelated factors such as type and concentration of dye, type and thickness of photoelectrode and counter electrode. Optimized combination of these factors leads to a more efficient cell. This paper presents the effect of these parameters on cell efficiency. TiO2 nanoporous thin films of different thicknesses (5 μm to 25 μm) were fabricated on indium doped tin oxide (ITO) coated glass by doctor blading method and characterized by inverted microscope, stylus surface profiler and scanning electron microscope (SEM). Natural organic dye of different concentrations, extracted from turmeric, was prepared with ethanol solvent. Different combinations of dye concentrations and film thicknesses along with different types of carbon catalyst have been investigated by I-V characterization. The result shows that the cell made of a counter electrode catalyst material prepared by candle flame carbon combined with about 15 μm thick photoelectrode and 100 mg/mL dye in ethanol solvent, achieves the highest efficiency of 0.45 %, with open circuit voltage of 566 mV and short circuit current density of 1.02 mA/cm2.

Characterization of Dye-Sensitized Solar Cell with Different Nanoparticle sizes

2011 ◽  
Vol 1322 ◽  
Author(s):  
Aung Htun ◽  
Lakshmi V. Munukutla ◽  
Sailaja Radhakrishnan ◽  
Chih Y. Jen ◽  
Arunachalanadar M. Kannan ◽  
...  
Keyword(s):  
Solar Cell ◽  
Layer Thickness ◽  
Short Circuit ◽  
Short Circuit Current ◽  
Open Circuit ◽  
Nanoparticle Size ◽  
Cell Efficiency ◽  
Dye Sensitized ◽  
20 Nm ◽  
Nanoparticle Sizes

ABSTRACTThe Dye-sensitized Solar Cell (DSSC) has been regarded as the next-generation solar cell because of its simple and low cost fabrication process. The experiments for optimizing the cell efficiency were carried out in this work include varying the TiO2 layer thickness on the working electrode and determining the most favorable nanoparticle size in the TiO2 paste. The TiO2 electrode or working electrode was fabricated using screen printing technique with the Coatema tool with thicknesses ranging from ~20 to 66 μm. It was observed that both open circuit voltage and short circuit current were found to have measurable dependence on the TiO2 layer thickness. The open circuit voltage changed from 0.77 to 0.82 V and correspondingly the short circuit current also varied from ~19 to 23 mA/cm2 depending on the TiO2 layer thickness. Additionally, the cell with 40 μm TiO2 thickness showed 9.06% photo conversion efficiency compared to 6.4% and 8.5% efficiency obtained for the cells with 20 μm and 66 μm TiO2 thicknesses respectively. The second part of the experiment was conducted using three different nanoparticle sizes of 13 nm, 20 nm and 37nm in the TiO2 layer to identify optimum nanoparticle size by maintaining the TiO2 film thickness at 40 μm. The cell with 20 nm size nanoparticle, in combination with 40 μm TiO2 thickness showed 11.2% efficiency that is in par or slightly better than the efficiency value reported for the DSSC in the literature as of now. The work described in this paper showed best possible values for the TiO2 layer thickness and nanoparticle size in the TiO2 for obtaining improved cell efficiency of 11.2%.

scholarly journals Development of pma/pvac-tpai-bmii solid polymer electrolytes for application in dye sensitized solar cell

2018 ◽  
Vol 67 ◽  
pp. 03032
Author(s):  
Amisha Azmar ◽  
Tan Winie
Keyword(s):  
Relaxation Time ◽  
Solar Cell ◽  
Short Circuit ◽  
Dye Sensitized Solar Cells ◽  
Short Circuit Current ◽  
Open Circuit ◽  
Solid Polymer Electrolytes ◽  
Solid Polymer ◽  
Casting Technique ◽  
Dye Sensitized

Electrolyte film of poly(methyl acrylate) (PMA) and poly(vinyl acetate) (PVAc) with composition of 90:10 and 20 wt.% of tetrapropyl ammonium iodide (TPAI) at different of 1-butyl-3- methyl imidazoliumiodide (BMII) concentration were prepared by solution casting technique. Highest conductivities achieve at 5wt.% of BMII is 1.2 x 10-11 S cm-1. Effects of temperature of this sample on the dielectric properties was studied by impedance spectroscopy. The dielectric constant, εr and dielectric loss, εi increased with increasing temperature. Charge carrier relaxation time was extracted from the electrical modulus spectra. It was found that the relaxation time decreased with temperature. The ac conductivity was observed to obey the Jonscher’s Universal Power Law. The correlated barrier hopping model (CBH) was used to interpret the conduction mechanism of the present electrolyte system. Electrolyte films were sandwiched between titanium dioxide photoanode and platinum counter electrode for dye-sensitized solar cells (DSSCs) assembly. The solar cell with 5wt.% showed highest efficiency of 4.62% with maximum short circuit current density(Jsc) of 10.04 mAcm-2, open circuit voltage (Voc) 0.70 V and fill factor, ff of 66.04%.

