Pilot-scale two-stage process: a combination of acidogenic hydrogenesis and methanogenesis

2005 ◽  
Vol 52 (1-2) ◽  
pp. 131-138 ◽  
Author(s):  
S.-K. Han ◽  
S.-H. Kim ◽  
H.-W. Kim ◽  
H.-S. Shin
Keyword(s):  
Food Waste ◽  
Environmental Conditions ◽  
Loading Rate ◽  
Pilot Scale ◽  
Uasb Reactor ◽  
Maximum Efficiency ◽  
Two Stage ◽  
Loading Rates ◽  
High Loading Rate ◽  
Stage Process

This study was performed to optimize both acidogenic hydrogenesis and methanogenesis, and then to develop a pilot-scale two-stage process producing not only CH4 but also H2. Firstly, acidogenic hydrogenesis of food waste was examined in pilot-scale leaching-bed reactors using dilution rate (D) as a tool to improve the environmental conditions. The maximum efficiency of 71.4% was obtained by adjusting D from 4.5 to 2.5 d−1 depending on the state of degradation. Secondly, the wastewater from acidogenic hydrogenesis was converted to CH4 in a pilot-scale UASB reactor. The COD removal efficiency exceeded 95% up to the loading rates of 13.1 g COD/L/d, which corresponded to HRT of 0.25 d (6 h). Lastly, a pilot-scale two-stage process was devised based on a combination of acidogenic hydrogenesis and methanogenesis. Over 120 days, the pilot-scale process resulted in large VS reduction of 70.9% at the high loading rate of 12.5 kg VS/m3/d in a short SRT of 8 days.

scholarly journals A Comparison of Two-Stage and Traditional Co-Composting of Green Waste and Food Waste Amended with Phosphate Rock and Sawdust

2021 ◽  
Vol 13 (3) ◽  
pp. 1109
Author(s):  
Edgar Ricardo Oviedo-Ocaña ◽  
Angélica María Hernández-Gómez ◽  
Marcos Ríos ◽  
Anauribeth Portela ◽  
Viviana Sánchez-Torres ◽  
...  
Keyword(s):  
Organic Matter ◽  
Product Quality ◽  
Food Waste ◽  
Phosphate Rock ◽  
Pilot Scale ◽  
Two Stage ◽  
Green Waste ◽  
Wet Weight ◽  
Two Phases

The composting of green waste (GW) proceeds slowly due to the presence of slowly degradable compounds in that substrate. The introduction of amendments and bulking materials can improve organic matter degradation and end-product quality. However, additional strategies such as two-stage composting, can deal with the slow degradation of green waste. This paper evaluates the effect of two-stage composting on the process and end-product quality of the co-composting of green waste and food waste amended with sawdust and phosphate rock. A pilot-scale study was developed using two treatments (in triplicate each), one being a two-stage composting and the other being a traditional composting. The two treatments used the same mixture (wet weight): 46% green waste, 19% unprocessed food waste, 18% processed food waste, 13% sawdust, and 4% phosphate rock. The traditional composting observed a higher degradation rate of organic matter during the mesophilic and thermophilic phases and observed thermophilic temperatures were maintained for longer periods during these two phases compared to two-stage composting (i.e., six days). Nonetheless, during the cooling and maturation phases, the two treatments had similar behaviors with regard to temperature, pH, and electrical conductivity, and the end-products resulting from both treatments did not statistically differ. Therefore, from this study, it is concluded that other additional complementary strategies must be evaluated to further improve GW composting.

Coarse filters for pond effluent polishing: comparison of loading rates and grain sizes

2007 ◽  
Vol 55 (11) ◽  
pp. 121-126 ◽  
Author(s):  
M. von Sperling ◽  
J.G.B. de Andrada ◽  
W.R. de Melo Júnior
Keyword(s):  
Loading Rate ◽  
Uasb Reactor ◽  
E Coli ◽  
Effluent Quality ◽  
Loading Rates ◽  
Hydraulic Loading ◽  
Grain Sizes ◽  
Belo Horizonte ◽  
The City ◽  
Rock Size

A system comprising a UASB reactor, shallow polishing ponds and shallow coarse filters, treating actual wastewater from the city of Belo Horizonte, Brazil, has been evaluated. The main focus of the research was to compare grain sizes and hydraulic loading rates in the coarse filters. Two filters operating in parallel were investigated, with the following grain sizes: Filter 1: 3 to 10 cm; Filter 2: 8 to 20 cm. Two hydraulic loading rates were tested: 0.5 and 1.0 m3/m3.d. The filter with the lower rock size had a better performance than the filter with the larger rock size in the removal of SS and, as a consequence, BOD and COD. A better performance was obtained with the hydraulic loading rate of 0.5 m3/m3.d, as compared to the rate of 1.0 m3/m3.d. The effluent quality during the period with the lower loading rate was very good for discharge into water bodies or for agricultural reuse (median effluent concentrations from Filter 1: BOD: 20 mg/L; COD: 106 mg/L; SS: 28 mg/L; E. coli: 528 MPN/100 mL).

