Upgrading of existing aerobic plants with the LUCAS anaerobic system based on full-scale experiences

2005 ◽  
Vol 52 (4) ◽  
pp. 39-46 ◽  
Author(s):  
R. Gerards ◽  
W. Gils ◽  
L. Vriens
Keyword(s):  
Full Scale ◽  
Upflow Anaerobic Sludge Blanket ◽  
Uasb Reactor ◽  
Organic Loading Rate ◽  
Anaerobic Sludge ◽  
Aerobic Treatment ◽  
Treatment Efficiency ◽  
Nitrogen And Phosphorus ◽  
Anaerobic Sludge Blanket ◽  
Sludge Production

It has been demonstrated that the combination of anaerobic–aerobic treatment is the best technological and economical solution for the treatment of high loaded wastewater. Where in the past aerobic treatment systems were still very acceptable due to the very good treatment efficiency, simplicity and robustness of the technology, this has, in most cases, been changed due to very stringent sludge disposal legislation. The anaerobic pretreatment takes care of approximately 80–90% of the overall treatment efficiency at high loading rates and low sludge production and low energy costs. The aerobic posttreatment takes care of the absolute high removal efficiency and nitrogen and phosphorus removal. Because of the low organic loading rate of the aerobic posttreatment also in this stage the sludge production is low. The combination of anaerobic–aerobic treatment results in a compact system capable of reaching high treatment efficiency at low sludge production and lower energy consumption. Waterleau Global Water Technology has developed LUCAS® anaerobic–aerobic system that combines an Upflow Anaerobic Sludge Blanket (UASB) reactor with an aerobic, constant-level cyclic activated sludge system, which is very suitable for the treatment of high loaded wastewaters in general and brewery waste water in particular. It has been proven from several full scale upgrading projects that the UASB system is best suitable for implementation in the aerobic plants that have to be extended in capacity.

Treatment of raw sewage in a temperate climate using a UASB reactor and the hanging sponge cubes process

1997 ◽  
Vol 36 (6-7) ◽  
pp. 433-440 ◽  
Author(s):  
Lalit K. Agrawal ◽  
Yasuhiro Ohashi ◽  
Etsuo Mochida ◽  
Hiroyuki Okui ◽  
Yasuko Ueki ◽  
...  
Keyword(s):  
Ammonia Oxidation ◽  
Upflow Anaerobic Sludge Blanket ◽  
Uasb Reactor ◽  
Temperate Climate ◽  
Anaerobic Sludge ◽  
Treatment Efficiency ◽  
Oxidation Rates ◽  
Air Intake ◽  
Anaerobic Sludge Blanket ◽  
Digested Sewage Sludge

The treatability of raw sewage in a temperate climate (wintertime around 10–20°C) using an upflow anaerobic sludge blanket (UASB) reactor and the hanging sponge cubes process was evaluated. After being seeded with digested sewage sludge, a 47.1 L UASB reactor was continuously operated for more than 2 years by feeding raw sewage, which had average COD around 300 mg/L (41% soluble). During summertime at an HRT of 7 h, effluent COD approximately 70 mg/L total, 50 mg/L soluble and BOD5 20 mg/L total, 12 mg/L soluble was obtained. During wintertime also, treatment efficiency and process stability was good. With the hanging sponge cubes process using the effluent of the UASB reactor treating raw sewage, the following results were obtained. The ammonia oxidation rates of 1.9 and 3.5 g NH4-N·m−2·d−1 in a downflow hanging sponge cubes biofilter, under natural air intake only were obtained during wintertime and summertime, respectively. With post-denitrification and an external carbon source, 84% in average N (NO3+NO2) was removed with an HRT of less than 1 hour and in the temperature range of 13 to 30°C using an upflow submerged hanging sponge bed bioreactor, under anaerobic conditions. The overall system using a UASB reactor and the hanging sponge cubes process could be quite an attractive treatment alternative.