scholarly journals Control of Porphyrin Dye Aggregation Using Bis(4-pyridyl)Alkanes in Dye Sensitized Solar Cells

2019 ◽  
pp. 63
Author(s):  
B. Baptayev ◽  
A. Rysbekova ◽  
D. Kalpakov ◽  
A. Aukenova ◽  
D. Mustazheb ◽  
...  
Keyword(s):  
Solar Cells ◽  
Short Circuit ◽  
Photovoltaic Performance ◽  
Dye Sensitized Solar Cells ◽  
Short Circuit Current ◽  
Short Circuit Current Density ◽  
Cell Efficiency ◽  
Dye Sensitized ◽  
Dye Aggregation ◽  
Sensitized Solar Cells

The aggregation of sensitizer molecules on the surface of photoanode is a serious issue that can affect the photovoltaic performance of dye-sensitized solar cells. Prevention of dye agglomeration, therefore, is critical. Traditional methods of aggregation control are either synthetically challenging or technologically difficult and expensive. In this article, the use of bis(4-pyridyl)alkanes to control porphyrin dye aggregation is presented. Three bis(4-pyridyl)alkanes – bis(4-pyridyl)butane L4, bis(4-pyridyl)octane L8 and bis(4-pyridyl)decane L10 were synthesized. These bis(4-pyridyl)alkane ligands are axially attached to the metallic center of synthesized porphyrin dye P. The complexes was obtained by mixing the solutions of dye P and each ligand (L) in 2:1 ratio 1 h before the soaking step. As a result three cells were prepared: P-L4, P-L8 and P-L10. The performance of these cells were compared with a reference cell which was prepared from porphyrin dye P only. IPCE analysis demonstrated the highest dye load in P-L4 cell which was ascribed to lowered dye aggregation. Photovoltaic analysis showed improved short circuit current density due to suppressed dye aggregation caused by the complexation of the porphyrin dye P with the linker L4. As a result the overall cell efficiency increased to 42% demonstrating the successful utilization of the (4-pyridyl)alkane linker complexes with porphyrin dye.

scholarly journals CdTe-Based Thin Film Solar Cells: Past, Present and Future

Energies ◽  
2021 ◽  
Vol 14 (6) ◽  
pp. 1684
Author(s):  
Alessandro Romeo ◽  
Elisa Artegiani
Keyword(s):  
Thin Film ◽  
Solar Cells ◽  
Solar Cell ◽  
Short Circuit ◽  
Short Circuit Current ◽  
Short Circuit Current Density ◽  
Open Circuit ◽  
Early Years ◽  
Solar Cell Efficiency ◽  
Cell Efficiency

CdTe is a very robust and chemically stable material and for this reason its related solar cell thin film photovoltaic technology is now the only thin film technology in the first 10 top producers in the world. CdTe has an optimum band gap for the Schockley-Queisser limit and could deliver very high efficiencies as single junction device of more than 32%, with an open circuit voltage of 1 V and a short circuit current density exceeding 30 mA/cm2. CdTe solar cells were introduced at the beginning of the 70s and they have been studied and implemented particularly in the last 30 years. The strong improvement in efficiency in the last 5 years was obtained by a new redesign of the CdTe solar cell device reaching a single solar cell efficiency of 22.1% and a module efficiency of 19%. In this paper we describe the fabrication process following the history of the solar cell as it was developed in the early years up to the latest development and changes. Moreover the paper also presents future possible alternative absorbers and discusses the only apparently controversial environmental impacts of this fantastic technology.