scholarly journals The Concept of Wastes to Energy Using Sugary Wastes

2012 ◽  
Vol 9 ◽  
pp. 57-62
Author(s):  
Fiza Sarwar ◽  
Wajeeha Malik ◽  
Muhammad Salman Ahmed ◽  
Harja Shahid
Keyword(s):  
Volatile Fatty Acids ◽  
Loading Rate ◽  
Biogas Production ◽  
Oxygen Demand ◽  
Uasb Reactor ◽  
Organic Loading Rate ◽  
Anaerobic Sludge ◽  
Loading Rates ◽  
Sugar Mills ◽  
Anaerobic Sludge Blanket

Abstract: This study was designed using actual effluent from the sugary mills in an Up-flow Anaerobic Sludge Blanket (UASB) Reactor to evaluate treatability performance. The reactor was started-up in step-wise loading rates beginning from 0.05kg carbon oxygen demand (COD)/m3-day to 3.50kg-COD/m3-day. The hydraulic retention time (HRT) was slowly decreased from 96 hrs to eight hrs. It was observed that the removal efficiency of COD of more than 73% can be easily achieved at an HRT of more than 16 hours corresponding to an average organic loading rate (OLR) of 3.0kg-COD/m3-day, at neutral pH and constant temperature of 29°C. The average VFAs (volatile fatty acids) and biogas production was observed as 560mg/L and 1.6L/g-CODrem-d, respectively. The average methane composition was estimated as 62%. The results of this study suggest that the treatment of sugar mills effluent with the anaerobic technology seems to be more reliable, effective and economical.DOI: http://dx.doi.org/10.3126/hn.v9i0.7075 Hydro Nepal Vol.9 July 2011 57-62

Anaerobic treatment for C and S removal in “zero-discharge” paper mills: effects of process design on S removal efficiencies

2001 ◽  
Vol 44 (4) ◽  
pp. 189-195 ◽  
Author(s):  
J. B. van Lier ◽  
P. N.L. Lens ◽  
L. W. Hulshoff Pol
Keyword(s):  
Loading Rate ◽  
Anaerobic Treatment ◽  
Process Water ◽  
Uasb Reactor ◽  
Organic Loading ◽  
Production Rates ◽  
Paper Mills ◽  
Loading Rates ◽  
Zero Discharge ◽  
Uasb Reactors

Stringent environmental laws in Europe and Northern America lead to the development towards closure of the process water streams in pulp and paper mills. Application of a "zero-discharge" process is already a feasible option for the board and packaging paper industry, provided in-line treatment is applied. Concomitant energy conservation inside the mill results in process water temperatures of 50-60°C. Thermophilic anaerobic treatment complemented with appropriate post-treatment is considered as the most cost-effective solution to meet re-use criteria of the process water and to keep its temperature. In the proposed closed-cycle, the anaerobic treatment step removes the largest fraction of the biodegradable COD and eliminates “S” as H2S from the process stream, without the use of additional chemicals. The anaerobic step is regarded as the only possible location to bleed "S" from the process water cycle. In laboratory experiments, the effect of upward liquid velocity (Vupw) and the specific gas loading rate (Vgas) on the S removal capacity of thermophilic anaerobic bio-reactors was investigated. Acidifying, sulphate reducing sludge bed reactors were fed with partly acidified synthetic paper mill wastewater and were operated at 55°C and pH 6. The reactors were operated at organic loading rates up to 50 g COD.l−1.day−1 at COD/SO42- ratios of 10. The effect of Vupw was researched by comparing the performance of a UASB reactor operated at 1.0 m.h−1 and an EGSB reactor, operated at 6.8 m.h−1. The Vupw had a strong effect on the fermentation patterns. In the UASB reactor, acidification yielded H2, acetate and propionate, leading to an accumulation of reducing equivalents. These were partly disposed of by the production of n-butyrate and n-valerate from propionate. In the EGSB reactor net acetate consumption was observed as well as high volumetric gas (CO2 and CH4) production rates. The higher gas production rates in the EGSB reactor resulted in higher S-stripping efficiencies. The effect of Vgas was further researched by comparing 2 UASB reactors which were sparged with N2 gas at a specific gas loading rate of 30 m3.m−2.day−1. In contrast to the regular UASB reactors, the gas-supplied UASB showed a more stable performance when the organic loading rates were increased. Also, the H2S stripping efficiency was 3-4 times higher in the gas-supplied UASB, reaching values of 67%. Higher values were not obtained owing to the relatively poor sulphate reduction efficiencies.

