scholarly journals THE EFFICACY OF LASER GLAZING ON SURFACE ROUGHNESS AND STRUCTURE OF ALL-CERAMIC VENEERS

2016 ◽  
Vol 62 (1) ◽  
pp. 1089-1096
Author(s):  
Sara Hegazy ◽  
Azza Hashem ◽  
Shaymaa Habib
Keyword(s):  
Surface Roughness ◽  
Laser Glazing ◽  
All Ceramic

Influence of Silane Treatment of All-Ceramic Surfaces (e-Max) on the Cementation with Tooth Dentine

2017 ◽  
Vol 758 ◽  
pp. 34-38
Author(s):  
Evangelos Gkogkas ◽  
Panagiota T. Dalla ◽  
Theodore E. Matikas ◽  
Simeon Agathopoulos
Keyword(s):  
Surface Roughness ◽  
Electron Microscope ◽  
Glass Ceramic ◽  
Deep Understanding ◽  
Prolonged Treatment ◽  
Silane Treatment ◽  
Atomic Force ◽  
Ceramic Surfaces ◽  
All Ceramic ◽  
Scanning Electron

The influence of the treatment of the surface of IPS Empress II (e-max) glass-ceramic dental material with different silane agents on the surface roughness of this glass-ceramic was evaluated. IPS Empress II (e-max) cores were treated with five different commercial silane agents used in dentistry nowadays, for several periods of time and were finally air dried. After silanization, the surfaces of the glass-ceramic cores were observed with a light profilometer, a scanning electron microscope (SEM), and an atomic force microscope (AFM). The values of surface roughness (Ra) were also measured with the light profilometer. The results showed an important effect of silane treatment applied for different periods of time, especially for prolonged treatment for 24 hours, on the surface roughness of IPS Empress II (e-max). These results can have an important impact on the deep understanding of the cementation protocols applied in modern dentistry.

HREM interface studies in SiC-whisker-reinforced Al2O3 and Si3N4 ceramics

1988 ◽  
Vol 46 ◽  
pp. 734-735
Author(s):  
W. Braue ◽  
R.W. Carpenter ◽  
D.J. Smith
Keyword(s):  
Analytical Data ◽  
Base Material ◽  
High Strength ◽  
Ceramic Composites ◽  
Good Thermal Stability ◽  
All Ceramic ◽  
Sic Whiskers ◽  
Base Composite ◽  
C 30 ◽  
Si3n4 Ceramics

Whisker and fiber reinforcement has been established as an effective toughening concept for monolithic structural ceramics to overcome limited fracture toughness and brittleness. SiC whiskers in particular combine both high strength and elastic moduli with good thermal stability and are compatible with most oxide and nonoxide matrices. As the major toughening mechanisms - crack branching, deflection and bridging - in SiC whiskenreinforced Al2O3 and Si3N41 are critically dependent on interface properties, a detailed TEM investigation was conducted on whisker/matrix interfaces in these all-ceramic- composites.In this study we present HREM images obtained at 400 kV from β-SiC/α-Al2O3 and β-SiC/β-Si3N4 interfaces, as well as preliminary analytical data. The Al2O3- base composite was hotpressed at 1830 °C/60 MPa in vacuum and the Si3N4-base material at 1725 °C/30 MPa in argon atmosphere, respectively, adding a total of 6 vt.% (Y2O3 + Al2O3) to the latter to promote densification.

Biomimetic materials: An introduction

1992 ◽  
Vol 50 (2) ◽  
pp. 1020-1021 ◽  
Author(s):  
M. Sarikaya ◽  
J. T. Staley ◽  
I. A. Aksay
Keyword(s):  
Self Assembly ◽  
Structural Control ◽  
Hierarchical Structures ◽  
Ceramic Composites ◽  
Advanced Materials ◽  
Length Scale ◽  
Spider Webs ◽  
Biomimetic Materials ◽  
Synthetic Materials ◽  
All Ceramic

Biomimetics is an area of research in which the analysis of structures and functions of natural materials provide a source of inspiration for design and processing concepts for novel synthetic materials. Through biomimetics, it may be possible to establish structural control on a continuous length scale, resulting in superior structures able to withstand the requirements placed upon advanced materials. It is well recognized that biological systems efficiently produce complex and hierarchical structures on the molecular, micrometer, and macro scales with unique properties, and with greater structural control than is possible with synthetic materials. The dynamism of these systems allows the collection and transport of constituents; the nucleation, configuration, and growth of new structures by self-assembly; and the repair and replacement of old and damaged components. These materials include all-organic components such as spider webs and insect cuticles (Fig. 1); inorganic-organic composites, such as seashells (Fig. 2) and bones; all-ceramic composites, such as sea urchin teeth, spines, and other skeletal units (Fig. 3); and inorganic ultrafine magnetic and semiconducting particles produced by bacteria and algae, respectively (Fig. 4).

Roughness measurements of nonlinear optical polymer films by scanning tunneling microscopy

1989 ◽  
Vol 47 ◽  
pp. 22-23
Author(s):  
I. H. Musselman ◽  
R.-T. Chen ◽  
P. E. Russell
Keyword(s):  
Surface Roughness ◽  
Scanning Tunneling Microscopy ◽  
Nonlinear Optical ◽  
Polymer Surface ◽  
Light Extinction ◽  
Scanning Tunneling ◽  
Silicon Substrates ◽  
Tunneling Microscopy ◽  
Optical Polymer ◽  
Total Light

Scanning tunneling microscopy (STM) has been used to characterize the surface roughness of nonlinear optical (NLO) polymers. A review of STM of polymer surfaces is included in this volume. The NLO polymers are instrumental in the development of electrooptical waveguide devices, the most fundamental of which is the modulator. The most common modulator design is the Mach Zehnder interferometer, in which the input light is split into two legs and then recombined into a common output within the two dimensional waveguide. A π phase retardation, resulting in total light extinction at the output of the interferometer, can be achieved by changing the refractive index of one leg with respect to the other using the electrooptic effect. For best device performance, it is essential that the NLO polymer exhibit minimal surface roughness in order to reduce light scattering. Scanning tunneling microscopy, with its high lateral and vertical resolution, is capable of quantifying the NLO polymer surface roughness induced by processing. Results are presented below in which STM was used to measure the surface roughness of films produced by spin-coating NLO-active polymers onto silicon substrates.

Sign in / Sign up

Export Citation Format

Share Document