IMPROVING STABILITY OF CHLOROPHYLL AS NATURAL DYE FOR DYE-SENSITIZED SOLAR CELLS

2017 ◽  
Vol 80 (1) ◽  
Author(s):  
Zainal Arifin ◽  
Sudjito Soeparman ◽  
Denny Widhiyanuriyawan ◽  
Suyitno Suyitno ◽  
Argatya Tara Setyaji
Keyword(s):  
Current Density ◽  
Open Circuit Voltage ◽  
Short Circuit ◽  
Dye Sensitized Solar Cells ◽  
Short Circuit Current ◽  
Short Circuit Current Density ◽  
Open Circuit ◽  
Natural Dyes ◽  
Dye Sensitized ◽  
Sensitized Solar Cells

Natural dyes have attracted much researcher’s attention due to their low-cost production, simple synthesis processes and high natural abundance. However the dye-sensitized solar cells (DSSCs) based natural dyes have higher tendency to degradation. This article reports on the enhancement of performance and stability of dye-sensitized solar cells (DSSCs) using natural dyes. The natural dyes were extracted from papaya leaves by ethanol solvent at a temperature of 50 °C. Then the extracted dyes were isolated and modified into Mg-chlorophyll using column chromatography. Mg-chlorophyll was then synthesized into Fe-chlorophyll to improve stability. The natural dyes were characterized using ultraviolet-visible spectrometry, Fourier transform infrared spectroscopy, and cyclic voltammetry. The performance of DSSCs was tested using a solar simulator. The results showed the open-circuit voltage, the short-circuit current density, and the efficiency of the extracted papaya leaves-based DSSCs to be 325 mV, 0.36 mA/cm2, and 0.07%, respectively. Furthermore, the DSSCs with purified chlorophyll provide high open-circuit voltage of 425 mV and short-circuit current density of 0.45 mA/cm2. The use of Fe-chlorophyll for sensitizing the DSSCs increases the efficiency up to 2.5 times and the stability up to two times. The DSSCs with Fe-chlorophyll dyes provide open-circuit voltage, short-circuit current density, and efficiency of 500 mV, 0.62 mA/cm2, and 0.16%, respectively. Further studies to improve the current density and stability of natural dye-based DSSCs along with an improvement in the anchor between dyes and semiconducting layers are required.

Inkjet Printing Technology for Dye-Sensitized Solar Cells

2012 ◽  
Vol 476-478 ◽  
pp. 1767-1770
Author(s):  
Yu Li Lin ◽  
Cheng Yi Hsu ◽  
Chang Lun Tai
Keyword(s):  
Open Circuit Voltage ◽  
Short Circuit ◽  
Dye Sensitized Solar Cells ◽  
Short Circuit Current ◽  
Open Circuit ◽  
Dye Sensitized ◽  
Tio2 Particles ◽  
Ito Glass ◽  
Sensitized Solar Cells ◽  
Pet Substrate

The task of this study is to prepare the TiO2 film electrode for dye-sensitized solar cells (DSSC) on ITO PET substrate using a general jet-printer. The results were compared with that obtained using ITO glass substrate. In this study, the dispersion of TiO2 slurry was manipulated by changing the pH value of the solution to avoid agglomeration of TiO2 particles. The average TiO2 particles used in this study were measured about 130nm. The experimental results show that it has the best performance when the thickness of the TiO2 film was about 10μm. In ITO glass substrate, the measured short circuit current was about 5.03mA, the open circuit voltage was measured to be 0.65V. In ITO-PET substrate, the measured short circuit current was about 2.73mA, the open circuit voltage was measured to be 0.68V.

scholarly journals Prunus domestica dye extraction for fabrication of zinc oxide based dye-sensitized solar cells

BIBECHANA ◽  
2015 ◽  
Vol 13 ◽  
pp. 23-28
Author(s):  
Leela Pradhan Joshi
Keyword(s):  
Zinc Oxide ◽  
Solar Cells ◽  
Short Circuit ◽  
Dye Sensitized Solar Cells ◽  
Short Circuit Current ◽  
Zinc Nitrate ◽  
Open Circuit ◽  
Dye Sensitized ◽  
Dye Extraction ◽  
Sensitized Solar Cells

Aluminium doped Zinc Oxide (AZO) seed layers were deposited on Fluorine doped Tin Oxide (FTO) substrates using a spin coating technique. These were then immersed in growth solutions of zinc nitrate, hexamethylenetetramine and distilled water to develop nanoplates of Zinc Oxide (ZnO). The nanostructures of ZnO grown on FTO were studied using x-ray diffraction techniques. Dye-sensitized solar cells (DSSC) were fabricated using two prepared electrodes, one of dye-loaded zinc oxide and another that was platinum coated. The electrolyte used was potassium iodide iodine solution. The performance of the assembled DSCCs was tested by drawing an IV curve. The results showed that the short circuit current and open circuit voltages were about 10 microamperes and 270 millivolts respectively.BIBECHANA 13 (2016) 23-28

Sign in / Sign up

Export Citation Format

Share Document