Toxicity and treatability of leachate: application of UASB reactor for leachate treatment from Okhla landfill, New Delhi

2012 ◽  
Vol 65 (10) ◽  
pp. 1887-1894 ◽  
Author(s):  
V. Singh ◽  
A. K. Mittal
Keyword(s):  
Oxygen Demand ◽  
Upflow Anaerobic Sludge Blanket ◽  
Uasb Reactor ◽  
Organic Loading Rate ◽  
Anaerobic Sludge ◽  
New Delhi ◽  
Leachate Treatment ◽  
Feed Composition ◽  
Laboratory Scale Reactor ◽  
Anaerobic Sludge Blanket

This study reports applicability of upflow anaerobic sludge blanket (UASB) process to treat the leachate from a municipal landfill located in Delhi. A laboratory scale reactor was operated at an organic loading rate of 3.00 kg chemical oxygen demand (COD)/m3 d corresponding to a hydraulic retention time (HRT) of 12 h for over 8 months. The effect of toxicity of leachate, and feed composition on the treatability of leachate was evaluated. Average COD of the leachate, during the study period varied between 8,880 and 66,420 mg/l. Toxicity of the leachate used during a period of 8 months varied from LC50 1.22 to 12.35 for 96 h. The removal efficiency of soluble COD ranged between 91 and 67% for fresh leachate and decreased drastically from 90 to 35% for old leachate having high toxicity. The efficiency varied from 81 to 65%. The reactor performed more efficiently for the treatment of fresh leachate (less toxic, LC50 11.64, 12.35, and 12.15 for 96 h) as compared with old leachate (more toxic, LC50 1.22 for 96 h). Toxicity of the leachate affected its treatment potential by the UASB.

scholarly journals A VFA-based controller for anaerobic digestion of industrial winery wastewater

2018 ◽  
Vol 78 (9) ◽  
pp. 1871-1878 ◽  
Author(s):  
Gustavo Vargas-Morales ◽  
Rolando Chamy ◽  
Santiago García-Gen
Keyword(s):  
Anaerobic Digestion ◽  
Volatile Fatty Acids ◽  
Upflow Anaerobic Sludge Blanket ◽  
Uasb Reactor ◽  
Organic Loading Rate ◽  
Anaerobic Sludge ◽  
Variable Gain ◽  
Winery Wastewater ◽  
Empirical Function ◽  
Anaerobic Sludge Blanket

Abstract A variable-gain controller for anaerobic digestion of industrial winery wastewater is presented. A control law using both volatile fatty acids (VFA) and methane production rate as controlled variables and organic loading rate (OLR) as manipulated variable is defined. The process state is quantitatively estimated by an empirical function comparing VFA measurements against a setpoint value; then, it is modified with a second empirical function that compares the methane flow rate with a maximum capacity reference, and finally it is adjusted with a third factor considering the actual hydraulic retention time. The variable-gain function determines the extent of the OLR change applied to the system. The controller was successfully validated in a 95 L upflow-anaerobic-sludge-blanket (UASB) reactor, treating industrial wine wastewater at OLR ranged between 2.0 and 39.2 g COD/L d for 120 days at mesophilic conditions. Higher performance was achieved contrasted with a conventional strategy carried out in a parallel UASB unit.

scholarly journals Black water treatment by an upflow anaerobic sludge blanket (UASB) reactor: a pilot study

2019 ◽  
Vol 80 (8) ◽  
pp. 1505-1511 ◽  
Author(s):  
Nathalie Dyane Miranda Slompo ◽  
Larissa Quartaroli ◽  
Grietje Zeeman ◽  
Gustavo Henrique Ribeiro da Silva ◽  
Luiz Antonio Daniel
Keyword(s):  
Removal Efficiency ◽  
Phase 1 ◽  
Oxygen Demand ◽  
Upflow Anaerobic Sludge Blanket ◽  
Uasb Reactor ◽  
Organic Loading Rate ◽  
Anaerobic Sludge ◽  
Phase 3 ◽  
Black Water ◽  
Anaerobic Sludge Blanket