Anaerobic treatment of a medium strength industrial wastewater at low-temperature and short hydraulic retention time: a pilot-scale experience

2011 ◽  
Vol 64 (8) ◽  
pp. 1629-1635 ◽  
Author(s):  
M. Esparza Soto ◽  
C. Solís Morelos ◽  
J. J. Hernández Torres
Keyword(s):  
Low Temperature ◽  
Hydraulic Retention Time ◽  
Loading Rate ◽  
Pilot Scale ◽  
Anaerobic Treatment ◽  
Uasb Reactor ◽  
Organic Loading Rate ◽  
Organic Loading ◽  
Processing Industry ◽  
Industry Wastewater

The aim of this work was to evaluate the performance of a pilot-scale upflow anaerobic sludge blanket (UASB) reactor during the treatment of cereal-processing industry wastewater under low-temperature conditions (17 °C) for more than 300 days. The applied organic loading rate (OLRappl) was gradually increased from 4 to 6 and 8 kg CODsol/m3d by increasing the influent soluble chemical oxygen demand (CODsol), while keeping the hydraulic retention time constant (5.2 h). The removal efficiency was high (82 to 92%) and slightly decreased after increasing the influent CODsol and the OLRappl. The highest removed organic loading rate (OLRrem) was reached when the UASB reactor was operated at 8 kg CODsol/m3d and it was two times higher than that obtained for an OLRappl of 4 kg CODsol/m3d. Some disturbances were observed during the experimentation. The formation of biogas pockets in the sludge bed significantly complicated the biogas production quantification, but did not affect the reactor performance. The volatile fatty acids in the effluent were low, but increased as the OLRappl increased, which caused an increment of the effluent CODsol. Anaerobic treatment at low temperature was a good option for the biological pre-treatment of cereal processing industry wastewater.

Assessment of increasing loading rate on two-stage digestion of food waste

2016 ◽  
Vol 202 ◽  
pp. 172-180 ◽  
Author(s):  
M.A. Voelklein ◽  
A. Jacob ◽  
R. O’ Shea ◽  
J.D. Murphy
Keyword(s):  
Food Waste ◽  
Loading Rate ◽  
Two Stage

Characterization of microbial community in the two-stage process for hydrogen and methane production from food waste

2010 ◽  
Vol 35 (15) ◽  
pp. 8253-8261 ◽  
Author(s):  
Chun-Feng Chu ◽  
Yoshitaka Ebie ◽  
Kai-Qin Xu ◽  
Yu-You Li ◽  
Yuhei Inamori
Keyword(s):  
Microbial Community ◽  
Food Waste ◽  
Methane Production ◽  
Two Stage ◽  
Stage Process

Continuous hydrogen and methane production in a two-stage cheese whey fermentation system

2011 ◽  
Vol 64 (2) ◽  
pp. 367-374 ◽  
Author(s):  
C. B. Cota-Navarro ◽  
J. Carrillo-Reyes ◽  
G. Davila-Vazquez ◽  
F. Alatriste-Mondragón ◽  
E. Razo-Flores
Keyword(s):  
Methane Production ◽  
Cheese Whey ◽  
Continuous Production ◽  
Uasb Reactor ◽  
Organic Loading Rate ◽  
Stable Operation ◽  
Operational Parameters ◽  
Two Stage ◽  
Production Of Hydrogen ◽  
Stage Process

The feasibility of integrating biological hydrogen and methane production in a two-stage process using mixed cultures and cheese whey powder (CWP) as substrate was studied. The effect of operational parameters such as hydraulic retention time (HRT) and organic loading rate (OLR) on the volumetric hydrogen (VHPR) and methane (VMPR) production rates was assessed. The highest VHPR was 28 L H2/L/d, obtained during stable operation in a CSTR at HRT and OLR of 6 h and 142 g lactose/L/d, respectively. Moreover, hydrogen (13 L/L/d) was produced even at HRT as low as 3.5 h and OLR of 163 g lactose/L/d, nonetheless, the reactor operation was not stable. Regarding methane production in an UASB reactor, the acidified effluent from the hydrogen-producing bioreactor was efficiently treated obtaining COD removals above 90% at OLR and HRT of 20 g COD/L/d and 6 h, respectively. The two-stage process for continuous production of hydrogen and methane recovered over 70% of the energy present in the substrate. This study demonstrated that hydrogen production can be efficiently coupled to methane production in a two-stage system and that CWP is an adequate substrate for energy production.

Sign in / Sign up

Export Citation Format

Share Document