Treatability of cefazolin antibiotic formulation effluent with O3 and O3/H2O2 processes

2007 ◽  
Vol 55 (10) ◽  
pp. 217-225 ◽  
Author(s):  
G. Iskender ◽  
A. Sezer ◽  
I. Arslan-Alaton ◽  
F. Germirli Babuna ◽  
O.S. Okay
Keyword(s):  
Acute Toxicity ◽  
Activated Sludge ◽  
Removal Efficiency ◽  
Inhibition Test ◽  
Cod Removal ◽  
Cod Removal Efficiency

The effect of applying ozonation and perozonation to antibiotic cefazolin-Na formulation effluents were investigated in this study. Twenty minutes of ozonation at a rate of 1,500 mg/L-h was observed to remove COD by 38%, whereas a COD removal efficiency of 40% was achieved via H2O2 enhanced ozonation (same conditions + 31.25 mM H2O2). Both of the pretreatment alternatives were monitored to elevate the BOD5/COD ratio from 0.01 to 0.08. The initially inert COD was reduced by 38% using ozonation and by 60% employing H2O2 enhanced ozonation. In terms of the lowest achievable effluent COD levels after bio-treatment, ozonation was observed to yield a residual COD of 205 mg L−1, while a residual COD of 135 mg L−1 was involved for perozonation. According to the results of acute toxicity on Phaedactylum tricornutum, ozonated and perozonated samples exhibited more toxicity than the untreated effluent after 4 days. The activated sludge inhibition test demonstrated that both of the pretreatment alternatives efficiently eliminated the inhibition of investigated formulation effluent.

scholarly journals Investigation of Heavy Metal Effects on the Anaerobic Co-Digestion Process of Waste Activated Sludge and Septic Tank Sludge

2019 ◽  
Vol 2019 ◽  
pp. 1-9
Author(s):  
Quang-Minh Nguyen ◽  
Duy-Cam Bui ◽  
Thao Phuong ◽  
Van-Huong Doan ◽  
Thi-Nham Nguyen ◽  
...  
Keyword(s):  
Heavy Metals ◽  
Heavy Metal ◽  
Activated Sludge ◽  
Removal Efficiency ◽  
Biogas Production ◽  
Cod Removal ◽  
Septic Tank ◽  
Waste Activated Sludge ◽  
Digestion Process ◽  
Cod Removal Efficiency

The effect of copper, zinc, chromium, and lead on the anaerobic co-digestion of waste activated sludge and septic tank sludge in Hanoi was studied in the fermentation tests by investigating the substrate degradation, biogas production, and process stability at the mesophilic fermentation. The tested heavy metals were in a range of concentrations between 19 and 80 ppm. After the anaerobic tests, the TS, VS, and COD removal efficiency was 4.12%, 9.01%, and 23.78% for the Cu(II) added sample. Similarly, the efficiencies of the Zn(II) sample were 1.71%, 13.87%, and 16.1% and Cr(VI) efficiencies were 15.28%, 6.6%, and 18.65%, while the TS, VS, and COD removal efficiency of the Pb(II) added sample was recorded at 16.1%, 17.66%, and 16.03% at the concentration of 80 ppm, respectively. Therefore, the biogas yield also decreased by 36.33%, 31.64%, 31.64%, and 30.60% for Cu(II), Zn(II), Cr(VI), and Pb(II) at the concentration of 80 ppm, compared to the raw sample, respectively. These results indicated that Cu(II) had more inhibiting effect on the anaerobic digestion of the sludge mixture than Zn(II), Cr(VI), and Pb(II). The relative toxicity of these heavy metals to the co-digestion process was as follows: Cu (the most toxic) > Zn > Cr > Pb (the least toxic). The anaerobic co-digestion process was inhibited at high heavy metal concentration, which resulted in decreased removal of organic substances and produced biogas.

scholarly journals Bioaugmentation as a Tool To Protect the Structure and Function of an Activated-Sludge Microbial Community against a 3-Chloroaniline Shock Load

2003 ◽  
Vol 69 (3) ◽  
pp. 1511-1520 ◽  
Author(s):  
Nico Boon ◽  
Eva M. Top ◽  
Willy Verstraete ◽  
Steven D. Siciliano
Keyword(s):  
Microbial Community ◽  
Activated Sludge ◽  
Real Time ◽  
Removal Efficiency ◽  
Real Time Pcr ◽  
Denaturing Gradient Gel Electrophoresis ◽  
Cod Removal ◽  
Shock Load ◽  
Volume Index ◽  
Cod Removal Efficiency