Abstract Decentralized sanitary wastewater treatment has become a viable and sustainable alternative, especially for developing countries and small communities. Besides, effluents may present variations in chemical oxygen demand (COD), biochemical oxygen demand (BOD) and total nitrogen values. This study describes the feasibility of using a pilot upflow anaerobic sludge blanket (UASB) reactor to treat wastewater with different organic loads (COD), using black water (BW) and sanitary wastewater, in addition to its potential for preserving nutrients for later recovery and/or reuse. The UASB reactor was operated continuously for 95 weeks, with a hydraulic retention time of 3 days. In Phase 1, the reactor treated simulated BW and achieved 77% CODtotal removal. In Phase 2, treating only sanitary wastewater, the CODtotal removal efficiency was 60%. Phase 3 treated simulated BW again, and CODtotal removal efficiency was somewhat higher than in Phase 1, reaching 81%. In Phase 3, the removal of pathogens was also evaluated: the efficiency was 1.96 log for Escherichia coli and 2.13 log for total coliforms. The UASB reactor was able to withstand large variations in the organic loading rate (0.09–1.49 kg COD m−3 d−1), in continuous operation mode, maintaining a stable organic matter removal.

Anaerobic treatment of Wastewater from a fish-canning factory in a full-scale Upflow Anaerobic Sludge Blanket (UASB) reactor

1999 ◽  
Vol 40 (8) ◽  
pp. 57-62 ◽  
Author(s):  
A. Pun˜al ◽  
J. M. Lema
Keyword(s):  
Anaerobic Treatment ◽  
Upflow Anaerobic Sludge Blanket ◽  
Total Alkalinity ◽  
Uasb Reactor ◽  
Organic Loading Rate ◽  
Anaerobic Sludge ◽  
Stable Operation ◽  
Start Up ◽  
Upward Velocity ◽  
Anaerobic Sludge Blanket

The start-up and optimisation of a 380 m3 UASB reactor (Up-flow Anaerobic Sludge Blanket) treating wastewater from a fish-canning factory was carried out. At the beginning of the operation the Organic Loading Rate (OLR) was 1 kg COD/m3·d. Then, the load was gradually increased in steps of 50% OLR until the final capacity of the system (4 kg COD/m3·d) was achieved. Wastewater characteristics were highly dependent on the canned product (mussel, tuna, sardines, etc.). In spite of that, a stable operation working at a hydraulic retention time (HRT) of 2 days was maintained. Total Alkalinity (TA) always presented values higher than 3 g CaCO3/l, while the IA/TA ratio (Intermediate Alalinity/Total Alkalinity) was always maintained lower than 0.3. In order to improve granulation conditions, upward velocities from 0.5 to 0.8 m/h were applied. The highest values caused the washout of non-granulated biomass from the reactor, optimum operation being achieved at an upward velocity of 0.7 m/h.

scholarly journals Review of Upflow Anaerobic Sludge Blanket Reactor Technology: Effect of Different Parameters and Developments for Domestic Wastewater Treatment

2018 ◽  
Vol 2018 ◽  
pp. 1-13 ◽  
Author(s):  
M. K. Daud ◽  
Hina Rizvi ◽  
Muhammad Farhan Akram ◽  
Shafaqat Ali ◽  
Muhammad Rizwan ◽  
...  
Keyword(s):  
Wastewater Treatment ◽  
Green Energy ◽  
Upflow Anaerobic Sludge Blanket ◽  
Uasb Reactor ◽  
Organic Loading Rate ◽  
Anaerobic Sludge ◽  
Main Process ◽  
Treatment Technology ◽  
Effective Discharge ◽  
Anaerobic Sludge Blanket

The upflow anaerobic sludge blanket (UASB) reactor has been recognized as an important wastewater treatment technology among anaerobic treatment methods. The objective of this study was to perform literature review on the treatment of domestic sewage using the UASB reactor as the core component and identifying future areas of research. The merits of anaerobic and aerobic bioreactors are highlighted and other sewage treatment technologies are compared with UASB on the basis of performance, resource recovery potential, and cost. The comparison supports UASB as a suitable option on the basis of performance, green energy generation, minimal space requirement, and low capital, operation, and maintenance costs. The main process parameters such as temperature, hydraulic retention time (HRT), organic loading rate (OLR), pH, granulation, and mixing and their effects on the performance of UASB reactor and hydrogen production are presented for achieving optimal results. Feasible posttreatment steps are also identified for effective discharge and/or reuse of treated water.

