Processing, Structure and Properties of Heavily Deformed in Situ Composites.

1987 ◽  
Author(s):  
T. H. Courtney ◽  
J. K. Lee
Keyword(s):  
Structure And Properties ◽  
In Situ Composites

Fabrication, characterization and analysis of improvements in mechanical properties of AA7075/ZrB2 in-situ composites

Measurement ◽  
2019 ◽  
Vol 136 ◽  
pp. 356-366 ◽  
Author(s):  
M. Nallusamy ◽  
S. Sundaram ◽  
K. Kalaiselvan
Keyword(s):  
Mechanical Properties ◽  
In Situ Composites

scholarly journals Microcantilever Fracture Tests on Eutectic NiAl–Cr(Mo) In Situ Composites

2021 ◽  
pp. 2001464
Author(s):  
Stefan Gabel ◽  
Sven Giese ◽  
Benoit Merle ◽  
Ioannis Sprenger ◽  
Martin Heilmaier ◽  
...  
Keyword(s):  
In Situ Composites ◽  
Fracture Tests

Manufacture and Microstructures of Fe-Cr-C Hypereutectic In Situ Composites

2007 ◽  
Vol 336-338 ◽  
pp. 1406-1408 ◽  
Author(s):  
Xiao Hui Zhi ◽  
Jian Dong Xing ◽  
Yi Min Gao ◽  
Xiao Jun Wu ◽  
Xiao Le Cheng
Keyword(s):  
Hypereutectic Alloy ◽  
Reinforced Composites ◽  
In Situ Composites ◽  
In Situ Composite ◽  
Particle Reinforced Composites ◽  
Primary Carbides

In the present study, a Fe-Cr-C hypereutectic alloy was prepared from industry-grade materials and subjected to modification and fluctuation, through which new types of particle reinforced composites, hypereutectic in-situ composite, was generated. The structures of the composite modified or not with the range of fluctuation addition from 0% to 2.8wt.%, were investigated. The primary carbides were refined with the addition of modifying agents and fluctuations. Increasing the amount of fluctuation resulted in finer primary carbides. At 1380oC, with the addition of modifying agents and 2.8wt.% fluctuation addition, the structure was well modified.

Microstructural characterization and mechanical properties of Nb–Ti–C–B in-situ composites with W addition

2015 ◽  
Vol 646 ◽  
pp. 332-340 ◽  
Author(s):  
Xinjiang Zhang ◽  
Yibin Li ◽  
Xiaodong He ◽  
Xueran Liu ◽  
Qiong Jiang ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Microstructural Characterization ◽  
In Situ Composites

Mechanical properties of NiAl-Mo composites produced by specially controlled directional solidification

2012 ◽  
Vol 1516 ◽  
pp. 255-260 ◽  
Author(s):  
G. Zhang ◽  
L. Hu ◽  
W. Hu ◽  
G. Gottstein ◽  
S. Bogner ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Fracture Toughness ◽  
Directional Solidification ◽  
Creep Resistance ◽  
Room Temperature ◽  
Growth Direction ◽  
Nominal Composition ◽  
Potential Candidate ◽  
In Situ Composites

ABSTRACTMo fiber reinforced NiAl in-situ composites with a nominal composition Ni-43.8Al-9.5Mo (at.%) were produced by specially controlled directional solidification (DS) using a laboratory-scale Bridgman furnace equipped with a liquid metal cooling (LMC) device. In these composites, single crystalline Mo fibers were precipitated out through eutectic reaction and aligned parallel to the growth direction of the ingot. Mechanical properties, i.e. the creep resistance at high temperatures (HT, between 900 °C and 1200 °C) and the fracture toughness at room temperature (RT) of in-situ NiAl-Mo composites, were characterized by tensile creep (along the growth direction) and flexure (four-point bending, vertical to the growth direction) tests, respectively. In the current study, a steady creep rate of 10-6s-1 at 1100 °C under an initial applied tensile stress of 150MPa was measured. The flexure tests sustained a fracture toughness of 14.5 MPa·m1/2at room temperature. Compared to binary NiAl and other NiAl alloys, these properties showed a remarkably improvement in creep resistance at HT and fracture toughness at RT that makes this composite a potential candidate material for structural application at the temperatures above 1000 °C. The mechanisms responsible for the improvement of the mechanical properties in NiAl-Mo in-situ composites were discussed based on the investigation results.

Processing high-temperature refractory-metal silicide in-situ composites

JOM ◽  
1999 ◽  
Vol 51 (4) ◽  
pp. 32-36 ◽  
Author(s):  
B. P. Bewlay ◽  
M. R. Jackson ◽  
P. R. Subramanian
Keyword(s):  
High Temperature ◽  
Refractory Metal ◽  
Metal Silicide ◽  
In Situ Composites
Sign in / Sign up

Export Citation Format

Share Document