ABSTRACT Bioaugmentation of bioreactors focuses on the removal of xenobiotics, with little attention typically paid to the recovery of disrupted reactor functions such as ammonium-nitrogen removal. Chloroanilines are widely used in industry as a precursor to a variety of products and are occasionally released into wastewater streams. This work evaluated the effects on activated-sludge reactor functions of a 3-chloroaniline (3-CA) pulse and bioaugmentation by inoculation with the 3-CA-degrading strain Comamonas testosteroni I2 gfp. Changes in functions such as nitrification, carbon removal, and sludge compaction were studied in relation to the sludge community structure, in particular the nitrifying populations. Denaturing gradient gel electrophoresis (DGGE), real-time PCR, and fluorescent in situ hybridization (FISH) were used to characterize and enumerate the ammonia-oxidizing microbial community immediately after a 3-CA shock load. Two days after the 3-CA shock, ammonium accumulated, and the nitrification activity did not recover over a 12-day period in the nonbioaugmented reactors. In contrast, nitrification in the bioaugmented reactor started to recover on day 4. The DGGE patterns and the FISH and real-time PCR data showed that the ammonia-oxidizing microbial community of the bioaugmented reactor recovered in structure, activity, and abundance, while the number of ribosomes of the ammonia oxidizers in the nonbioaugmented reactor decreased drastically and the community composition changed and did not recover. The settleability of the activated sludge was negatively influenced by the 3-CA addition, with the sludge volume index increasing by a factor of 2.3. Two days after the 3-CA shock in the nonbioaugmented reactor, chemical oxygen demand (COD) removal efficiency decreased by 36% but recovered fully by day 4. In contrast, in the bioaugmented reactor, no decrease of the COD removal efficiency was observed. This study demonstrates that bioaugmentation of wastewater reactors to accelerate the degradation of toxic chlorinated organics such as 3-CA protected the nitrifying bacterial community, thereby allowing faster recovery from toxic shocks.

Performance evaluation of various aerobic biological systems for the treatment of domestic wastewater at low temperatures

2008 ◽  
Vol 58 (4) ◽  
pp. 819-830 ◽  
Author(s):  
N. Sundaresan ◽  
L. Philip
Keyword(s):  
Performance Evaluation ◽  
Activated Sludge ◽  
Fluidized Bed ◽  
Removal Efficiency ◽  
Biological Systems ◽  
Domestic Wastewater ◽  
Cod Removal ◽  
Synthetic Wastewater ◽  
Activated Sludge Process ◽  
Cod Removal Efficiency

Studies were undertaken on the performance evaluation of three different types of aerobic reactors, namely, activated sludge process, fluidized bed reactor and submerged bed reactor. Initially synthetic wastewater was used for stabilizing the system and later domestic wastewater of IIT Madras was used as the feed for the biological systems. The hydraulic retention time was maintained as 24 h. The seed sludge was collected from IIT Madras sewage treatment plant. The inlet COD to the reactors with synthetic wastewater was 1,000±20 mg/L and with real wastewater, it was 150 to 350 mg/L. The performance of the reactors was evaluated based on the soluble COD and nitrogen removal efficiency. The pH, temperature, dissolved oxygen (DO) and mixed liquid suspended solid (MLSS) concentration were measured periodically. The reactors were acclimatized at 35°C in batch mode and changed to continuous mode at 30°C. After the systems attained its steady state at a particular temperature, the temperature was reduced from 35°C to 5°C stepwise, with each step of 5°C. The start-up time for submerged bed reactor was slightly more than fluidized and conventional activated sludge process. The COD removal efficiency of the three reactors was higher with synthetic wastewaters as compared to actual domestic wastewater. Submerged bed reactor was more robust and efficient as compared to activated sludge and fluidized bed reactors. The COD removal efficiency of the reactors was relatively good until the operating temperature was maintained at 15°C or above. At 10°C, submerged bed reactor was able to achieve 40% COD removal efficiency whereas; the fluidized bed and conventional ASP reactors were showing only 20% COD removal efficiency. At 5°C, almost all the systems failed. Submerged bed reactor showed around 20% COD removal efficiency. However, this reactor was able to regain its 90% of original efficiency, once the temperature was raised to 10°C. At higher temperatures, the nitrification efficiency of the reactors was above 80–90%. As the temperature reduced the nitrification efficiency has reduced drastically. In summary, submerged bed reactors seems to be a better option for treating domestic wastewaters at low temperature regions.