Comparison of start-up of an upflow anaerobic sludge blanket reactor and a polyurethane carrier reactor

1996 ◽  
Vol 34 (5-6) ◽  
pp. 509-515 ◽  
Author(s):  
Huub J. Gijzen ◽  
Frank Kansiime
Keyword(s):  
Volatile Fatty Acids ◽  
Biogas Production ◽  
Upflow Anaerobic Sludge Blanket ◽  
Uasb Reactor ◽  
Organic Loading Rate ◽  
Anaerobic Sludge ◽  
Operational Conditions ◽  
Start Up ◽  
And Performance ◽  
Anaerobic Sludge Blanket

The start-up and performance of an Upflow Anaerobic Sludge Blanket (UASB) reactor and a Polyurethane Carrier Reactor (PCR) was investigated under similar operational conditions. The presence of polyurethane cubes as a carrier material in the PCR resulted in fast reactor start-up due to quick immobilization of methanogenic associations. Start-up of the UASB was slower compared to the PCR, which was mainly reflected in a lower biogas production and acetate degradation efficiency. However, when enough biomass had accumulated in the UASB reactor after 15 weeks of operation, the performance of the two reactors was almost the same in terms of biogas production and volatile fatty acids degradation. Efficient VFA degradation (about 90%) and biogas production (5.2 l/l.d) were achieved at an organic loading rate of 13.2 g/l.d) and HRT of 6 h. When hydraulic retention time was subsequently reduced from 6 to 2 h, the performance of the UASB reactor was better than that of the PCR. The inferior performance of the PCR may have been attributed to channelling of the influent in the reactor at high liquid flow rate.

Performance of plastic- and sponge-based trickling filters treating effluents from an UASB reactor

2013 ◽  
Vol 67 (5) ◽  
pp. 1034-1042 ◽  
Author(s):  
P. G. S. Almeida ◽  
A. K. Marcus ◽  
B. E. Rittmann ◽  
C. A. L. Chernicharo
Keyword(s):  
Organic Matter ◽  
Oxygen Demand ◽  
Upflow Anaerobic Sludge Blanket ◽  
Uasb Reactor ◽  
Organic Loading Rate ◽  
Anaerobic Sludge ◽  
Total N ◽  
Trickling Filters ◽  
N Removal ◽  
Anaerobic Sludge Blanket

The paper compares the performance of two trickling filters (TFs) filled with plastic- or sponge-based packing media treating the effluent from an upflow anaerobic sludge blanket (UASB) reactor. The UASB reactor was operated with an organic loading rate (OLR) of 1.2 kgCOD m−3 d−1, and the OLR applied to the TFs was 0.30–0.65 kgCOD m−3 d−1 (COD: chemical oxygen demand). The sponge-based packing medium (Rotosponge) gave substantially better performance for ammonia, total-N, and organic matter removal. The superior TF-Rotosponge performance for NH4+-N removal (80–95%) can be attributed to its longer biomass and hydraulic retention times (SRT and HRT), as well as enhancements in oxygen mass transfer by dispersion and advection inside the sponges. Nitrogen removals were significant (15 mgN L−1) in TF-Rotosponge when the OLRs were close to 0.75 kgCOD m−3 d−1, due to denitrification that was related to solids hydrolysis in the sponge interstices. For biochemical oxygen demand removal, higher HRT and SRT were especially important because the UASB removed most of the readily biodegradable organic matter. The new configuration of the sponge-based packing medium called Rotosponge can enhance the feasibility of scaling-up the UASB/TF treatment, including when retrofitting is necessary.

Sign in / Sign up

Export Citation Format

Share Document