Effects of Molybdenum (VI) on the Denitrification Performance of Activated Sludge Process

2011 ◽  
Vol 183-185 ◽  
pp. 1400-1403
Author(s):  
Xue Zheng Meng ◽  
Xiang Sheng Cao ◽  
Jie Rui Li
Keyword(s):  
Activated Sludge ◽  
Removal Efficiency ◽  
Removal Rate ◽  
Nitrate Removal ◽  
Cod Removal ◽  
Activated Sludge Process ◽  
Inhibitory Effects ◽  
Batch Tests ◽  
Cod Removal Efficiency

The effects of molybdenum (Ⅵ) on the denitrification efficiency of activated sludge process were investigated with batch tests. The results indicated that up to 5 mg/L of Molybdenum (Ⅵ) concentrations in the liquor of activated sludge process could accelerate the nitrate removal rate, exhibiting maximum stimulation at 1 mg/L. Up to 4 mg/L of Molybdenum (Ⅵ) concentrations, the COD removal efficiency was enhanced. Up to 1mg/L of Molybdenum (Ⅵ) concentrations, the TTC-DHA was enhanced but higher concentration showed inhibitory effects. Based on the integrated effects of Molybdenum (Ⅵ) on nitrate and COD removal with the TTC-DHA change, 1mg/L of Molybdenum (Ⅵ) is proposed as the best concentration for denitrification of activated sludge.

scholarly journals Combined treatment of hydroxypropyl guar gum in oilfield fracturing wastewater by coagulation and the UV/H2O2/ferrioxalate complexes process

2017 ◽  
Vol 77 (3) ◽  
pp. 565-575 ◽  
Author(s):  
Zhenchao Zhang
Keyword(s):  
Removal Efficiency ◽  
Guar Gum ◽  
Combined Treatment ◽  
Cod Removal ◽  
Treated Wastewater ◽  
Spectra Analysis ◽  
Hydroxypropyl Guar ◽  
Coagulation Process ◽  
Cod Removal Efficiency ◽  
Hydroxypropyl Guar Gum

Abstract Hydroxypropyl guar gum is considered to be a main component of oilfield fracturing wastewater (OFW). This work is intended to optimize the experimental conditions for the maximum oxidative degradation of hydroxypropyl guar gum by the coagulation and UV/H2O2/ferrioxalate complexes process. Optimal reaction conditions were proposed based on the chemical oxygen demand (COD) removal efficiency and UV_vis spectra analysis. The overall removal efficiency of COD reached 83.8% for a dilution ratio of raw wastewater of 1:2, pH of 4 and FeCl3 loading of 1,000 mg/L in the coagulation process; the dosage of H2O2 (30%,v/v) was 0.6% (v/v) and added in three steps, the n(H2O2)/n(Fe2+) was 2:1, n(Fe2+)/n(C2O42−) was 3:1 and pH was 4 in the UV/H2O2/ferrioxalate complexes process; pH was adjusted to 8.5–9 by NaOH and then cationic polyacrylamide (CPAM) of 2 mg/L was added in the neutralization and flocculation process. The decrease in COD during the coagulation process reduced the required H2O2 dosage and improved efficiency in the subsequent UV/H2O2/ferrioxalate complexes process. Furthermore, COD removal efficiency significantly increased by more than 13.4% with the introduction of oxalate compared with UV/Fenton. The UV_vis spectra analysis results indicated that the coagulation and UV/H2O2/ferrioxalate complexes process could efficiently remove the hydroxypropyl guar gum dissolved in OFW. An optimal combination of these parameters produced treated wastewater that met the GB8978-1996 Integrated Wastewater Discharge Standard level III emission standard.

Textile Wastewater Treatment Using Combined Process of Biological Wriggle Bed and Ozone Biological Aerated Filter

2012 ◽  
Vol 441 ◽  
pp. 589-592
Author(s):  
Zhi Min Fu ◽  
Yu Gao Zhang ◽  
Xiao Jun Wang
Keyword(s):  
Wastewater Treatment ◽  
Removal Efficiency ◽  
Textile Wastewater ◽  
Cod Removal ◽  
Biological Aerated Filter ◽  
Combined Process ◽  
Cod Removal Efficiency ◽  
Aerated Filter ◽  
Textile Wastewater Treatment

A combined process of biological wriggle bed and ozone biological aerated filter was utilized to treat textile wastewater. Results showed that COD removal efficiency was almost 90.4%. The average effluent COD was 85.87 mg/L. The effluent colority was 64-32 times. This study indicated that the combined process is potentially useful for treating textile wastewater.

Electrocoagulation and nanofiltration integrated process application in purification of bilge water using response surface methodology

2016 ◽  
Vol 74 (3) ◽  
pp. 564-579 ◽  
Author(s):  
Ceyhun Akarsu ◽  
Yasin Ozay ◽  
Nadir Dizge ◽  
H. Elif Gulsen ◽  
Hasan Ates ◽  
...  
Keyword(s):  
Response Surface Methodology ◽  
Response Surface ◽  
Removal Efficiency ◽  
Cod Removal ◽  
Positive Sign ◽  
Aluminum Electrode ◽  
Integrated Process ◽  
Bilge Water ◽  
Cod Removal Efficiency ◽  
Initial Ph

Marine pollution has been considered an increasing problem because of the increase in sea transportation day by day. Therefore, a large volume of bilge water which contains petroleum, oil and hydrocarbons in high concentrations is generated from all types of ships. In this study, treatment of bilge water by electrocoagulation/electroflotation and nanofiltration integrated process is investigated as a function of voltage, time, and initial pH with aluminum electrode as both anode and cathode. Moreover, a commercial NF270 flat-sheet membrane was also used for further purification. Box–Behnken design combined with response surface methodology was used to study the response pattern and determine the optimum conditions for maximum chemical oxygen demand (COD) removal and minimum metal ion contents of bilge water. Three independent variables, namely voltage (5–15 V), initial pH (4.5–8.0) and time (30–90 min) were transformed to coded values. The COD removal percent, UV absorbance at 254 nm, pH value (after treatment), and concentration of metal ions (Ti, As, Cu, Cr, Zn, Sr, Mo) were obtained as responses. Analysis of variance results showed that all the models were significant except for Zn (P > 0.05), because the calculated F values for these models were less than the critical F value for the considered probability (P = 0.05). The obtained R2 and Radj2 values signified the correlation between the experimental data and predicted responses: except for the model of Zn concentration after treatment, the high R2 values showed the goodness of fit of the model. While the increase in the applied voltage showed negative effects, the increases in time and pH showed a positive effect on COD removal efficiency; also the most effective linear term was found as time. A positive sign of the interactive coefficients of the voltage–time and pH–time systems indicated synergistic effect on COD removal efficiency, whereas interaction between voltage and pH showed an antagonistic effect.

scholarly journals Impact of Precipitants on the Structure and Properties of Fe-Co-Ce Composite Catalysts

2016 ◽  
Vol 2016 ◽  
pp. 1-8
Author(s):  
Yongli Zhang ◽  
Shujuan Dai ◽  
Yanbo Zhou ◽  
Kai Lin
Keyword(s):  
Particle Size ◽  
Methyl Orange ◽  
Removal Efficiency ◽  
Cod Removal ◽  
Catalytic Wet Air Oxidation ◽  
Structure And Properties ◽  
Air Oxidation ◽  
Wet Air Oxidation ◽  
Composite Catalysts ◽  
Cod Removal Efficiency

Fe-Co-Ce composite catalysts were prepared by coprecipitation method using CO(NH2)2, NaOH, NH4HCO3, and NH3·H2O as precipitant agents. The effects of the precipitant agents on the physicochemical properties of the Fe-Co-Ce based catalysts were investigated by SEM, TEM, BET, TG-DTA, and XRD. It was found that the precipitant agents remarkably influenced the morphology and particle size of the catalysts and affected the COD removal efficiency, decolorization rate, and pH of methyl orange for catalytic wet air oxidation (CWAO). The specific surface area of the Fe-Co-Ce composite catalysts successively decreased in the order of NH3·H2O, NH4HCO3, NaOH, and CO(NH2)2, which correlated to an increasing particle size that increased for each catalyst. For the CWAO of a methyl orange aqueous solutions, the effects of precipitant agents NH3·H2O and NaOH were superior to those of CO(NH2)2and NH4HCO3. The catalyst prepared using NH3·H2O as the precipitant agent was mostly composed of Fe2O3, CoO, and CeO2. The COD removal efficiency of methyl orange aqueous solution for NH3·H2O reached 92.9% in the catalytic wet air oxidation. Such a catalytic property was maintained for six runs.

Development of a two-stage flexible fibre biofilm reactor for treatment of food processing wastewater

2003 ◽  
Vol 47 (11) ◽  
pp. 189-194 ◽  
Author(s):  
Q.J. Yu ◽  
H. Xu ◽  
D. Yao ◽  
P. Williams
Keyword(s):  
Removal Efficiency ◽  
Food Processing ◽  
Cost Effective ◽  
Biofilm Reactor ◽  
Cod Removal ◽  
Two Stage ◽  
Cod Removal Efficiency ◽  
Cost Effective Treatment ◽  
Removal Efficiencies ◽  
Food Processing Wastewater

Biofilm (or attached growth) reactors can be effectively used to treat organic wastewater from various industries such as food processing industry. They have a number of advantages including high organic loading rates (OLRs) and improved operational stability. A flexible fibre biofim reactor (FFBR) has been developed for efficient and cost effective treatment of food processing wastewater. In the process, simple flexible fibre packing with a very high specific surface area is used as support for microorganisms. The COD removal efficiencies for a range of OLRs have been studied. The FFBR can support an increasingly high OLR, but with a corresponding decrease in the COD removal efficiency. Therefore, a two-stage FFBR was developed to increase the treatment efficiency for systems with high OLRs. Experimental results indicated that a high overall COD removal efficiency could be achieved. At an influent COD of about 2700 mg/L and an OLR of 7.7 kgCOD/m3d, COD removal efficiencies of 76% and 82% were achieved in the first and the second stage of the reactor, respectively. The overall COD removal efficiency was 96%. Therefore, even for wastewater samples with high organic strength, high quality treated effluents could be readily achieved by the use of multiple stage FFBRs.

scholarly journals Treatment of oilfield wastewater by combined process of micro-electrolysis, Fenton oxidation and coagulation

2017 ◽  
Vol 76 (12) ◽  
pp. 3278-3288 ◽  
Author(s):  
Zhenchao Zhang
Keyword(s):  
Reaction Time ◽  
Removal Efficiency ◽  
Treatment Process ◽  
Cod Removal ◽  
Fenton Oxidation ◽  
Oily Wastewater ◽  
Optimum Conditions ◽  
Combined Process ◽  
Cod Removal Efficiency ◽  
Optimized Conditions

Abstract In this study, a combined process was developed that included micro-electrolysis, Fenton oxidation and coagulation to treat oilfield fracturing wastewater. Micro-electrolysis and Fenton oxidation were applied to reduce chemical oxygen demand (COD) organic load and to enhance organic components gradability, respectively. Orthogonal experiment were employed to investigate the influence factors of micro-electrolysis and Fenton oxidation on COD removal efficiency. For micro-electrolysis, the optimum conditions were: pH, 3; iron-carbon dosage, 50 mg/L; mass ratio of iron-carbon, 2:3; reaction time, 60 min. For Fenton oxidation, a total reaction time of 90 min, a H2O2 dosage of 12 mg/L, with a H2O2/Fe2+ mole ratio of 30, pH of 3 were selected to achieve optimum oxidation. The optimum conditions in coagulation process: pH, cationic polyacrylamide dosage, mixing speed and time is 4.3, 2 mg/L, 150 rpm and 30 s, respectively. In the continuous treatment process under optimized conditions, the COD of oily wastewater fell 56.95%, 46.23%, 30.67%, respectively, from last stage and the total COD removal efficiency reached 83.94% (from 4,314 to 693 mg/L). In the overall treatment process under optimized conditions, the COD of oily wastewater was reduced from 4,314 to 637 mg/L, and the COD removal efficiency reached 85.23%. The contribution of each stage is 68.45% (micro-electrolysis), 24.07% (Fenton oxidation), 7.48% (coagulation), respectively. Micro-electrolysis is the uppermost influencing process on COD removal. Compared with the COD removal efficiency of three processes on raw wastewater under optimized conditions: the COD removal efficiency of single micro-electrolysis, single Fenton oxidation, single coagulation is 58.34%, 44.88% and 39.72%, respectively. Experiments proved the effect of combined process is marvelous and the overall water quality of the final effluent could meet the class III national wastewater discharge standard of petrochemical industry of China (GB8978-1996).

Sign in / Sign up

Export Citation Format

Share Document